b. A square screw thread is connected to a block with a belt passing over three cylinders. The clamp has square threads with a radius, r = 0.47 in., a lead, L = 0.38 in., and a coefficient of friction of the threads is μs = 0.38. What is the moment on the clamp necessary to raise the block to raise if W = 76 lb ? W Two blocks are stacked as shown. If the weight of the blocks are. W198 lb and W2 = 169 lb respectively. and the dimensions are, a 4.8 ft.. and b = 5.6 ft.. and the coefficients of static friction are. Ms1 = 0.43 and μs2 = 0.1. What is the minimum force, P, required to reach impending motion? Make sure to check all impending motion cases. P b W₁ "sl W₂

b. A square screw thread is connected to a block with a belt passing over three cylinders. The clamp has square threads with a radius, r = 0.47 in., a lead, L = 0.38 in., and a coefficient of friction of the threads is μs = 0.38. What is the moment on the clamp necessary to raise the block to raise if W = 76 lb ? W Two blocks are stacked as shown. If the weight of the blocks are. W198 lb and W2 = 169 lb respectively. and the dimensions are, a 4.8 ft.. and b = 5.6 ft.. and the coefficients of static friction are. Ms1 = 0.43 and μs2 = 0.1. What is the minimum force, P, required to reach impending motion? Make sure to check all impending motion cases. P b W₁ "sl W₂

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A jack having square threads of 50 mm nominal diameter and 10 mm pitch is supporting a load of 89 kN. A double thread is used and the coefficient of friction maybe as low as 0.10 or as high as 0.15.a. Will this screw always self-locking?b. What is the highest torque necessary to raise the load?
Information about the clamp assembly in the figure is given below. Thread diameter 12 mm, root diameter 10.16 mm, pitch 1.5 mm, screw profile angle 2α=60, friction surface of table A diameter 10 mm, friction between plate A-screw end surface coefficient 0.15 and screw-nut friction coefficient 0.15 is given. If a hand force of 200N is applied to the vise arm, if applied, a) How much force is applied to the clamped part. b) Calculate the efficiency of the vise.
1. A jack having square threads of 50 mm nominal diameter and 10 mm pitch is supporting a load of 89 kN. A double thread is used and the coefficient of friction maybe as low as 0.10 or as high as 0.15.a. Will this screw always self-locking?b. What is the highest torque necessary to raise the load?c. What maximum torque is necessary to lower the load?d. What is the maximum torsional shear stress induced on the screw?
4.) A flat belt makes contact with an 16 in. diameter pulley through half its circumference. If the coefficient of friction is 0.45 , and a torque of300ft−bsis to be transmitted, calculate the belt tensions. (please type answer not write by hend)
Problem: A double-threaded power screw with ISO metric trapezoidal threads is used to raise a load of 300 kN, The nominal diamter is 100 mm & the pitch is 12mm. The coefficient of friction at screw threads is 0.15. Neglect the collor friction. Q.45 Torque required to raise the load is
Question 3 A single square thread power screw is to raise a load of 50 KN. A screw thread of major diameter of 34 mm and a pitch of 6 mm is used. The coefficient of friction at the thread and collar are 0.15 and 0.1 respectively. If the collar frictional diameter is 100 mm and the screw turns at a speed of 1 rev/s. (Given dm = 31mm, 1 = 6mm, dc = 100mm). Find: (a) the power input to the screw. (b) the combined efficiency of the screw and collar.
A single square thread power screw has a lead of 7 mm and mean diameter of 35 mm. If it Is used to lift a load of 30 kN and coefficient of friction of thread is 0.18, find the torque required to turn the screw.
4.) A flat belt makes contact with an 18 in. diameter pulley through half its circumference. If the coefficient of friction is 0.45, and a torque of 350 ft-lbs is to be transmitted, calculate the belt tensions.
(5) A 2½-in square thread steel screw is used in a common jack screw. There are 2¼TPI. The body of the jack is made of cast iron. The coefficient of friction on the threads is 0.15. The thrust collar at the top has an inside diameter of 1½-in & the outside diameter of 3.0in. The coefficient for the collar is 0.25. The load to be lifted by the jack screw is 2 tons. Determine: (a) the efficiency of the screw only; (b) the efficiency of the screw & the thrust collar; (c) the pull necessary @ the end of a 2.0ft lever to operate this screw jack.
thick lnange be! The total torque required to turn the double threaded power screw is 55 N.m. If the screw turns at 285 rpm and the pitch of 4mm, find: A. The horsepower input of the power screw. B. The efficiency if the weight loaded is 10 kN.
A vertical power screw with double start square threads of 50 mm mean diameter and 11mm pitch is raised against a load of 10 kN by means of a hand wheel, the boss of which is threaded to act as a nut. A thrust collar, taking up the axial load,supports the wheel boss and has a mean diameter of 60mm. The coefficient of friction is 0.18for the screw and 0.16for the collar. If the tangential force applied by each hand to the wheel is 200 N, find suitable diameter of the hand wheel.
A square threaded power screw has an efficiency of 65% when raising the load. The coefficientof friction for the threads is 0.15, with the collar friction negligible. Determine the lead angle of thescrew.