2.( , The blank for the spool shown in the figure below is to be sand cast out of A-319, an aluminum casting alloy. Make a sketch of the wooden pattern for this part. Include all necessary allowances for shrinkage and machining Shrinkage allowance = 10-20 mm/m, Machining allowance = 2 mm. Draft=30) 10 mm 100 mm 25 mm diameter 15 mm 75 mm

2.( , The blank for the spool shown in the figure below is to be sand cast out of A-319, an aluminum casting alloy. Make a sketch of the wooden pattern for this part. Include all necessary allowances for shrinkage and machining Shrinkage allowance = 10-20 mm/m, Machining allowance = 2 mm. Draft=30) 10 mm 100 mm 25 mm diameter 15 mm 75 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 4 a) Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for each piston is 175.00 mm. Calculate the cubic capacity of the engine in cm? and calculate the clearance volume per cylinder for a compression ratio, r, of 6.25. b) The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32 mm and the stroke of each piston is 125 mm. During testing., the engine runs at 1450 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 2.90 cm and a diagram length of 0.85 cm. The pressure scale on the indicator diagram is set to 165 kN/m per cm. Calculate the mean effective pressure (m.e.p) and the indicated power in kilowatts (kW) developed by this six-cylinder four-stroke engine. Give your answer to 2 decimal c) A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile load of 500 MN. If the maximum allowable stress for this hollow rod…
A circular shape blank will be cut of 107 mm diameter from a strip of 3.5 mm with a clearance value of 0.25 mm. Take the shear strength as 400 MPa. Determine The appropriate punch diameter. Blanking force. Blanking force when the blade angle is 5.70 o.
2) A washer is going to be manufactured by cutting operation out of 2024ST aluminum alloy sheet that has a thickness of 2.5 mm. The outside diameter of the washer is 25.0 mm, and the inside diameter is 12.0 mm. Make a rough sketch, define the geometries to be used and determine a. The punch and die size for the blanking operation b. The punch and die size for the punching operation c. The force required performing the blanking and punching operation simultaneously. The aluminum has a tensile strength = 300 MPa.
3- A planned extrusion operation involves cold-rolled steel at 1000° C to diameter of 75 mnm with length 65 mm and a final length 70 mm Two presses, one with capacity (extrusion force) of 30 MiN and the other with a capacity (extrusion force) of 20 MN, are available for the operation. Is the smaller press sufficient for this operation? K"=35x10*3 N [Hint: Calculate the extrusion force and compare it to the available two presses!
A hot/cold rolling setup is shown right. The operation first hot rolls a 3/8” thick plate, 12” wide (w), of6061 Aluminum, to an intermediate thickness, then finally through cold rolling, down to 1/4” thick plate.The friction factor μ is assumed to be constant at 0.15 for the hot roll, 0.12 for the cold rolling stage. Thefirst set of rolls operate at 50 RPM. Also ignore any width increase during rolling. CW=13% or .13 What is the plate thickness (mm) prior to the last rolls, t1, if the last set of rollers perform cold work reduction listed below at .13 or 13% Note that 9.52 mm is equal to 3/8 of an inch.
26c)A material has an mean indentation diameter of 3.64 mm created by a 5 mm diameter Brinell Indenter. Its hardness value is 200 HB , what will be applied force in Newtons?
A compound die will be used to blank and punch a large rectangle (90x150mm blank dimensions) out of 6061ST aluminum alloy sheet stock 3.5 mm thick. The diameter of inside hole is 25 mm. The aluminum sheet metal has a tensile strength 310 MPa. Determine the minimum tonnage press (force) to perform the blanking and punching operation (1) assume that blanking and punching occur simultaneously and (2) assume that punching occurs first, then blanking, Take: Ac-0.06
What force is required to punch a ½ inch hole on a 3/8 thick plate if the ultimateshearing strength of the plate is 42,000 psi?
QUESTION 14 Pieces thicker than 5.45mm are considered sheet. O True O False QUESTION 15 In sand casting, natural sands are less economical than synthetic sands. O True O False QUESTION 16 Typical sheet-metal thicknesses are between 0.15 mm and 7 mm. O True False
2. Calculate the blank size for the following sheet metal bending operation when the thickness of the sheet is 4mm, R-1.5t, A-60mm, B-250mm and C-80mm.
A stainless steel part is blanked from a larger sheet (0.5m wide, 1.0m long, 0.004m thick). Determine the tonnage (force) requirement for the blanking operation if the material shear strength is 600 MPa.
Assume you are bending a 3/16” thick rolled plate of Al 6061-T6 at a 90-degree angle. The initial bend radius (after the part is bent in the press brake) is 0.35”. Look up material properties on the Internet a) What is the final bend radius after the part has “relaxed”?b) Is it within the 2-4% rule of thumb?Show your work, and write down any values you choose to reference/use.