2. An adiabatic steam turbine has inlet conditions of 7 MPa, 500°C, 45 m/s and exit conditions of100 kPa, 75 m/s. The turbine has a power output of 5 MW and isentropic efficiency of 77%.(For this problem only, use Tables on next page). Find thea) steam mass flow rate through the turbine, (kg/sec)b) turbine exit temperature, (°C)c) rate of entropy generation for the process, (kW/K)

Answered: 2. An adiabatic steam turbine has inlet…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Finding exit temperature in F, and volumetric flow rate. Step by step solution please thank youuu
Pls. answer thank you! A steam turbine of 6 MW capacity has a Willan's line equation of ms = 5.52 + 3.200 kg/hr. Determine the steam consumption at 63% load, kg/hr.
Finding mas flow rate, in lb/s, and exit temperature in F. Step by step solution please thank youuu
Superheated steam at 18 MPa, 560 °C enters the steam turbine. The pressure at the exit of the turbine is 0.06 MPa and saturated liquid water leaves the condenser at 0.06 MPa. Pressure is increased to 18 MPa again after the pump. Find: (a) Sketch the process on a T-s diagram. (b) The net work per unit of steam flow in kJ/kg. (c) Heat transfer to steam passing through the boiler, in kJ/kg.
I need help with a review porblem I cannot solve! thank you Steam enters an adiabatic turbine at 4 MPa, 800K and exits at 8 kPa, 90% quality. Assuming steady state, steady flow conditions, determine: a) The power output of the turbine (MW) if the mass flow rate is 63kg/s. b)The volumetric flow rate at the inlet (m3/s).
Water vapor enters an adiabatic turbine at a pressure of 8 MPa, a temperature of 600 ℃ and a speed of 100 m/s, and then a pressure of 50 kPa exits at a temperature of 150 ℃ and a speed of 160 m/s. The turbine power is 10 MW. According to this; a) The steam flow rate from the turbine b) Do you find the isanthropic efficiency of the turbine?
A steady stream of steam passes through an adiabatic turbine. It enters at 10 MPa, 450 °C and 80 m/s and at the exit it is 500 KPa, 40% quality and 30 m/s. The mass flow of the steam is 12 kg/s. a) With the power that comes out of the system, 252 100 W bulbs can be lit. Calculate the efficiency of the system. b) What is the area of the duct at the entrance? c) What is the volumetric flow at the outlet? d) What is the temperature of the steam at the outlet?
Thermodynamics Instructions: Answer the problem Determine Its: a) combined work b) combined heat rate c) total throttle flow for the rated power *show complete solutions and please write legibly. TY
Example dulmalek Air enters the compressor of an ideal air-standard Brayton cycle at 300K. the compressor ratio is 8 and the turbine inlet temperature is 1300K. Determine: a) The gas temperature at the exit of the compressor and the turbine. b) The back work ratio. c) c) The thermal efficiency. Assume the compressor efficiency of 80 percent and the turbine efficiency of 85 percent. d) The thermal efficiency of the gas-turbine power plant if generation having an effectiveness of 80 percent is installed. Shay
The turbine section of a Brayton cycle receives hot compressed air at 150 psia, 2100 R, expands it to 15 psia and develops a gross output of 15,000 HP. Air enters the compressor section at 15 psia, 500 °R. Determine: a) mass of air required (Ib./s), b) compressor power required (HP), c) Net power output (HP), d) thermal efficiency.
Steam enters a turbine at a mass flow rate of 1.4 kg/s, a pressure of 700 kPa and a temperature of 400 °C. Steam comes out of the turbine at a pressure of 100 kPa and a specific volume of 1.4 m3/kg. Since the heat transfer from the turbine to the environment is 50 kW, the boundary temperature between the turbine and the environment is 70 °C,a) Find the power produced by the turbine.b) Calculate the entropy produced in the turbine.c) Find the isentropic efficiency of the turbine.Note: Changes in kinetic and potential energies will be neglected and T (K) = 273 + °C will be taken.
2. A two-stage air compressor has an intercooler between the two stages as shown below. The inlet state is 100 kPa, 290 K, and the final exit pressure is 1.6 MPa. Assume that the constant pressure intercooler cools the air to the inlet temperature, T= T1. It can be shown that the optimal pressure, P,= (P.Pa for minimum total compressor work. Find the specific compressor works, the intercooler heat transfer for the optimal P, and sketch and label the P-v and T-s diagrams. otf Corpressor Compressor Intercooler

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS