1. Water is flowing inside of a 3-std type K copper tube at a flow rate of 1.2 kg/s. The average temperature of the water is 50°C. Cold, dry air at a temperature of 5°C and atmospheric pressure flows outside of the tube in cross flow with a velocity of 85 m/s. Determine the UA product for this tube under clean conditions.

1. Water is flowing inside of a 3-std type K copper tube at a flow rate of 1.2 kg/s. The average temperature of the water is 50°C. Cold, dry air at a temperature of 5°C and atmospheric pressure flows outside of the tube in cross flow with a velocity of 85 m/s. Determine the UA product for this tube under clean conditions.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.1P: 6.1 Determine the heat transfer coefficient at the stagnation point and the average value of the...

See similar textbooks

Similar questions

Milk is Pasteurized by first heating it to 71oC, and keeping it at that temperature for 17 seconds before cooing it rapidly for bottling. Fresh milk at 5oC enters the Pasteurization unit where it flows through a thin-walled stainless steel (SS) tube of 2.0 cm diameter. The inside surface of the tube is such that the flow is turbulent to promote good mixing and uniform temperature across the flow at every point along the tube. Heating is provided by passing the tube in a closed container that is filled with saturated steam at atmospheric pressure and 100oC. Hence, we can assume that the thin-walled SS tube temperature is maintained at 100oC all along its length by condensing steam over the outside surface. The flow-rate of milk is 40kg per minute (i.e. approximately 10 gallons per minute). a) What is the mean velocity (m/s) and ??? for the milk flowing through the tube between 1-2? b) What is the convective heat transfer coefficient h (W/m2K) over the inside surface of the tube? c) What…
Not Ai generated answers, I need to understand please show all steps.
Plz urgent plzzzzz....i need solution plz.fast plz plz plz..hand written plz asap... I'll rate
In a concentric-pipe heat exchanger, one of the fluids is a condensing vapour and theother is the coolant. Sketch the variation in fluid temperatures of two fluids as theyflow through the heat exchanger. Indicate clearly the inlet and outlet of the coolantand its direction of flow.
Consider pressurized water, engine oil (unused), and Nak (22%/78%) flowing in a 20-mm-diameter tube. (a) Determine the mean velocity, in m/s, the hydrodynamic entry length, in m, and the thermal entry length, in m, for each of the fluids when the fluid temperature is 366 K and the flow rate is 0.01 kg/s. (b) Determine the mass flow rate, in kg/s, the hydrodynamic entry length, in m, and the thermal entry length, in m, for water and engine oil at 300 and 400 K and a mean velocity of 0.022 m/s. Part A Determine the mean velocity, in m/s, the hydrodynamic entry length, in m, and the thermal entry length, in m, for each of the fluids when the fluid temperature is 366K and the flow rate is 0.01 kg/s. Liquid Um (m/s) Xfdh (m) Xfd,t (m) water i engine oil i i i Nak i
Please show all steps, not Ai generated, has been wrong before. I need to understand the process.
Write the assumptions in flow through circular tube?
Pls solve the question in the image
Flow Characteristics (Entrance Effect) -Why is the Δ P/ L Line extrapolated to the tube entrance for the calculation of the entrance loss coefficient, KL ?
Flow Characteristics( Entrance Effect) Why was there some disagrement between the actual Pitot tube velocity profile and the power law velocity profile?
Please don't provide handwritten solution .....
Corsidera circular smoth pipeof inner diameter D;=0.015mwhose inner surface is covered with a layer of liquid as a result of condensation. In order to dry the inner surface of the pipe, air at 300K at 1 atmis forced to flow throughit with anaverage velocity of 1.2m/s. Using the analogy between heat and mass trarsfer, detemine the mass transfer coeffícient irside the pipe for fully developed flow. Note: Viscosity of the air for given conditions is given as 1.58 x 10°n?/s. Also, for a lamirar fully developed flow the N=Sh=3.66. Your solution must state governing equations and associated assumptions, illustration and step by step execution of the overall solution