Answered: Complete an interpretation drawing that…

Engineering

Mechanical Engineering

Complete an interpretation drawing that shows the required datum and the perpendicularity tolerance zone

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.87P: (a) Find the volume of liquid contained in the ï¬‚ask when it is filled to the full mark. (b)...

See similar textbooks

Related questions

Q: Which percentile is typically for designing lower-limit dimensions? - 95th 5th 50th 99th

Q: I have three parts that I need answered pertaining to the print provided below. Did the person…

A: Yes, the given print is created by using the cylinder rule. Hence, the option (a) is correct.

Q: How many basic dimensions are on the print shown in the figure provided?

A: Basic dimensions are theoretically exact dimensions that define the ideal size, location,…

Q: In the following figure, add the tolerance zone and limits of size for both parts.

Q: Suppose parts are to be fitted together as shown below. Dimensions and tolerances (in inches) are in…

A: Given: The dimension with tolerances are d=1.750±0.003, a=0.150±0.006, c=1.400±0.001. The dimension…

Q: ne 1/2-inch diameter pin in the drawing below is required to be perp ature A within tolerance of…

A: A feature control frame is used to show the conditions and tolerances of the dimension of the part…

Q: Use the graphical method to break F into components parallel to bars AB and BC. If the component…

A: According to the given data FAB =7kN a = 300mm b = 75mm c = 100mm we need to find Force in the…

Q: Find the tolerance and fit type of Ø 60 H7k6,

A: given: nominal size, D=60mm tolerance hub: H7 tolerance shaft: k6 so for tolerance hub: H7, the…

Q: a Show how Pip can complete the circuit by adding less than 120 cm of track. b Show how Pip can…

Q: Q1: Use scale (1:1), draw the front, top & side views of shape shown below. (50 M)

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A: Step 1:a. Equation for the differential area aligned horizontally The differential area element dA…

Q: What company specification number is given to the material for this part? 2. What is the revision…

A: Engg drawing is a technical drawing that is used to transfer the information from the design to the…

Q: A sphere and cylinder shown in (Eigure 1) are released from rest on the ramp at t = 0. Part A If…

A: For the solution refer below images.

Q: Refer to drawing 21A033, what is dimension G? (Please note that you can't just assume the hub…

A: Pulleys are used for transmission of power from the driver shaft to the driven shaft. The hub of the…

Q: a) Three blocks A, B, and C and a grooved block D have dimensions a, b, c, and d as follows:…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Q: Given the points A( – 5, 6, – 4), B( – 2, 10, 6), and C(4, 0, 5), find (a) the angle between AB →…

A: Given data: A-5,6,-4B-2,-10,6C4,0,5 Need to determine the angle between the position vectors.

Q: When no geometric tolerance is specified, the size tolerance controls the well as the size. O form O…

A: Size tolerance and geometric tolerance controls the tolerance of different specification aspects.…

Q: Fill in the two feature control frames below for rings 1 and 2. Use the virtual sizes from above,…

A: feature control volume consists of the tolerance value of the two mating parts . Various symbols…

Q: Need Help on both Questions.

A: The A is for datum The symbol is used for perpendicular. The distance between two parallel line…

Question

Complete an interpretation drawing that shows the required datum and the perpendicularity tolerance zone

Expert Solution

Step 1

Perpendicularity:

In GD&T the Perpendicularity is defined the two different things/surfaces/edges which are depending on which the reference feature is called out.

Now there are two different types of Perpendicularity as given below:

Surface Perpendicularity is a tolerance that controls Perpendicularity between two 90° surfaces.
Axis Perpendicularity is a tolerance that controls how perpendicular a specific axis needs to be to a reference datum

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

(a) Find the volume of liquid contained in the ï¬‚ask when it is filled to the full mark. (b) Determine the elevation h of the half full mark.
Determine the volume of the concrete arch dam.
Q.3) Find the Centroid of the composite area shown below. 50 mm | 25 mm 30 mm 25 mm 50 mm 50 mm
Q1.) The assembly shown here is comprised of a block and cylinder made of different materials. The block has a specific weight of 0.125 lb/in³ with a 2 x 2 square inch hole as shown. The specific weight of the cylinder is 0.08 lb/in³. Determine the combined weight of the assembly and locate the center of gravity with respect to the given axes. Assume the cylinder is centered on the front of the block. 6 in. 6 in. y 3 in. 5 in 2 in 0.5 in 0.5 in 2 in Top View 2 in X
Write the equation of the Centroid of an area?
An engine has four cylinders of 68 mm bore and 75 mm stroke. The cubic capacity of the engine is (a) 1089.5cm3 (b) 1289.5cm3 (c) 1489.5m3 (d) 1689.5cm3
As shown, a section of a roller coaster track (Figure 3) follows the form of y=(2/3)x1.5 . Locate the centroid x¯ of the track between x=0 m and x=4m . Express your answer numerically in meters to three significant figures.
A bronze bushing is mounted inside a steel sleeve. Knowing that the specific weight of bronze is 0.318 lb/in3 and of steel is 0.284 lb/in3 , determine the location of the center of gravity of the assembly.
Please help.
#7?
Please help. Written on paper not typed on computer or keyboard please. Need help on both questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.
Question 1 Locate the centroid of the shaded area. See figure Below. Note that is 24 cm. 30 ст 30cm X- 24cm A) (42.31, 46.06) B (25.19, 37.65) (24.13, 60.40) D (13.24, 40.06) E) (37.65, 25.19) F) (24.13, 40.06) G) (31.42, 40.60) H) (40.06, 24.13)