A bar of length L and of a circular cross-section of diameter D is clamped at the top end and loaded at the other (bottom) end by a point load P as shown in FigureQ2a. The cross-section of the bar is shown in Figure Q2b indicating that load is applied at the point A. The material used in the bar has specific weight y.Find the magnitude and location of the maximum normal stress in the bar.Figure Q2 aFigure Q2 b45°A If L-719.01 mm, = 7839.63 N/m³, the normal stress σ caused by self-weight at the location of the maximum normal stress in the bar can be calculated as(Please select the correct value of σ given in Pa and rounded to three decimal places.)Select one:○ 1. 1409.1932. 845.516O 3. 11273.545○ 4.8455.159○ 5.4509.4186. 2818.3867.5636.772

Answered: Image /qna-images/answer/3083f39d-ad26-4f71-83f7-6c9e12da5f44.jpg

Answered: A bar of length L and of a circular…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a standard tensile test, an aluminum rod of 20-mm diameter is subjected to a tension force of P= 30 kN. It is given that v = 0.35 and E= 70 GPa. 20-mm diameter 150 mm P' Determine the change in diameter of the rod. (Round the final answer to six decimal places.) The change in diameter of the rod is - 0.009207 mm.
8 x = 17 MPa y = 41 MPa T = 56 MPa 5 T σχ X At a point on a structural member subjected to plane stress, normal and shear stresses exist on horizontal and vertical planes through a point as shown. Use the stress transformation equations to determine the normal stress to the nearest 0.01 MPa on the indicated plane. Be sure to use - as appropriate. 277
Need only a handwritten solution only (not a typed one).
The stress state of the body of a power screw is defined by a stress cube, as: -10.39 MPa 6.07 MPa -4.04 MPa 6. If σx = 35 MPa, determine the maximum principal stress (in MPa). Use Excel spreadsheet posted on Canvas and give correct answer to one decimal place.
An 6 mm diameter aluminum rod has lines scribed on it that are exactly 10 cm apart. After a 2.08 kN force has been applied, the separation between the lines has increased to l' = 10.009 cm. 30 cm 10 cm -F l' a. Calculate the stress and strain in the rod. (Express your answer for stress using two significant figures.) |MPa (Express your answer for strain using four decimal spaces.) E = b. To what total length has the rod stretched? (Express your answer using three decimal places.) L final cm
Part A The state of stress at a point in a member is shown on the element. Suppose that oe = -50 MPa, oy = -100 MPa. , Tzy = -29 MPa. Determine the normal stress component acting on the plane AB. (Figure 1) Express your answer with the appropriate units. HÁ ? Figure 3 1 of 1 87.614 MPa Oe = A Submit Previous Answers Request Answer X Incorrect; Try Again; 5 attempts remaining 30 Part B Determine the shear stress component acting on the plane AB. В Express your answer with the appropriate units.
Two cylindrical rods, one of steel and the other of brass, are joined at C and Q1) restrained by rigid support at 4. There is a gap of 1 mm between end E and rigid support at right side. For the loading shown and knowing that E; = 200 GPa, E = 105 GPa, as = 13×106 1/°C and as = 19×10-6 1/°C, determine the minimum change in temperature to close the gap. Dimensions in mm 100 100 F180- 120- A D Brass Steel Be 60 kN 40 kN 20-mm diam. 10-mm diam.
Consider the loading shown. The allowable normal stress for the steel used is 172 MPa. For the selected design, determine the maximum value of the principal stress σmax at the junction of a flange and the web. (Round the final answer to one decimal place.)
The answer is one of the options below please solve carefully and circle the correct option Please write clear .
The state of stress at a point in a member is shown on the element. Determine the shear stress component T'xy (in ksi) acting on the inclined plane AB. Use Excel spreadsheet posted on Canvas and give correct answer to one decimal place. σx = 4.6 ksi đy = 3 ksi Txy = 10.7 ksi 0 = 40° A xy B 40° x
Determine the state of stress at point q. The pipe has an inner diameter of D₁ = 1.0 in and an outer diameter of = 1.8 in. Use the exact expression for Q, if needed. Label the reultant forces on the cross section below. Report your answer (3x3 matrix) in psi to one decimal place. Do 4 in. Y 4 in. 150 lb 6 in. 50 lb 10 in. 200 lb 150 lb X N Y
The state of in-plane stress at a point on an element of material is shown. Let |σx| = 370 MPa, |σy| = 130 MPa, and |τxy| = 85.0 MPa. Use this information to represent the state of stress of the same point that is rotated through an angle of θ = 25.0.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS