5. A 5m-long bar AB is supported by a ball-in-socket support at A, the cable CD and a smooth floor at B. A force F = -10 i (N) is applied at G. Here, D is at the midpoint of the bar AB, G is the midpoint of AD, and C is the midpoint of OE. Here, the line BE is parallel to x-axis. Neglect the weight of bar AB. Use the scalar method to determine the tension in cable CD and the reactions at A and B. (Hint: you can break the tension force by cable DC to its components.) (F-9.015N, FB=3.75N, 4, 5N, A, ON, A==3.75N). x 3m

5. A 5m-long bar AB is supported by a ball-in-socket support at A, the cable CD and a smooth floor at B. A force F = -10 i (N) is applied at G. Here, D is at the midpoint of the bar AB, G is the midpoint of AD, and C is the midpoint of OE. Here, the line BE is parallel to x-axis. Neglect the weight of bar AB. Use the scalar method to determine the tension in cable CD and the reactions at A and B. (Hint: you can break the tension force by cable DC to its components.) (F-9.015N, FB=3.75N, 4, 5N, A, ON, A==3.75N). x 3m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.97P: The figure shows a wire cutter. Determine the cutting force on the wire at A when the 75-N forces...

See similar textbooks

Similar questions

For the ladder in Prob. 6.17, find the internal force system acting on section 2, assuming that x < a/2.
The figure shows a wire cutter. Determine the cutting force on the wire at A when the 75-N forces are applied to the handgrips. (Hint: The horizontal components of pin forces at B and D are zero due to symmetry.)
Find the internal force system acting on section 3 for the pin-connected frame.
Find the magnitude of the pin reaction at B caused by the weight W=80lb. Neglect the weights of the members.
Solve the preceding problem for the following data: b = 6 in., b = 10 in, L = 110 ft, tan a = 1/3, and q = 325 lb/ft.
4. The access door in Fig. P6-13 is held in the position by cable AB. If the magnitude of tension T in the cable is 50 pound force, find the rectangular components of T acting at A. 10 in. B 10 in. 12 in. 6 in. 20° FIGURE P6-13
Q4: of a car غطاء محرك The i Jul. The bonnet is held open at an angle of 60° to the horizontal by a vertical force V applied at one end of the bonnet (shown on the diagram). The long, has a weight of 25 N and its center diagram shows the open bonnet bonnet is 0.90 m of gravity G is 0.35 m from the hinge at O. 1) On the diagram, draw and label the two forces other than V acting on the bonnet. By taking moments about A, Proof that the vertical 2) force V applied at the end of the bonnet is 9.7 N. 3) Calculate the magnitude of the force acting at the hinge ON.
A 400 N gas sign hangs from the end of a uniform strut BC. The strut is 4 m long and weighs 600 N. The strut is supported by a hinge at the wall at C and by a cable whose other end is tied to the wall at point A 3.0 m above the left end of the strut. Find the tension in the supporting cable and the force of the hinge on the strut. 5.0 m 3.0 m 4.0 m B GAS TAB= 1333 N TAB= 1167 N TAB= 400 N TAB= 1000 N leave the question 4 Other: Q 4 4 points Rc= 980 N O Rc= 360 N Rc= 890 N Rc= 1085 N O O O O O O O
A uniform rigid disk has mass "M" and radius "a", and a rigid uniform rod has mass "m" and length "b". The bar is located along the vertical axis of symmetry of the disk with one end in contact with the disk. Find the force required to separate the bar from the disk. The bar is on the disk.
A hydraulic crane of total mass (including the mass of the boom) 53O0kg supports a load of 800kg. The boom mass 500kg is 7m long and makes an angle of 50 degrees with the horizontal. The boom's center of the boom length. Also assume that the center of mass of the crane excluding the boom acts at the middle of the outrigger jacks that are 4m apart. Draw the FBD of the crane and boom. Find the reaction force at the rear outrigger jack (Nr) and at the front (Nf) for the system to be in equilibrium. Assume the ground is friction less. 7m 1m
Parallel Forces in Space. Show complete solution
The wheels, axle, and handles of a wheelbarrow weigh W = 55 N. The load chamber and its contents weigh WL = 623 N. The drawing shows these two forces in two different wheelbarrow designs. To support the wheelbarrow in equilibrium, the man’s hands apply a force to the handles that is directed vertically upward. Consider a rotational axis at the point where the tire contacts the ground, directed perpendicular to the plane of the paper. Find the magnitude of the man’s force for both designs.