A gear train has a 50.3 mm circular pitch and a 25 degree pressure angle and meshes with a pinion having 12 teeth Design this gear train to minimize its volume and the total number of teeth. Obtain the pitch diameters the number of teeth the speed ratio the center distance and the module of this gear train. The gearbox housing has a diameter of 620mm

A gear train has a 50.3 mm circular pitch and a 25 degree pressure angle and meshes with a pinion having 12 teeth Design this gear train to minimize its volume and the total number of teeth. Obtain the pitch diameters the number of teeth the speed ratio the center distance and the module of this gear train. The gearbox housing has a diameter of 620mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A gear train with a ratio of -6:1 and a diametral pitch of 8 is used to reduce the speed from an electric motor to a shaft driving a grocery checkout conveyor. Grocery checkout conveyor Electric motor @, = 1800 rpm a. If the motor rotates at 1800 rpm clockwise, determine the speed and direction of the large gear. b. For a pressure angle of 20 deg, determine the minimum number of teeth for the pinion. Assume the gears are cut by a shaper (NOT a hob). c. Specify pitch diameters and numbers of teeth for the pinion and the gear for the most compact gear train.
A pinion having 40 teeth drives a gear having 80 teeth. the profile of the gear is involute with pressure angle ( 22), 12 mm module and (14) mm addendum. Find 1-the length of contact2-Arc of contact 3-Contact ratio
The teeth of the gear arrangement have Gear A=40teeth, Gear B=70 teeth and Gear C= 50teeth, a pinion (driver Gear) that rotates at 625 rpm, and idler Gear B and a driven gear (Gear C). The gears have a module of 5mm and a pressure angle of 200. Find the pitch diameter of gear C in mm.
please help
Helical Gears, Bevel Gears, and Wormgearing 3
please help
A pair of helical gears are machined with a hob. The hob has a 20 degree pressure angle and machines circular pitch of 0.55 inch/tooth on a spur gear. Two gears are machined, the pinion has 18 teeth and the gear has 36 teeth. The measured transverse diametral pitch on the pinion is 5 inch/tooth. The pinion transmits 10 hp at 1,000 rpm. Calculate the center distance of the gearset, in inches
A similar pair of helical gears , also on parallel axes, are to have involute teeth, of 20o normal pressure angle, and 3 mm normal module. The wheels are to have 26 and 34 teeth, and to work with a centre distance of 146 mm. Calculate the transverse pressure angle in degrees.
The maximum sliding velocity of the teeth of two gear wheels in mesh is 0.32 m/s. The wheels are of module 5 mm and have 32 and 44 teeth respectively. The addendum for each wheel is 1.2 times the module and the pressure angle is 20°. Calculate: 2.1. The number of teeth in contact. 2.2. The angular speed of each wheel.
i need the answer quickly
pls expalin to me step by step and write clearly. i will rate your answer immediately thanks
In a gear set, a 36-tooth spur pinion drives a 60-tooth spur gear. The teeth of these gear are cast iron profile. The diametral pitch is 6-teeth/in, the face width si 0.5 inches, and the pressure angle is 20 degrees. Assume that the pinion transmits 10 hp at a speed of 2000 rpm. Find the pitch diameters of the gears. Find the pitch line velocity in ft/min Find the velocity factor Ky Find the tangential load in lbf Find the contact stress in kpsi, assuming CP=1960 psi.