MENG104 Mechanical workshop practicePlease dont late 17-The surface roughness is shown with a symbol.....a) Rab) Rsc) Rcd) Rq18- The largest diameter of the bolt is called the... diameter.a) majorb) Minorc) Pitchd) Root19- The tip angle of the twist drill is ... degree.b) 90......a) 60c) 118d) 12020- Calculate the rpm required to drill 10 mm diameter hole on a workpiece. (CS 20 m/min)a) 305b) 452c) 560d) 70521- Evaluate the tap drill size for the UNC 1/2"x 13a) 0.426"b) 0.423"c) 0.420"d) 0.417"22- Evaluate the tap drill size for the BSW 1/2"x 12a) 0.417"b) 0.423"c) 0.420"d) 0.426"23- Evaluate the tap drill size for the M12 x 1.5a) 10.0b) 10.5c) 11.0d) 11.5

As it is not mentioned that which three parts required to solve, please find the solutions of first…

17-The surface roughness is shown with a symbol.... a) Ra b) Rs c) Rc d) Rq 18- The largest diameter of the bolt is called the... diameter. a) major b) Minor c) Pitch d) Root 19- The tip angle of the twist drill is .... degree. a) 60 b) 90 c) 118 d) 120

17-The surface roughness is shown with a symbol.... a) Ra b) Rs c) Rc d) Rq 18- The largest diameter of the bolt is called the... diameter. a) major b) Minor c) Pitch d) Root 19- The tip angle of the twist drill is .... degree. a) 60 b) 90 c) 118 d) 120

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

It is a from of practical on-the -job training given under the direction of skilled mechanics or technicians [a educator (b)apprentice (c)rider (d)debater
5. How do point loads and uniform distributed load be represented in SFD? a) Horizontal lines and curved lines b) Curved lines and inclined lines c) Horizontal lines and inclined lines d) Cant represent any more
.
AMNT 280 Assignments 1-4 Media Presentation Categories Of Reciprocating Engines Develop a Media Presentation develop a power point media presentation Presentation will require researching a module specific topic For this activity you will research the four categories of reciprocating engines In your presentation address the following: 1 Research the four different types of reciprocating engines2 Provide an overview of the design, construction, and firing order of each engine 3 Provide research concerning which air frame used the engine Presentation Guidelines Note:This information applies to all Media Presentation activities and will not be repeated Present your research material in the format of a written document (Introduction, body, and conclusion) Presentation requirements consist of 5-7 slides with a balance of both bullet text information and images; does not include the title or reference slide APA formatting and structural guidelines apply Additional information…
18 - Which of the following judgments has been given incorrectly for glasses?A) Glass in molten or liquid state has a high viscosity.B) Glass is a hard and solid material to the touch.C) The main ingredient of glass is silicon dioxide.D) Viscosity of glass in liquid state at 1000 0C is higher than the densest oil.E) The viscosity increases gradually when the glass is heated and decreases gradually when it is cooled.
1) Prof. K. climbed a wall and is now stuck and hungry. One of her ME 242 students saw this opportunity to test one of their pulley mechanisms to lift some pizza boxes for Prof. K. If the student is pulling the free end with a velocity of 2.75 ft/s. a) What is the mechanical advantage between the student and the pizza boxes? Hint: The link between pulleys 1 and 4 is rigid (meaning that they must move together. This is the key to solving this problem! b) What is the velocity of the pizza boxes? Be sure to indicate which direction it is moving. [Ans. to check: 1.375 ft/s] PizzA 49°F Sunny O 4x 99+ P Type here to search End PgUp PgDn PrtScn Home
10:13 Question 8 of 16 Which of the following processes is spontaneous? A) Heat coming out of an open oven. B) A puddle evaporating in the sun. C) A car rusting. D) Water turning into ice in a freezer. E) All of the above Tap here or pull up for additional resources Submit
PROBLEM 1 For the engineering activity, current practical capacity is defined by the following requirements: 6,000 engineering hours for each product group that has been on the market or in development for 5 years or less, and 2,400 hours per product group of more than 5 years. Four product groups have less than 5 years' experience, and 10 product groups have more. There are 24 engineers, each paid a salary of P60,000. Each engineer can provide 2,000 hours of service per year. The actual engineering usage was 46,000 hours. The standard is 58% of current practical activity capacity. Case 1: Calculate the (1) activity volume and (2) unused capacity variances for the engineering activity Case 2: Suppose the operational managers have selected some improvement measures that promise to reduce non-value-added activity usage by 40% in the following year. Using the targeted reduction, establish kaizen standards for engineering, expressed both in physical and financial measures
Quèstion 10 In. maintenance staffing properly-skilled individuals combine the company's supervisors for maintenance activities. Combined In-House/Contract Contract Maintenance Complete In-House Complete Contract Maintenance
Engineering Materials
Question 8 The following term is not relevant to project life cycle Select one: O a. Synthesis O b. Planning O C. Concept O d. Feasibility analysis
What is productivity index and write short note on it?