Tolerance Maximum Limit Minimum Limit 57/8" 7'9 1/16" 16.76" 5 13/32" 7'8 15/16" 0.03" 0.007" 0.904" 1.7001" 1.6998" 0.004" 10.999"

Q: Pin: MMC LMC Geom. Tol. с 1.000 1 1.000 Ø.515-.540 Hole 0.010M ABC 1.000 B Figure for Problem 21…

A:

Q: What type of geometric tolerances have no datum features? Profile Tolerances All Tolerances O…

A: Geometrical Tolerancing: The tolerances in any system which allows tolerances to be applied…

Q: 3. During tug of war, the bicep muscle generated 4k N force that was perpendicular to the forearm…

A:

Q: The Boss is created at 59.88, what is the allowed Position Tolerance?

A: Given data as per question Basic size of the boss =60

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: In the following figure, add the tolerance zone and limits of size for both parts.

A:

Q: If the tolerance in the figure below is for a pin .525 in diameter, what is the total positional…

A:

Q: I need help with question number 15 that is pertaining to the print provided.

A: 15.The unidirectional system is used here for the dimension placing. The unidirectional system is…

Q: Apply the necessary symbology to establish the required tolerance and datum features to control the…

A:

Q: Use the prefix multipliers to express cach measurement without any exponents. 22 x 10-15s

A: Given: The time is t=22×10-15 s. The unit conversion factor to convert Second into Femtosecond is, 1…

Q: 13. What type of geometric tolerance has no datum features? 14. A theoretically exact dimension is…

A: As per Bartleby guidelines, this is a multipart question and we will answer the first three…

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance?…

A: Total positional tolerance shows us the maximum allowable deviation of a feature from its true…

Q: Complete an interpretation drawing that shows the required datum and the perpendicularity tolerance…

A: Perpendicularity: In GD&T the Perpendicularity is defined the two different…

Q: Using the Metric Full Scale Below, what is the red dimension below to the nearest Millimeter? .01…

A: Steps

Q: 8. If the limits of size for a hole are .384" and .394" diameter, and the position tolerance is…

A: Write the given data. Minimum limit=0.384"Maximum limit=0.394"Positional tolerance at MMC=0.009"

Q: Using the Engineering Scale 1" = 20', what is the red dimension below to the nearest foot? 20 20 0 1…

A:

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance? C…

A: Given data as per the question Pin diameter =0.498

Q: dimension the distance between the holes

A: Bilateral tolerance B = 1.625T = 0.006Bilateral tolerance means that the dimension can vary in both…

Q: All form tolerances are surface controls except for Form tolerances are independent of all other and

A: Form tolerance is a used to determine the form of the part. It refers to the limitation of a form…

Q: On attached drawing 11A017 ,What is the length of the dovetail slot?   All abbreviations are…

A: In the given drawing the length of the dovetail slot is in the side view. The dovetail slot is…

Q: I need help solving problem numbers 4--15.

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: Chapter 3: 13. What type of geometric tolerance has no datum features? 14. A theoretically exact…

A: subject : engineering drawing

Q: Using the diagram, determine the minimum clearance, in inches. DIA A 0.000 0 -0001 6" BASIC…

A:

Q: how do you write this in a feature control frame? "The cross-sectional shape of this feature must be…

A: The feature control frame is required to describe the condition and tolerances of the geometric…

Q: Which type of feature doesn't belong to orientation tolerances?         Concentricity…

A: using datum plane measure the Angularity , Perpendicularity and  Parallelism

Q: The term "Allowance" in limits and fits is usually referred to 1. Minimum clearance between shaft…

A: Allowance :- (A) Minimum clearance between the shaft and hole The minimum clearance in a shaft and…