The hoist consists of a single rope and an arrangement of frictionless pulleys as shown. If the angle 0 = 59°, determine the force that must be applied to the rope, Frope, to lift a load of 4.4 kN. The three-pulley and hook assembly at the center of the system has a mass of 22.5 kg with a center of mass that lies on the line of action of the force applied to the hook. e ΘΕ B CC 10 BY NC SA 2013 Michael Swanbom Fhook Note the figure may not be to scale. Frope = KN HO Frope

The hoist consists of a single rope and an arrangement of frictionless pulleys as shown. If the angle 0 = 59°, determine the force that must be applied to the rope, Frope, to lift a load of 4.4 kN. The three-pulley and hook assembly at the center of the system has a mass of 22.5 kg with a center of mass that lies on the line of action of the force applied to the hook. e ΘΕ B CC 10 BY NC SA 2013 Michael Swanbom Fhook Note the figure may not be to scale. Frope = KN HO Frope

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.42P: The 350-lb homogeneous plate has the shape of an isosceles triangle. The plate is supported by a...

See similar textbooks

Similar questions

The 350-lb homogeneous plate has the shape of an isosceles triangle. The plate is supported by a thrust hinge at A, a slider hinge at B, and the cable CD. Find the force in the cable and the magnitudes of the hinge reactions.
The homogeneous 20-kg door is held in the horizontal plane by a thrust hinge at O, a hinge at A, and the vertical prop BC. Determine all forces acting on the door.
The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A and B. Neglect friction.
The 180-lb homogeneous bar is supported by a ball-and-socket joint at A and two cables attached to B. Determine the forces in the cables.
The center of gravity of the 3000-lb car is at G. The car is parked on an incline with the parking brake engaged, which locks the rear wheels. Find (a) the normal forces (perpendicular to the incline) acting under the front and rear pairs of wheels; and (b) the friction force (parallel to the incline) under the rear pair of wheels.
The uniform, 20-kg bar is placed between two vertical surfaces. Assuming sufficient friction at A to support the bar, find the magnitudes of the reactions at A and B.
The 80-kg crate has its center of gravity at G. Determine the smallest force P that will initiate motion if =35.
Determine the smallest horizontal force P that would push the homogeneous cylinder of weight W over the curb. Neglect friction.
The L-shaped rod AOCD has an 80 kg mass hanging from it at B. The rod is leaning against a smooth wall at A. Point B is half way up OA. There is a journal bearing at C and a thrust bearing at D. They are properly aligned. A force F is pulling in the x-direction at B. Just as the rod comes off of the wall at A, what is the magnitude of the force F. 1 m B F 1m
The jib crane is designed for a maximum capacity of 14 kN, and its uniform I-beam has a mass of 270 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 4.9 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 2.4 m? (b) What is the value of R when x = 4.5 m? (c) Determine the minimum value of R and the corresponding value of x. (d) For what value of R should the pin at A be designed? 1.6 m Questions: 25° 14 KN -3.5 m (a) If x = 2.4 m, R = (b) If x= 4.5 m, R= (c) The minimum value for R = i (d) The pin should be designed to hold i KN KN kN at x = i kN. m
The jib crane is designed for a maximum capacity of 7 kN, and its uniform I-beam has a mass of 160 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.6 m. On the same set of axes, plot the x- and y-components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work.(a) What is the value of R when x = 0.9 m?(b) What is the value of R when x = 3.1 m?(c) Determine the minimum value of R and the corresponding value of x.(d) For what value of R should the pin at A be designed?
As part of a check on its design, a lower A-arm (part of an automobile suspension) is supported by bearings at A and Band subjected to the pair of 910-N forces at C and D. The suspension spring, not shown for clarity, exerts a force FSat E as shown, where E is in plane ABCD. Determine the magnitude FS of the spring force and the magnitudes FA and FB of the bearing forces at A and B which are perpendicular to the hinge axis AB. Fs=____N Fa=____N Fb=____ N