Homework Help is Here – Start Your Trial Now!
Engineering
Mechanical Engineering
A Use the general dimensioning symbols to correctly specify the following requirements on the drawing above. A. The nominal height of the part is 40mm. The tolerance on the height of the part is 1 mm equally distributed. Provide instructions to the inspector that the height of the part must be verified by using a height gage when the bottom of the part is resting on a surface plate. B. 6 to 6.4mm square hole must go through both sides of the part with an equally distributed size tolerance of 0.4mm. c. The nominal size of the two holes labeled "A" is 8.5mm. The top side of the hole must have a tapered lead in of 14 mm diameter with an included angle of 90°. The title block tolerance applies to the counter sink diameter. d. The two holes labeled "B" have a nominal size of 8.5mm with an unequally distributed size tolerance of plus 0.2 and minus 0.1mm. The top surface around each hole must be cleaned to a 15 minimum diameter area. e. The hole in the center of the part is a 16.2 diameter. The hole can get 0.2mm bigger, but not smaller. A second 30 mm flat bottomed coaxial hole must be machined to a min depth of 17.7mm and a max depth of 18.3mm. f. The four corners of the part must have a radius with a minimum of 9mm and a maximum of 9.6mm.

A Use the general dimensioning symbols to correctly specify the following requirements on the drawing above. A. The nominal height of the part is 40mm. The tolerance on the height of the part is 1 mm equally distributed. Provide instructions to the inspector that the height of the part must be verified by using a height gage when the bottom of the part is resting on a surface plate. B. 6 to 6.4mm square hole must go through both sides of the part with an equally distributed size tolerance of 0.4mm. c. The nominal size of the two holes labeled "A" is 8.5mm. The top side of the hole must have a tapered lead in of 14 mm diameter with an included angle of 90°. The title block tolerance applies to the counter sink diameter. d. The two holes labeled "B" have a nominal size of 8.5mm with an unequally distributed size tolerance of plus 0.2 and minus 0.1mm. The top surface around each hole must be cleaned to a 15 minimum diameter area. e. The hole in the center of the part is a 16.2 diameter. The hole can get 0.2mm bigger, but not smaller. A second 30 mm flat bottomed coaxial hole must be machined to a min depth of 17.7mm and a max depth of 18.3mm. f. The four corners of the part must have a radius with a minimum of 9mm and a maximum of 9.6mm.

Welding: Principles and Applications (MindTap Course List)
Welding: Principles and Applications (MindTap Course List)
8th Edition
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Larry Jeffus
Chapter20: Shop Math And Weld Cost
Section: Chapter Questions
Problem 24R: What is a dimensioning tolerance?
See similar textbooks
icon
Related questions
Question

Need help in adding demensioning am am so confused

A Use the general dimensioning symbols to correctly specify the following requirements on the drawing above. A. The nominal height of the part is 40mm. The tolerance on the height of the part is 1 mm equally distributed. Provide instructions to the inspector that the height of the part must be verified by using a height gage when the bottom of the part is resting on a surface plate. B. 6 to 6.4mm square hole must go through both sides of the part with an equally distributed size tolerance of 0.4mm. c. The nominal size of the two holes labeled "A" is 8.5mm. The top side of the hole must have a tapered lead in of 14 mm diameter with an included angle of 90°. The title block tolerance applies to the counter sink diameter. d. The two holes labeled "B" have a nominal size of 8.5mm with an unequally distributed size tolerance of plus 0.2 and minus 0.1mm. The top surface around each hole must be cleaned to a 15 minimum diameter area. e. The hole in the center of the part is a 16.2 diameter. The hole can get 0.2mm bigger, but not smaller. A second 30 mm flat bottomed coaxial hole must be machined to a min depth of 17.7mm and a max depth of 18.3mm. f. The four corners of the part must have a radius with a minimum of 9mm and a maximum of 9.6mm.
Transcribed Image Text:A Use the general dimensioning symbols to correctly specify the following requirements on the drawing above. A. The nominal height of the part is 40mm. The tolerance on the height of the part is 1 mm equally distributed. Provide instructions to the inspector that the height of the part must be verified by using a height gage when the bottom of the part is resting on a surface plate. B. 6 to 6.4mm square hole must go through both sides of the part with an equally distributed size tolerance of 0.4mm. c. The nominal size of the two holes labeled "A" is 8.5mm. The top side of the hole must have a tapered lead in of 14 mm diameter with an included angle of 90°. The title block tolerance applies to the counter sink diameter. d. The two holes labeled "B" have a nominal size of 8.5mm with an unequally distributed size tolerance of plus 0.2 and minus 0.1mm. The top surface around each hole must be cleaned to a 15 minimum diameter area. e. The hole in the center of the part is a 16.2 diameter. The hole can get 0.2mm bigger, but not smaller. A second 30 mm flat bottomed coaxial hole must be machined to a min depth of 17.7mm and a max depth of 18.3mm. f. The four corners of the part must have a radius with a minimum of 9mm and a maximum of 9.6mm.
Expert Solution
steps

Step by step

Solved in 2 steps with 2 images

SEE SOLUTIONCheck out a sample Q&A here
Blurred answer
Similar questions
  • SEE MORE QUESTIONS
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou…
Welding: Principles and Applications (MindTap Cou…
Mechanical Engineering
ISBN:
9781305494695
Author:
Larry Jeffus
Publisher:
Cengage Learning
SEE MORE TEXTBOOKS