11. The specified dimension 225.00 mm for a certain injection molded part made of ABS. What is the corresponding dimension to which the mold cavity should be machined? Your answer is: . 12. The description of the repeatability of an experiment is called. 13. Which of the following bulk deformation processes are involved in the production of nails for lumber construction: a. bar and wire drawing c. impression die forging, b. extrusion d. rolling

11. The specified dimension 225.00 mm for a certain injection molded part made of ABS. What is the corresponding dimension to which the mold cavity should be machined? Your answer is: . 12. The description of the repeatability of an experiment is called. 13. Which of the following bulk deformation processes are involved in the production of nails for lumber construction: a. bar and wire drawing c. impression die forging, b. extrusion d. rolling

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

As the lead engineer for a LPG storage project, you are overseeing the design of pressure vesselssuch as those shown below. Identify which test (or tests) is mostsuitable to pick a material and thickness for the spherical shell of the pressure vessel. Why these are the relevant tests. Explain what information these tests provide and why it is important to determining material and thickness.
A new sintering regime is proposed for producing Alumina acetabular liners for total hip replacement. If the alumina has a plane strain fracture toughness of 2.7 MPa.mº.5, an ultimate tensile strength of 307 MPa and Y is assumed to be 1.2, which of the following would be the maximum acceptable size of surface flaw? Select one: Ⓒa. 4.8 μm O b. 9.6 μm O c. 19.2 μm O d. 2.4 μm
Question 2 The following data relate to an injection moulding grade of a thermoplastic polymer. Determine whether this melt obeys the power law and if so, estimate the power law exponent n. Comment on your findings. Shear rate (s') Viscosity (Pa.s) 10 2590 100 2260 500 1370 1000 845 2000 525 5000 278 10000 175
why is the answer B?
The figure shown below (Fig. 2) is a schematic representation of a scissor jack in two different positions. The maximum load that this mechanism must withstand is 800 kg. 4 are proposed different materials to make the jack arms and spindle. The mechanical properties and some Physical characteristics of each material are shown in Table 1. a) Based on the properties of each material and the cross section of the arms and the screw, Propose what would be the most suitable material for its manufacture. The length of each arm is 150 mm. The stress on the arms and the spindle must not exceed the yield strength of the material selected for neither of the two analysis positions. b) Using the mechanical properties of the material you selected, calculate the change in dimension that the arms and the spindle of the jack were tested for the two analysis positions. The length of the spindle is 280 mm.
Q1:T shaped Mild Steel beams are widely used in structural fabrication activities, examine the shown M.S. Beam and with required sketches explain how it can be manufactured.
4. A manufacturing engineer would like to carry out an exercise to identify the source/s of the variations when measuring the length of plastic injection moulded part. a) Guide the engineer through the process which needs to be carried out. b) The preliminary findings obtained from the exercise are as follows: EV = 0.20, AV = 0.07, PV = 0.90. Complete the calculations to obtain the final results. c) What do the final results mean? d) How would the engineer know whether the produced parts are acceptable or not? e) What would you suggest to minimise the variations? solve part a b c in 30 mins i will give thumb up thanks
Compute individual percent retained, cumulative percent retained and percent passing. Make a particle size distribution chart using semi log using excel. Compute the fineness modulus of the sample. Identify whether weight percent within the governing specs passed.
ACE Metals produces and machines titanium castings for aircraft components. A critical dimension is the diameter of the component that must be inserted into another fuel delivery assembly. The specification is 0.850 ± 0.050 inch. What are the values for the Lower Spec Limit and the Upper Spec Limit? Show your work below.
10. A bar of 30 cm diameter is subjected to a pull of 200 kN. The measured extension on gauge length of 3.50 m is 5 cm and change in diameter is 2 mm. Calculate: (i) Young's Modulus, (ii) Poisson's Ratio (iii) Bulk Modulus and (iv) Shear Modulus.
If the wrought stock material costs $60 per kg, what is the lost value due to the material removed, assuming scrap is sold for $3 per kg? Assume the density of titanium is 4.5 g/cm3. Briefly explain how you got your answer. Neglect costs of lubricant/coolant, chip handling, etc. Round your answer down to the nearest dollar.