The toleranced diameter of a hole is given as 0.990"/1.010" and the size of the mating pin is given as 8.985"/0.980" 37. What is the maximum clearance for this fit? a) 0.030" b) 0.020" c) 0.025" d) 0.010" 38. What type of fit is this? transition b. clearance interference none of the above C. 39. A fit can be determined by specifying: upper limit b. allowance max. clearance d. b& c all the above a. C. 40. A fit is specified as 60H11 9 in Metric unit. What is the tolerance grade for the shaft? a. 60 b. 9 11 C. d. none above

Q: For the Timing Waveform Diagrams shown below, which is the correct drawing for an AND gate? Answer…

A: AND is a logical operator, used to perform logical operations. when both the inputs are TRUE, then…

Q: I have three parts that I need answered pertaining to the print provided below.   Did the person…

A: Yes, the given print is created by using the cylinder rule. Hence, the option (a) is correct.

Q: Mechanical advantage is the ratio of effort to load. a) True b) False

A: Mechanical advantage is the ratio of effort to load. a) True b) False

Q: Tolerance Maximum Limit Minimum Limit 57/8" 7'9 1/16" 16.76" 5 13/32" 7'8 15/16" 0.03" 0.007" 0.904"…

A: It is required to complete given table

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: F = 4 kN F, =5 kN F, = 8 kN A) F2 = 8.cos45.i + 5.sin45.j B) F2 = 5.cos45.i + 5.sin45.j 2 C) F2 =…

A: GivenF1=4 kNF2=5 kNF3=8 kNExpress F2 force as a vector form

Q: . The stress, S, on a pipe varies jointly with the internal pressure, P, and the internal diameter,…

A: Given Data: The stress on the pipe P=100 lbin2 The internal pressure on the pipe σ=25 lbin2 Diameter…

Q: Spinning at 10.0 revolutions per second (rev/s). The diameter of the electric drill bit is 4.00 mm.…

A: Given:- N=10 rev/sec d=4mm To find- Linear speed

Q: d) D Roller Support Cable Support 20N 3N 50N

A:

Q: a.) F F F b.) 1 kip 0.5 kip 3 kips H 2 kips 2 kips 1.5 kip D K M

A:

Q: Redraw the shown feature control frame in an acceptable location that indicates the tolerance…

A: Consider the diagram shown below for the given figure with front view, Here t is the thickness of…

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance? C…

A: Given data as per the question Pin diameter =0.498

Q: 29) For the shaft and hole sizes shown in the figure, specify the type of f 5.000 4.997 11 Clearance…

A: This question is based on the concept of limit fit and tolerance.As per the guidelines we are…

Q: The crate in (Figure 1) has a center of gravity at G. Figure P 4.5 ft 2.5 ft 3.5 ft 1 of 1 Part A…

A:

Q: You want to upgrade the tires on your truck. The manufacturer tires are P160/70R14. You want to…

A:

Q: On attached drawing 11A017 ,What is the length of the dovetail slot?   All abbreviations are…

A: In the given drawing the length of the dovetail slot is in the side view. The dovetail slot is…

Q: I need help solving problem numbers 4--15.

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: Geometric Dimensioning & Tolerancing is a symbolic language for dimensioning and tolerancing a…

A: 1.Geometric Dimensioning & Tolerancing is a symbolic language for dimensioning and tolerancing a…

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.