SPLIT CORES 贊助三 EXAMPLE 17 (UNDERIBED TYPE MOULD II) shaft plate (C14)-26 mm (1.0 in) thick (note that the mould backing plate may be used for this purpose). 16.21 EXAMPLE 17 (UNDERFEED TYPE MOULD 1) 16.21.1 Problem A Design a two-impression injection mould to produce the linked-shaped cover shown in Figure 16.108. A small centre gate into the base of the component is required. The cover is to be manufactured in HDPE. The drawing should include a plan view of the moving mould half, a plan view of the fixed mould half, and a side-sectional view of both mould halves. Drawing references: Plan view of the moving half (Figure 16.109); side- sectional view of both mould halves (Figure 16.110); plan view of the fixed mould half (Figure 16.111); isometric view of the moving half for reference purposes (Figure 16.112); isometric view of the fixed mould half for reference purposes (Figure 16.113); coolant flow-way circuit for the moving mould half (Figure 16.114); coolant flow-way circuit for the fixed mould half (Fines In 115) mould opening sequence (Figure 12.2). (Figure 16.110 is repeated and it is printed on the page facing Figure 16.111 for the reader's convenience.) PL 50 (2) -X XA EX Rad. S 18 To.71 1.5 SECTION (0.06) X-X Figure 16.108-Example 17: Link-shaped cover for which a two impression injection mould is required 689
SPLIT CORES 贊助三 EXAMPLE 17 (UNDERIBED TYPE MOULD II) shaft plate (C14)-26 mm (1.0 in) thick (note that the mould backing plate may be used for this purpose). 16.21 EXAMPLE 17 (UNDERFEED TYPE MOULD 1) 16.21.1 Problem A Design a two-impression injection mould to produce the linked-shaped cover shown in Figure 16.108. A small centre gate into the base of the component is required. The cover is to be manufactured in HDPE. The drawing should include a plan view of the moving mould half, a plan view of the fixed mould half, and a side-sectional view of both mould halves. Drawing references: Plan view of the moving half (Figure 16.109); side- sectional view of both mould halves (Figure 16.110); plan view of the fixed mould half (Figure 16.111); isometric view of the moving half for reference purposes (Figure 16.112); isometric view of the fixed mould half for reference purposes (Figure 16.113); coolant flow-way circuit for the moving mould half (Figure 16.114); coolant flow-way circuit for the fixed mould half (Fines In 115) mould opening sequence (Figure 12.2). (Figure 16.110 is repeated and it is printed on the page facing Figure 16.111 for the reader's convenience.) PL 50 (2) -X XA EX Rad. S 18 To.71 1.5 SECTION (0.06) X-X Figure 16.108-Example 17: Link-shaped cover for which a two impression injection mould is required 689
Elements Of Electromagnetics
7th Edition
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Sadiku, Matthew N. O.
ChapterMA: Math Assessment
Section: Chapter Questions
Problem 1.1MA
Related questions
Question

Transcribed Image Text:SPLIT CORES
贊助三
EXAMPLE 17 (UNDERIBED TYPE MOULD II)
shaft plate (C14)-26 mm (1.0 in) thick (note that the mould backing plate
may be used for this purpose).
16.21 EXAMPLE 17 (UNDERFEED TYPE MOULD 1)
16.21.1 Problem A
Design a two-impression injection mould to produce the linked-shaped
cover shown in Figure 16.108. A small centre gate into the base of the
component is required. The cover is to be manufactured in HDPE. The
drawing should include a plan view of the moving mould half, a plan view
of the fixed mould half, and a side-sectional view of both mould halves.
Drawing references: Plan view of the moving half (Figure 16.109); side-
sectional view of both mould halves (Figure 16.110); plan view of the
fixed mould half (Figure 16.111); isometric view of the moving half for
reference purposes (Figure 16.112); isometric view of the fixed mould half
for reference purposes (Figure 16.113); coolant flow-way circuit for the
moving mould half (Figure 16.114); coolant flow-way circuit for the fixed
mould half (Fines In 115) mould opening sequence (Figure 12.2).
(Figure 16.110 is repeated and it is printed on the page facing Figure
16.111 for the reader's convenience.)
PL
50
(2)
-X
XA
EX
Rad.
S
18
To.71
1.5
SECTION (0.06)
X-X
Figure 16.108-Example 17: Link-shaped cover for which a two impression injection
mould is required
689
Expert Solution

This question has been solved!
Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.
Step by step
Solved in 2 steps

Recommended textbooks for you

Elements Of Electromagnetics
Mechanical Engineering
ISBN:
9780190698614
Author:
Sadiku, Matthew N. O.
Publisher:
Oxford University Press

Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:
9780134319650
Author:
Russell C. Hibbeler
Publisher:
PEARSON

Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:
9781259822674
Author:
Yunus A. Cengel Dr., Michael A. Boles
Publisher:
McGraw-Hill Education

Elements Of Electromagnetics
Mechanical Engineering
ISBN:
9780190698614
Author:
Sadiku, Matthew N. O.
Publisher:
Oxford University Press

Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:
9780134319650
Author:
Russell C. Hibbeler
Publisher:
PEARSON

Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:
9781259822674
Author:
Yunus A. Cengel Dr., Michael A. Boles
Publisher:
McGraw-Hill Education

Control Systems Engineering
Mechanical Engineering
ISBN:
9781118170519
Author:
Norman S. Nise
Publisher:
WILEY

Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:
9781337093347
Author:
Barry J. Goodno, James M. Gere
Publisher:
Cengage Learning

Engineering Mechanics: Statics
Mechanical Engineering
ISBN:
9781118807330
Author:
James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:
WILEY