University of SamarraCollege of engineeringElectromech. Eng. DeptPower Electronics 1 monthly examQ1) A single phase AC voltage one-directional controller has a resistive load of 10 92 and the inputvoltage of 120 V, 60 Hz. The delay angle of the thyristors TI & T2 are л/3. Determine the r.m.svalue of output voltage, average current of thyristors, and effective values of thyristors current. Also,draw the circuit.

Answered: Image /qna-images/answer/cb338bd1-2b3a-49c0-9578-e9fb79823fef.jpg

Answered: University of Samarra College of…

Understanding Motor Controls

4th Edition

ISBN:9781337798686

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter53: The 555 Timer

Section: Chapter Questions

Problem 2RQ

See similar textbooks

Similar questions

estion 1 The step resolution of a stepper motor is set for 1024 steps per revolution, Find the frequency to rotate at 60 rpm. (Give your answer in Hertz, put only numeric value) Question 3 A proportional valve is handled by an PWM signal Question 4 The speed of a stepper motor is controlled by Question 5 The relay is driven by an analog signal Question 6 Determine the output voltage from a PWM pin when the time ON is 25 ms and the frequency is 1kHz and Vcc-SV. (Put only a number in Volt, no need to add the unit word)
2- for a DSB-SC modulator with calculations, assuming perfect carrier pression: usdal Modula ng Signal cerario: Carrier freque Modulating c) = 1 t), whe m = 1 kHz (20 marks)
i need a explanation about this picture and what it's work the system of DCV In detail and briefly please
Show the circuit diagram
) Explain the procedure adopted to arrive at the specification of piezo electric sensor charge amplifiercrank angle encoder and AD convener with data storage for heat release analysis of a given IC engine. (b) Discuss the method of obtaining pressure crank angle diagram. List down the parameters that can bestudied from the pressure crank angle diagram.
MECT361 Mechatronics Components and Instrumentation PLEASE GIVE ME THE short answer and wite it by keyword thanks
6. In a NC system, the motor is connected directly to the leadscrew, which has a pitch of 4 mm, 40 step angles, storage capacity of 8 bits, and a 10 mm axis range. Its control resolution equals: None of the choices 0.005 0.039 0.10
Answer all parts show work
%.VE I CLASS: 4th A 0: E 2_5361633277343... 1 Term Exam (2014-2015) Q1 The following block diagram represents the drying oven control system. The dynamic behavior of the oven can be represented by following differential equation: de (1) 10 +00(0) = v(1) di Calculate the following: a-Natural frequency, and damping ratio b-The response of the system to step change in 0,(t) of 20 C° E(s) 0. (s) V(s) 30 Oven 2 3+4. (50M) For the control system shown in figure find an expression for C(s) in terms of R₁(s) and R₂(s). R₁(s) 2 C(s) 5 Ra(s) (50M) Examiner FOUNDATION OF TECHNICAL EDUCATION COLLEGE OF TECHNOLOGY/KIRKUK Fuel & Energy ENG. DEP. CLASS 4 SUB.: Cont. & Measur DATE 3/6/2015 TIME:3 Hours / المجنح الامتحانية المركزية لسنة الدراسية. 2014-2015 Final Exam (2014-2011 A The following block diagram represents the PI control to a chemical process .The process is described by the following differential equation.:: dy(t) 2 + y(t) = 2v(t) dt Calculate the following: a-Natural frequency a, and…
2. Figure 1 shows a sensor consists of a core, an armature and a variable air gap. The core with 3.0 cm depth and 10000 relative permeability has 200 coil turns. On the other hand, the armature is a steel plate of thickness 0.2 cm and has similar relative permeability with the core. Assuming the relative permeability of air is unity and the permeability of free space is equal to 4x x 10-7 H.m, calculate the inductance of the sensor for air gaps of 0 mm and 2 mm. Please write the answers in 3 decimal places. 2.0 cm 1.0 cm 6.0 cm 3.0 cm 1.5 cm Figure I
can you please find the solution for this?
A liquid-level process control system is shown in Figure 5a and its closed loop representation is shown in Figure 5b. The system parameters are: A = 2 m², Rf = 15 s/m², H₁= 1 V/m, K₁ = 1 m³/sV, K₁ = 1. What are the values of Ti and when the undamped natural frequency WT = 0.01 rad/s? Answer should be supported with appropriate calculation steps. hul!) Pl hon Controller Control Valve K₁ Pressure transducer H₁ Figure 5a. Tank Area A Outlet valve Resistance R/\10 PI Controller Tank and valve Control valve H₁(s) Ha(s) E(s) U(s) V₁(8) K₁ K₁ R₁ 1+ARS Hm(s) Pressure tranducer H₁ Figure 5b. Ꮵ.

SEE MORE QUESTIONS

Recommended textbooks for you

Understanding Motor Controls

Mechanical Engineering

ISBN:

9781337798686

Author:

Stephen L. Herman

Publisher:

Delmar Cengage Learning

Automotive Technology: A Systems Approach (MindTa…

Mechanical Engineering

ISBN:

9781133612315

Author:

Jack Erjavec, Rob Thompson

Publisher:

Cengage Learning

Understanding Motor Controls

Mechanical Engineering

ISBN:

9781337798686

Author:

Stephen L. Herman

Publisher:

Delmar Cengage Learning

Automotive Technology: A Systems Approach (MindTa…

Mechanical Engineering

ISBN:

9781133612315

Author:

Jack Erjavec, Rob Thompson

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS