ne 1/2-inch diameter pin in the drawing below is required to be perp ature A within tolerance of .002 at MMC. Provide the appropriate feature control fr -quirement.

Q: Check the correct fit: This is a clearance (), transition (). interference ( ) fit.

A:

Q: Pin: MMC LMC Geom. Tol. с 1.000 1 1.000 Ø.515-.540 Hole 0.010M ABC 1.000 B Figure for Problem 21…

A:

Q: FIND THE CUBIC SPLINE G(x) for the given data k0 and kn as given 12. fo=f(0) = 1, ₁ = f(2)=9,…

A:

Q: A specifeid hole diameter of min and max has specified tolerance at LMC. A produced hole of diamter…

A: Introduction: Tolerances in mechanical engineering define the permissible variation from specified…

Q: The Boss is created at 59.88, what is the allowed Position Tolerance?

A: Given data as per question Basic size of the boss =60

Q: On the part shown, specify a paralellism tolerance to make the top surface parallel to datum A…

A:

Q: If the tolerance in the figure below is for a pin .525 in diameter, what is the total positional…

A:

Q: I need help with question number 15 that is pertaining to the print provided.

A: 15.The unidirectional system is used here for the dimension placing. The unidirectional system is…

Q: I have a pin with a Diameter of 10.00/9.95. What is the Maximum Bow of this pin?

A: bow in pin:-

Q: A journal bearing has a shaft diameter of 70.00 mm with a unilateral tolerance of-0.02 mm. The…

A:

Q: 1. Determine the tolerance allowed on the hole of the part.

A: Tolerance – the total allowable change in measurement; the contrast between the upper and lower…

Q: What is the width of the groove on the bolt?

A: Given :- Bolt drawing Find :-  Width of the groove on the drawing = ?

Q: 3. If the tolerance applies at MMC then a possible O indeterminant bonus O LMC zero tolerance…

A: given = fill in the blanks

Q: 5. If the pin in the figure below were produced at a diameter of 1.004 and toleran the feature…

A: Given  Pin produced at diameter=∅1.004  And∅1.000-1.010

Q: Sketch a setup and measurement method that may be used to check the runout tolerance. Also show the…

A: To sketch a setup and measurement method to check runout tolerance. and to show acceptable max…

Q: |Complete a feature control frame that specifies a circular runout tolerance of .008" relative to an…

A: The datum is the locus surfaces or the initial points for the position and alignment of features of…

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance? C…

A: Given data as per the question Pin diameter =0.498

Q: Identify the GD&T applicable for the following component assembly. Make a table including Tolerance…

A: Given:To find:Identify the geometric dimensioning and tolerancing (GD&T) applicable.

Q: 20 BUTT-2A .688 R. .626 DIA..003 5.50 13 812 6.000 -1.000 UNLESS OTHERWISE SPECIFIED: MATERIAL:…

A: 5. Pitch  6. BUTT is designation for  9. Standard or precision class of fit

Q: Complete feature control frame that controls perpendicularity of the hole to .012" diameter at MMC…

A:

Q: I need help solving problem numbers 4--15.

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: The toleranced diameter of a hole is given as 0.990"/1.010" and the size of the mating pin is given…

A: Given data: -  The tolerance diameter of hole is Dh = 0.990"/1.010".  The tolerance diameter of pin…

Q: plete the hole specification including a position tolerance of C ary datum feature A, secondary…

A: Given-Information:- To-Determine:- Complete hole specification

Q: Need solution to both questions.

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.