Answer question 1 please Question 1The joint is subjected to the force system shown. Determine the state of stress at points A and B.The member has a rectangular cross-sectional area of width 0.5 in. and thickness 1 in.AaBB1 in2 in.250 lb1.5 in.500 lbQuestion 2Do research on "blue brittleness" of steels. Used the information gleaned to:(a) Explain what blue brittleness is.(b) Explain how blue brittleness could affect the impact test results for the steel that wastested at elevated temperature.

Answered: Question 1 The joint is subjected to…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The femur, the long bone in the thigh, can be modeled as a tube of compact bone for most of its length. The cross-section area of the compact bone in the femur of a 70 kg person is 4.8 x 10-4 m2, a typical value.a. If this person supports his entire weight on one leg, what fraction of the tensile strength of the bone does this stress represent?b. By what fraction of its length does the femur shorten?
Using the tensile test simulation tool, a. generate the stress-strain curve for aluminum b. Indicate the following points in the stress-strain curve for aluminum and give the corresponding values: limit of proportionality elastic limit 0.2% offset yield stress (include the graph illustrating how this was determined) ultimate stress fracture stress c. Calculate modulus of elasticity. d. compare aluminum with nylon (include the related graph) and answer the following: Which has higher tensile strength? Provide the necessary values to support the answer. Which is stiffer? Support your answer with calculations.
need help Engineering of Materials
Please complete the following with full workings. :)
A tensile force. of 120 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load, the diameter decreases to 0.01998 m and the length increases to 2.01 m. The true stress on that rod is?
An engineer determines that a 32 cm long rod of 1020 grade steel will be subjected to a tension of 40 kN. The following two design requirements must be met: the stress must remain below 120 MPa, and the rod must stretch less than 0.135 mm. Determine an appropriate value for the rod's diameter to meet these two requirements. (Round up to the nearest millimeter when reporting your answer.) mm
The state of stress at a point in a member is shown on the element. Suppose that o = -50 MPa , oy = -120 MPa , Try = -30 MPa Part A Determine the normal stress component acting on the plane AB. (Figure 1) Express your answer with the appropriate units. HA Value Units Submit Request Answer Figure 1 of 1 Part B A Determine the shear stress component acting on the plane AB. Express your answer with the appropriate units. 30% HA ? Tz'y = Value Units Submit Request Answer B
Describe stress and its three types along with graphical representation and mathematical formula of each type.
Which material/metal is the stiffest based on the following data provided and why?
Determine the tensile yield strength (0.2% offset) and the maximum strength of a metal alloy having the following tensile stress-strain diagram. Select one: The tensile yield strength Sy = 100 Mpa and the maximum strength Smax = 250 Mpa. The tensile yield strength Sy = 170 Mpa and the maximum strength Smax = 250 Mpa. The tensile yield strength Sy = 150 Mpa and the maximum strength Smax = 200 Mpa. The tensile yield strength Sy = 240 Mpa and the maximum strength Smax = 250 Mpa. The tensile yield strength Sy = 80 Mpa and the maximum strength Smax = 250 Mpa.
Determine the tensile yield strength (0.2% offset) and the maximum strength of a metal alloy having the following tensile stress-strain diagram. Select one: The tensile yield strength Sy = 100 Mpa and the maximum strength Smax = 250 Mpa. The tensile yield strength Sy = 170 Mpa and the maximum strength Smax = 250 Mpa. The tensile yield strength Sy = 150 Mpa and the maximum strength Smax = 200 Mpa. The tensile yield strength Sy = 240 Mpa and the maximum strength Smax = 250 Mpa. The tensile yield strength Sy = 80 Mpa and the maximum strength Smax = 250 Mpa.
I want answer please from these choses and I need them to be correct please

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS