1-3 . Answer it correctly and this is Asap I will rate helpful if fast and perfect 1) How many Millimeters are in 23/64a) 9.13 mmb) 8.98 mmc) 7.47 mmd) 9.24 mm2) When drilling for a 1/2" socket head Cap Screw, what size hole would you drill for a Counterbore?a) 0.500b) 0.530c) 0.480d) 0.6253) How many Inches are in 18 Millimetersa) 7.086 inchesb) 0.7086 inchesc) 0.079 inchesd) 7.860 inches

1) How many millimeters are in 23/64? You are asked to convert 23/64 inches into millimeters.…

Answered: 1) How many Millimeters are in 23/64 a)…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1) How many Millimeters are in 23/64 (Go to the fifth decimal point) a) 9.13 mm b) 8.98 mm c) 7.47 mm d) 9.24 mm 2) When drilling for a ½" socket head Cap Screw, what size hole would you drill for a Counterbore? a) 0.500 b) 0.530 c) 0.480 d) 0.625 3) How many Inches are in 18 Millimeters a) 7.086 inches b) 0.7086 inches c) 0.079 inches d) 7.860 inches 4) What does 2A represent for 3/8-16 UNC-2A thread a) Outside Diameter of Screw b) 16 Threads per inch c) Fine Tread of a Screw d) Thread Tolerance
4-6
41. A semicircular tunnel has a base diameter of 30 ft. How high is the tunnel 9 feet from the center of the road? A) 11 ft B) 8 ft C) 9 ft. D) 12 ft
What is the angle of twist for a 2 ft. diameter aluminium bar if it is subjected to a torque of 10,000 ft-lb? The length of the aluminium bar is 6 ft and the modulus of rigidity is 3.7 x 106 psi. A)0.0312 degrees B)0.0107 degrees C)0.0041 degrees D)0.00646 degrees
24- A cup is to be drawn in a deep drawing operation. The height of the cup is 75 mm and its inside diameter 200 mm. The sheet metal thickness = 6 mm. If the blank diameter = 300 mm, determine the reduction. a) 0.333 b) O 0.010 C) 0.030 d) 0.500 e) 0.020 f) O 0.040 g) 0.200 h) O 0.250
MENG104 Mechanical workshop practice Please dont late
9 - A power shears is used to cut soft cold rolled steel that is 4.75 mm thick. At what clearance should the shears be set to yield an optimum cut? a) 0,525 b) 0,656 C) 0,405 d) 0,356 e) 0,575 f) 0,285
What is the radius of gyration of a hollow rectangle with base = 3 mm, height= 6 mm and a 0.50 mm thickness? a) 1.7045 mm b) 2.0361 mm c) 7.4424 mm d) 9.9942 mm
A shaft and hub with a nominal diameter of 4.730 inches are designed with a running clearance fit (RC3). The inside diameter of the hub should measure no larger than? a) 4.6987 in b) 4.7076 in c) 4.7104 in d) 4.7314 in e) 4.7599 in f) 4.7645 in
5) Reaming is a process of enlarging a hole to obtain a precise hole diameter and good surface finish. a) True b) False 6) Cutting Speed is expressed as a) Surface feet per second b) RPM c) Inches per minute d) Surface feet per minute 7) Reaming is a process of a) Cutting threads in a Workpiece b) Making a precise hole in a Workpiece c) Making shape for a Socket flathead cap screw in a Workpiece d) Making shape for a Socket head cap screw in a Workpiece. 8) Tapping is a process of a) Cutting threads in a Workpiece b) Making precise hole in a Workpiece c) Making shape for a Socket Flathead cap screw in a workpiece d) Making shape for a Socket head cap screw in a Workpiece
21 - A vertical cylindrical vessel with a diameter of 15 cm and a height of 40 cm is partially filled with 25 cm high water. The cylinder is rotated at a constant speed of 20 rad/s. What is the maximum height difference between the edge and the center of the free surface? a) 11.5cm B) 15cm NS) 5.4cm D) 9.5cm TO) 7.2cm 22 - The water level in a tank is 9.4 m above the ground. At the bottom of the tank, the sprinkler connected to the pipe end faces upwards. The effective pressure at the water surface inside the tank is 300 kPa. Since the system is at sea level, how high does the water coming out of the fountain rise? (ρ=1000 kg/m³) a) 48 meters B) 25m NS) 30m D) 40m TO) 20m
A rack is made from roll-formed sheet steel and has the cross section shown. Determine the location (x, y) of the centroid of the cross section. The dimensions are indicated at the center thickness of each segment. y -30 mm- 5 A) 15 mm 4 B) 7,5 mm 80 mm C) 0 mm 50 mm D) 5 mm 1 7 E) 10 mm 15 mm 15 mm 2KL 15* x, +50* x, +15*x, + 30 * x +30 *: x; +80* x6+15 *x, X = 235 X3 = ? 3. 2.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS