Apply the necessary symbology to establish the required tolerance and datum features to control the circular runout of the .375 diameter cylinder to a value of .006 relative to an axis established by the two .250 diameter bearing surfaces.

Apply the necessary symbology to establish the required tolerance and datum features to control the circular runout of the .375 diameter cylinder to a value of .006 relative to an axis established by the two .250 diameter bearing surfaces.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Refer to the figure below. What is the MMC, LMC and geometric tolerance for the Hole and Pin: a. Hole: MMC LMC Geom. Tol. b. Pin: MMC LMC Geom. Tol. C 1.000 1 1.000 Ø.515-.540 Hole +0.010@ABC 1.000 B Ø.495-.500 Pin 0.005MABC A
Perpendicularity tolrance that results in a virtual condition for pin/hole.
Given a pin with a size dimension of Ø.875±.003 and a perpendicularity tolerance of .002 at MMC to a primary datum, what is the boundary that takes into consideration the combined effect of feature size at MMC and the geometric tolerance? .870 .874 .876 .880
If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance? C 1.000 Y 1.000 .005 .500 .003 O .498 .007 Ø.515-.525 0.010MABC 1.000 B Ø.498-.500 0.005MABC A
Given a hole with a size dimension of Ø.875±.003 and a positional tolerance of.002 at MMC, what is the boundary that takes into consideration the combined effect of feature size at MMC and the geometric tolerance? .870 .874 .876 .880
Question 5 Assuming there is no wheel slippage, what is the wheel rotation speed in revolutions per minute of a car moving in a straight line at constant speed for 5 min over a distance of 181 m? The wheels have a diameter of 450 mm. Give your answer in meters rounded to two decimal places, use PI = 3.14. Do not write the unit in your answer.
5. When verifying flatness, the feature of size is first measured to verify that it falls within the O two parallel lines O bowed surface tolerance zone O size limits
Specify a circularity tolerance of .001 for the conical taper on the part in the drawing below. A. .001 B. C. D. O A B .001 .001 .001 Ø4.000-4.002
What part provides the most manufacturing tolerance and is easiest to work with, part 1 or part 2? Explain why.
I need help solving problem numbers 4--15.
6. On an engineering drawing a dimension is laid out as 1.760 + 0.005 A note on the drawing states that all dimensions are in inches. Give numerical values for (a) The nominal dimension (b) The upper limit (c) The tolerance (d) The bilateral tolerance
Apply geometric tolerancing to part according to the instructions below. This exercise will provide you with experience in correctly applying and interpreting geometric tolerancing symbology. If you have trouble applying the symbols, page through this unit looking for similar examples. The Hole Bar in this unit is a good reference. Draw symbols and feature control frames clearly and neatly. 1. Establish the right face in the side view as datum feature A. Qualify this feature with a flatness of .005. 2. Establish the top surface in the front view as datum feature B. Qualify this feature with a perpendicularity of .005 to datum feature A. 3. Establish the left surface in the front view as datum feature C. Qualify this feature with a perpendicularity of .005 to datum features A and B. 4. Establish all necessary dimensions as basic. 5. Position the .250 hole within a diameter of .005 RFS relative to datum features A,B,C. 6. Position the three holes within a diamter of .012 at MMC relative…