an experimental research station is constructed on a concrete slab floor. The heat loss from the floor slab is significant, given the cold environment, and is measured to be 5 kW. The edges of the floor slab are insulated with a 60 mm thickness of cellular glass insulation. The width of this insulation at the floor slab is 0.9 m. To avoid excessive fuel consumption, the station air temperature is maintained at a slightly cool temperature of 18ºC. The station is constructed in a square shape, to keep the surface area to volume ratio low; the horizontal dimensions of the floor of the station are 20 m by 20 m. The number of occupants in the research station varies between 5 and 20, depending on the research workload.a) Determine the design outdoor temperature that was used in designing the research station.b) If the floor dimensions of the station are changed to 15 m by 25 m, would the design outdoor temperature that was used in designing the research station from part (a) change? If so, what would it be?

an experimental research station is constructed on a concrete slab floor. The heat loss from the floor slab is significant, given the cold environment, and is measured to be 5 kW. The edges of the floor slab are insulated with a 60 mm thickness of cellular glass insulation. The width of this insulation at the floor slab is 0.9 m. To avoid excessive fuel consumption, the station air temperature is maintained at a slightly cool temperature of 18ºC. The station is constructed in a square shape, to keep the surface area to volume ratio low; the horizontal dimensions of the floor of the station are 20 m by 20 m. The number of occupants in the research station varies between 5 and 20, depending on the research workload.a) Determine the design outdoor temperature that was used in designing the research station.b) If the floor dimensions of the station are changed to 15 m by 25 m, would the design outdoor temperature that was used in designing the research station from part (a) change? If so, what would it be?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.33P

