8. If the limits of size for a hole are .384" and .394" diameter, and the position tolerance is specified as .009" diameter at MMC, the allowable position tolerance for a hole produced at 386" diameter is. A. .007 B. .009 C. 011 D. 015

8. If the limits of size for a hole are .384" and .394" diameter, and the position tolerance is specified as .009" diameter at MMC, the allowable position tolerance for a hole produced at 386" diameter is. A. .007 B. .009 C. 011 D. 015

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: For nominal diameters d = 40 mm and d = 80 mm, determine one interference fit according to the unit…

A: Given data as per the question d = 40 mm d = 80 mm,

Q: A metal disc of 20mm diameter is to be punched from a sheet of 2mm thickness. The punch and the…

A: Given operation is blanking operation. Blank operation = D = 20 mm Sheet thickness = t = 2mm…

Q: What type of geometric tolerances have no datum features? Profile Tolerances All Tolerances O…

A: Geometrical Tolerancing: The tolerances in any system which allows tolerances to be applied…

Q: Specify a cylindricity tolerance of .0004 for the largest cylindrical surface on the part in the…

Q: Compute the following: Basic size Tolerance Maximum limit size Minimum limit size

A: Machine drawing is the drawing in which component details are given in geometrical view. For…

Q: I have three parts that I need answered pertaining to the print provided below. Did the person…

A: Yes, the given print is created by using the cylinder rule. Hence, the option (a) is correct.

Q: Which position tolerance is shown in below’s technical drawing? Explain the meaning (that is the…

A: Which position tolerance is shown in below technical drawing?Explain the meaning (that is the…

Q: A solid steel shaft with a diameter of 130 mm must be press-fitted in a journal bearing (Figure 1)…

Q: A specifeid hole diameter of min and max has specified tolerance at LMC. A produced hole of diamter…

A: Introduction: Tolerances in mechanical engineering define the permissible variation from specified…

Q: - The dimensions for the shaft size are o10*00 0.009 mm and the hole size are b 10*0.015 +0.000 mm.…

A: Shaft sizeϕ10-.009+0.00Maximum limit of shaft =10+0.000=10.00 mmMinimum limit of shaft=…

Q: On the part shown, specify a paralellism tolerance to make the top surface parallel to datum A…

Q: Tolerance Maximum Limit Minimum Limit 57/8" 7'9 1/16" 16.76" 5 13/32" 7'8 15/16" 0.03" 0.007" 0.904"…

A: It is required to complete given table

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: What is the LMC of hole D?

A: LMC stands for Least Material Condition, which is the feature of the size of the object that…

Q: What is the philosophy of the Go and No-Gogauging? Complete any missing information on part 182 and…

A: PHILOSOPHY OF GO & NO GO GAUGING:- 1.GO end gauging :- Go end used in qualify the…

Q: If the tolerance in the figure below is for a pin .525 in diameter, what is the total positional…

Q: Match each of the following terms to the phrase that describes it. Answers are used only once.

A: The correct match is: Drill spot - 3Countersink - 6Knurl -…

Q: 2. Nominal size is 40mm, the clearance is between 24µm and 92µm, the span of the clearance fit is…

A: Note: Since you have posted a question with multiple sub-parts, we will solve first three sub- parts…

Q: ch Liner (ID 6.270

Q: 2. Draw the appropriate geometric tolerance symbols for the flatness and angularity.

Q: Use the prefix multipliers to express cach measurement without any exponents. 22 x 10-15s

A: Given: The time is t=22×10-15 s. The unit conversion factor to convert Second into Femtosecond is, 1…

Q: Design a fit for an industrial app

A: Given: Hole basic system Basic side=100 mm Maximum clearance= 0.093 mm Minimum clearance=0.036 mm To…

Q: Please write the definitions for tolerances, draw the hole shaft basis diagram. Write down different…

A: Definition of tolerances: Tolerancing is genuinely like made tongues. It has its own norms. In a…

Q: Find the tolerance and fit type of Ø 60 H7k6,

A: given: nominal size, D=60mm tolerance hub: H7 tolerance shaft: k6 so for tolerance hub: H7, the…

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance?…

A: Total positional tolerance shows us the maximum allowable deviation of a feature from its true…

