If the material is copper & Sut=281 Mpa. Find (So) if:(a) the load is axial (b) the load is Torsion (c) the load is bendingFind Cload if:(a) the load is axial (b) the load is Torsion (c) the load is bendingIf the load is axial Find Csize if:(a)120 mm(b) d=0.29 in(c) d=7mm(d) d=240mm98- If Sut-441 Mpa. Find C surface if the surface finish is:(a) Ground (b) Hot rolled9- If Sut=75 kpsi. Find C surface if the surface finish is:(a) Ground (b) cold rolled10- Find C Temp if:(a) Iron & T=820° F (b) Titanium & T=820° C11- Find (Sn), if: N=5* 107, the material is copper, Su=420 Mpa, So= 378 Mpa, Sf = 222 pa.12- Find S.F) fatigue if:Uniaxial fully reversed:Sn = 200 Mpa, ox max =30 Mpa, ox min = - 30 Mpa13- Find S.F) fatigue if:Multiaxial repeated:Sn 200 Mpa, a yield =600Mpa, aut 900Mpaox max =30 Mpa, ox min = 0 Mpaay max=0 Mpa, ay min=-40MpaDay 13 Mpa constant (static)

Answered: Image /qna-images/answer/0075ce1e-9ea7-4a54-a1e6-b38c050f92bf.jpg

Answered: If the material is copper & Sut=281…

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.7.7P: A bar of monel metal with a length L = 9 in. and a diameter d = 0225 in. is loaded axially by a...

See similar textbooks

Similar questions

A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?
A round bar of 10 mm diameter is made of aluminum alloy 7075-T6 (see figure). When the bar is stretched by axial forces P, its diameter decreases by 0.0 16 mm. Find the magnitude of the load P. Obtain the material properties from Appendix 1.
A copper rod of length L = 18.0 in. is to be twisted by torques T (see figure) until the angle of rotation between the ends of the rod is 3.0°. (a) If the allowable shear strain in the copper is 0.0006 rad, what is the maximum permissible diameter of the rod? (b) If the rod diameter is 0.5 in., what is the minimum permissible length of the rod?
A steel wire- and an aluminum allay wire have equal lengths, and support equal loads P (see figure). The moduli of elasticity for the steel and aluminum alloy are Ea= 30,000 ksi and Ea= 11,000 ksi, respectively. (a) IF the wires have the same diameters, what is the ratio of the elongation of the aluminum alloy wire to the elongation of the steel wire? (b) If the wires stretch the same amount, what is the ratio of the diameter of the aluminum alloy wire to the diameter of the steel wire? (c) If the wires have the same diameters and same load P, what is the ratio of the initial length of the aluminum alloy wire to that of the steel wire if the aluminum alloy wire stretches 1.5 limes that of the steel wire? (d) If the wires have the same diameters, same initial length, and same load P. what is the material of the upper wire if it elongates 1.7 times that of the steel wire?
Solve the preceding problem for sx= 11 MPa and ??y= -20 MPa (see figure).
,10-6 A prismatic bar with a diameter d0= 20 mm is being compared with a stepped bar of the same diameter(d| = 20 mm) that is enlarged in the middle region lo a diameter d2= 25 mm (see figure). The radius of the fillets in the stepped bar is 2.0 mm. (a) Does enlarging the bar in the middle region make it stronger than the prismatic bar? Demonstrate your answer by determining the maximum permissible load for the prismatic bar and the maximum permissible load F, for the enlarged bar, assuming that the allowable stress for the material is 80 MPa. (b) What should be the diameter d0of the prismatic bar if it is to have the same maximum permissible load as does the stepped bar?
A copper wire having a diameter ofd = 4 mm is bent into a circle and held with the ends just touching (see figure), If the maximum permissible strain in the copper is = 0.0024, what is the shortest length L of wire that can be used? If L = 5.5 m, what is the maximum acceptable diameter of the wire if the maximum normal strain must remain below yield? Assume E = 120 GPa and(7K= 300 MPa.
A vertical bar is loaded with axial loads at points B, C, and D. as shown in the figure. The bar is made of steel with a modulus of elasticity E = 29,000 ksi., The bar has a cross-sectional area of 8.24 in2. Calculate the displacements at points B, C, and D. Ignore the weight of the bar
Three prismatic bars, two of material A and one of material B. transmit a tensile load P (see figure). The two outer bars (material A) are identical. The cross-sectional area of the middle bar (material B) is 50% larger than the cross-sectional area of one of the outer bars. Also, the modulus of elasticity of material A is twice that of material B. (a) What fraction of the load P is transmitted by the middle bar? (b) What is the ratio of the stress in the middle bar to the stress in the outer bars? (c) What is the ratio of the strain in the middle bar to the strain in the outer bars?
A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in the figure. The roof load P:equals 400 KN, and the second-floor load P-, equals 720 kN. Each column has a length L = 3.75 m. The cross-sectional areas of the first- and second-floor columns are 11,000 mm" and 3900 mm", respectively. (a) Assuming that E = 206 GPa. determine the total shortenings aof the two columns due to the combined action of the loads Ptand P,. (b) How much additional load P0can be placed at t he top of t he column (point C) if t he total shortening: SACis not to exceed 4.0 mm?
An aluminum bar subjected to tensile Forces P has a length L = 150 in. and cross-sectional area A = 2.0 in2 The stress-strain behavior of the aluminum may be represented approximately by the bilinear stress-strain diagram shown in the figure. Calculate the elongation S of the bar for each of the following axial loads: p = 8 kips, 16 kips. 24 kips, 32 kips, and 40 kips. From these results, plot a diagram of load P versus elongation S (load-displacement diagram).
A bar AB of length L and weight density y hangs vertically under its awn weight (see figure). The stress-strain relation forth? Material is given by the Romberg-Osgood equation [Eq. (2-71)]: Derive the formula For the elongation of the bar.

SEE MORE QUESTIONS

Recommended textbooks for you

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS