Which of the following statements below are incorrect? select all which apply.     A shear force diagram is a diagram of extermal force along the beam      a bending moment diagram is a diagram of internal bending moment along the beam caused by external loading     a bending moment diagram is a diagram of external moment along the beam     Shear force diagram could be considered as a function of beam load diagram as dV/dx = w, where V and w are internal shear force and external force density of the distributed force at one point along the beam, respectively.     Bending moment diagram could be considered as a function of shear force diagram as dM/dx = V, where M and V are internal bending moment and internal shear force at one cross-section along the beam, respectively.     A shear force diagram is a diagram of internal shear force along the beam caused by external loading

Q: + y -250 N 2-2) R. 350 N 70° - X 60° 80° 145 N 180 N DIAGRAM OF FORCES AND THEIR ANGLES WITH THE…

A:

Q: The bending moment M of a beam of length 1 at one end is given by M = Wx(1 - x)/2, where length.…

A:

Q: The basic differential equation of the elastic curve for a simply supported, uniformly loaded beam…

A: Differential equation is:where:

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: Given condition: The value of P is 90 N. The value of a at which bending moment is minimum is to be…

Q: What are the STANDARD SI UNITS For Resultant force, FR Couple moment, M Load Intensity, w What are…

A: Let us discuss the units of given three quantities.

Q: What about the other force. I only see the cos and sin of force 1414.21 and 45 degrees.…

A:

Q: Draw shear force and bending moment diagrams

A:

Q: The beam shown in the figure is subjected to two forces. What would be the resultant moment about…

A:

Q: Select the correct statements regarding the equivalent force moment systems. (Select 3) If a…

A: An equivalent force moment system is a system that consists of a single force and moment at a point…

Q: 3) A point mass is attached to one end of a beam levered against a spike which acts as the pivot.…

A:

Q: 4 A Moving to another question will save this response. Question 19 Point O (0, 0) is the fixed…

A:

Q: A beam with a length of 8 meters is known to carry both distributed and point loads as well as one…

A:

Q: Consider the tripod in (Figure 1). Figure 25m Part A Determine the magnitude of the moment of the…

A: To find:Magnitude of the moment of the force about member AB of the tripod.Given:The force is given

Q: If Mg = 65.0 kN-m and Mc = 52.5 kN-m, use the graphical method to construct the bending-moment…

A: Given data: ◆ The concentrated couple applied at B and fixed support C: MB = 65 kN•m , MC = 52.5…

Q: Replace the force system acting on the beam by an equivalent resultant force and couple moment at…

A:

Q: change in the forces so D is 300N and B is 200N. Need help solving for Ay and Cy.

A: Draw the free-body diagram of the given system.

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.