Q: Outside calipers are used for measuring diameters of holes. Select one: True False

A: Outside calipers are used for measuring diameters of holes. Answer: False

Q: 5. If the pin in the figure below were produced at a diameter of 1.004 and toleran the feature…

A: Given Pin produced at diameter=∅1.004 And∅1.000-1.010

Q: -0.0025 1. The dimensions for the shaft size are o50-0.0037 mm and the hole size are +0.000 mm. Find…

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: Complete the needed calculations and enter the needed values in the given table. All problems are…

Q: What type of form tolerance is shown in this figure? Flatness Straightness Cylindricity…

A: Given data : Figure

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance? C…

A: Given data as per the question Pin diameter =0.498

Q: Consider the figure shown below, (enter all answers in this format 0.XXX) 4XØ 255 a 005 O 010 B -50…

A: TOTAL POSITION TOLERANCE The GD&T symbol for location tolerance is position tolerance. The True…

Q: Protracted and geometric angular tolerances are identical. True False

A: intro- protracted and geometrical angular tolerance both are identical.

Q: Apply a perpendicularity tolerance to control the pin within a 0.015" cylindrical tolerance zone at…

A: Given:

Q: Complete feature control frame that controls perpendicularity of the hole to .012" diameter at MMC…

Q: I need help solving problem numbers 4--15.

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: 50 +0.012 mm and the hole size are 1. The dimensions for the shaft size are +0.015 50+0.005 +0.000…

Q: Which method specifies the tolerance by providing dimensions for the upper and lower limit in place…

A: Definition of Tolerance : Tolerance is the total permissible variation of a size, means it is not…

Q: plete the hole specification including a position tolerance of C ary datum feature A, secondary…

A: Given-Information:- To-Determine:- Complete hole specification

Q: The term "Allowance" in limits and fits is usually referred to 1. Minimum clearance between shaft…

A: Allowance :- (A) Minimum clearance between the shaft and hole The minimum clearance in a shaft and…

Q: the various parts? 13. What is the tolerance on "F," the chamfer angle? 13 14. How square must the…

A: 13. 6 ° is the tolerance on "F" the chamfer angle As 20° - 14° = 6° 14. square must the ends of…

Q: What tolerance is specified for the width of the groove?

A: Given :- Bolt Drawing Find :- Tolerance of the width of the drawing

Q: ng information. Determine the ole size (minimum diameter) of the parts = 0.005"

A: The basic hole size is-Tolerance of the parts-Allowance-

Question

If the limits of size for a hole are .384 and .394 diameter with positon tolerance .009 at MMC, what is the allowable position tolerance produced at .386?

8. If the limits of size for a hole are .384" and .394" diameter, and the position tolerance is
specified as .009" diameter at MMC, the allowable position tolerance for a hole produced at
386" diameter is________"
A. .007
B. .009
C. .011
D.
.015

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

3. If there is a 0.10 mm accuracy error for all measured parameters at Instruction 1, determine the true volume of the allen bolt. Also, comment on the difference between volume calculated by measured data and volume calculated by true data.
Draw feature control frame (FCF) of the following characteristics: Profile of line tolerance zone .500 at LMC to datum A Angularity with tolerance zone 0.10 at MMC to datum A at LMC Position tolerance zone .012 in diameter at MMC to datum A, B and C.
To which of the following geometric tolerance families does perpendicularly belong? Form Tolerance. Location tolerance. Profile tolerance. Orientation tolerance
I need help matching the terms to the phrase it describes.
Correct answer writing
state the functions of interference fit and draw it on illustration of size tolerance zone .
2 5 What is the shape and size of this tolerance zone? 1.25 0.50 Diam +/-0.002" 0.010
Would a flatness tolerance of .010 for the part in the drawing below be appropriate? Yes O No 3.000 1.000 XXX = +.005 ANGLES ± 1°
What is the orientation geometric tolerance that is applied to this feature?: __________ Does the tolerance control a surface, axis, or center plane?: __________ What is the applied tolerance if the feature is produced at MMC?: __________
Fill in the table regarding the hole and shaft below. Assume ANSI tolerancing.
What type of geometric tolerances has no datum features? O Location O Runout O Profile O Form
Please answer as many as you can, no solution needed