See similar textbooks

Similar questions

The air-conditioning system in a Chevrolet van for use in desert climates is to be sized. The system is to maintain an interior temperature of 20C when the van travels at 100 km/h through dry air at 30C at night. If the top of the van is idealized as a flat plate 6 m long and 2 m wide and the sides as flat plates 3 m tall and 6 m long, estimate the rate at which heat must be removed from the interior to maintain the specified
Required information Consider an electrically heated brick house (k = 0.40 Btu/h-ft-°F) whose walls are 9 ft high and 1 ft thick. Two of the walls of the house are 50 ft long and the others are 35 ft long. The house is maintained at 70°F at all times while the temperature of the outdoors varles. On a certain day, the temperature of the Inner surface of the walls is measured to be at 64°F while the average temperature of the outer surface is observed to remain at 45°F during the day for 10 h and at 35°F at night for 14 h. 35 ft 50 ft 9 ft Determine the amount of heat lost from the house that day. (You must provide an answer before moving on to the next part.) The amount of heat lost from the house that day is [ 18526 Btu.
a station is constructed on a concrete slab floor. The heat loss from the floor slab is significant, given the cold environment, and is measured to be 5 kW. The edges of the floor slab are insulated with a 60 mm thickness of cellular glass insulation. The width of this insulation at the floor slab is 0.9 m. To avoid excessive fuel consumption, the station air temperature is maintained at a slightly cool temperature of 18ºC. The station is constructed in a square shape, to keep the surface area to volume ratio low; the horizontal dimensions of the floor of the station are 20 m by 20 m. The number of occupants in the research station varies between 5 and 20, depending on the research workload.a) Determine the design outdoor temperature that was used in designing the research station.b) If the floor dimensions of the station are changed to 15 m by 25 m, would the design outdoor temperature that was used in designing the research station from part (a) change? If so, what would it be?…
⚫ A thin silicon chip and an 8-mm-thick aluminum substrate are separated by a 0.02-mm-thick epoxy joint. The chip and substrate are each 10 mm on a side, and their exposed surfaces are cooled by air, which is at a temperature of 25C and provides a convection coefficient of 100 W/m2 K. If the chip dissipates 104 W/m2 under normal conditions, will it operate below a maximum allowable temperature of 85C? 7-25°C Air -100 W/m²K Insulation Silicon chip Ероку joint (0.02 mm) Aluminum substrate 7-25 C Air -100 W/mK L-8 mm
A wall in a house contains a single window. The window consists of a single pane of glass whose area is 0.13 m2 and whose thickness is 8 mm. Treat the wall as a slab of the insulating material Styrofoam whose area and thickness are 19 m2 and 0.10 m, respectively. Heat is lost via conduction through the wall and the window. The temperature difference between the inside and outside is the same for the wall and the window. Of the total heat lost by the wall and the window, what is the percentage lost by the window?
Under conditions for which the same room temperature is maintained by a heating or cooling system, it is not uncommon for a person to feel chilled in the winter but comfortable in the summer. Consider a room whose air temperature is maintained at 22°C throughout the year, while the walls of the room are nominally at 24°C and 12°C in the summer and winter, respectively. The exposed surface of a person in the room may be assumed to be at a temperature of 32°C throughout the year and to have an emissivity of 0.90. The coefficient associated with heat transfer by natural convection between the person and the room air is approximately 2 W/m2-K. Calculate the following. Heat flux due to convection: qbonv W/m? Heat flux due to radiation in the summer: Trad i W/m? Heat flux due to radiation in the winter: gad W/m? i Physical Properties Mathematical Functions
Pravinbhai
A thin silicon chip and an 8-mm-thick aluminum substrate are separated by a 0.02-mm-thick epoxy joint. The chip and substrate are each 10 mm on a side, and their exposed surfaces are cooled by air, which is at a temperature of 25°C and provides a convection coefficient of 100 W/m²K. If the chip dissipates 104 W/m² under normal conditions, will it operate below a maximum allowable temperature of 85°C? Known: Dimensions, Heat dissipation, and maximum allowable temperature of a silicon chip. Thickness of aluminum substrate and epoxy joint. Convection conditions at exposed chip and substrate surfaces. Find: Whether maximum allowable temperature is exceeded. Assumption: Steady-state conditions, One-dimensional conduction (negligible heat transfer from sides of composite). Negligible chip thermal resistance (an isothermal chip), Constant properties. Negligible radiation exchange with surroundings. Properties: Table A.1, pure aluminum (T~350 K): k = 239 W/m K. Air Too = 25°C h = 100 W/m²K -…
The rectangular wall of a furnace consists of 3in. fire clay brick surrounded by 0.25in. of steel on the outside. There are six 0.25in.diameter mild steel bolts per square foot connecting the steel and the brick. The furnace is surrounded by 70°F air (with a film coefficient of 1.65 Btu/hr-ft²-°F), while the inner surface of the brick is maintained at a constant 1000°F. Determine the heat flux per square foot through this wall?
A concrete wall, which has a surface area of 20 m2 and is 0.30 m thick, separates conditioned room air from ambient air. The temperature of the inner surface of the wall is maintained at 25°C, and the thermal conductivity of the concrete is 1 W/mK.(a) Determine the rate of heat loss through the wall for outer surface temperatures ranging from −15°C to 38°C, which correspond to winter and summer extremes, respectively. Display your results graphically.(b) On your graph, also plot the rate of heat loss as a function of the outer surface temperature for wall materials having thermal conductivities of 0.75 and 1.25 W/m⋅K. Explain the family of curves you have obtained
A large steel plate having a thickness of L = 4 in, thermal conductivity of k= 7.2 Btu/h·ft. °F, and an emissivity of ε = 0.7 is lying on the ground. The exposed surface of the plate at x = L is known to exchange heat by convection with the ambient air at T∞ = 90°F with an average heat transfer coefficient of h = 12 Btu/h·ft².°F as well as by radiation with the open sky with an equivalent sky temperature of Tsky =480 R. Also, the temperature of the upper surface of the plate is measured to be 80°F. Assuming steady one-dimensional heat transfer, (a) express the differential equation and the boundary conditions for heat conduction through the plate, (b) obtain a relation for the variation of temperature in the plate by solving the differential equation, and (c) determine the value of the lower surface temperature of the plate at x = 0. Tsky h, To Convection Radiation XA 80°F L E Plate 0 Ground
A cylindrical storage tank with diameter of 4m and a length of 10 m will hold a fluid whose temperature must be maintained at 347k. in order to size the heater required for the tank the following worst-case scenario is considered: Ambient temperature=-20 wind speed=20m/s tank wall temperature=347k what size (kW) heater will be needed?