Refer to the figure below. What is the MMC, LMC and geometric tolerance for the Hole and Pin: a. Hole: MMC LMC Geom. Tol. b. Pin: MMC LMC Geom. Tol. C 1.000 1.000 Ø.515-.540 Hole 0.010MABC 1.000 B Ø.495-.500 Pin +0.005MABC A

Q: Pin: MMC LMC Geom. Tol. с 1.000 1 1.000 Ø.515-.540 Hole 0.010M ABC 1.000 B Figure for Problem 21…

A:

Q: 1. For the following part sizes and geometric tolerances, determine the appropriate geometric…

A: Givenϕ 2.062-0.0050.00⊥-Perppendular Toleranceϕ⊥=0.002

Q: What type of geometric tolerances have no datum features? Profile Tolerances All Tolerances O…

A: Geometrical Tolerancing: The tolerances in any system which allows tolerances to be applied…

Q: Specify a cylindricity tolerance of .0004 for the largest cylindrical surface on the part in the…

A:

Q: Apply geometric tolerancing to part according to the instructions below. This exercise will provide…

A: The majority of current production techniques and equipment are incapable of producing items that…

Q: The Boss is created at 59.88, what is the allowed Position Tolerance?

A: Given data as per question Basic size of the boss =60

Q: A rectangular block 100 mm x 150 mm has a hole with diameter 60 mm at the center. The hole tolerance…

A:

Q: A material condition used to indicate that a specified geometric tolerance applies at each increment…

A:

Q: ne 1/2-inch diameter pin in the drawing below is required to be perp ature A within tolerance of…

A: A feature control frame is used to show the conditions and tolerances of the dimension of the part…

Q: Given the following mechanical engineer's scale, deter- mine the readings at A, B, C, and D. C - 10…

A: Note:- As per the guidelines of Bartleby, only one answer is allowed to answer, so please submit…

Q: If the tolerance in the figure below is for a pin .525 in diameter, what is the total positional…

A:

Q: I need help with question number 15 that is pertaining to the print provided.

A: 15.The unidirectional system is used here for the dimension placing. The unidirectional system is…

Q: Use the prefix multipliers to express cach measurement without any exponents. 22 x 10-15s

A: Given: The time is t=22×10-15 s. The unit conversion factor to convert Second into Femtosecond is, 1…

Q: 1. For the following part sizes and geometric tolerances, determine the appropriate geometric…

A: (A) Pin, φ2.062-0.005+0.000  tolerance =upper limit - lower limit tolerance = 0.000-(-0.005)…

Q: 3. If the tolerance applies at MMC then a possible O indeterminant bonus O LMC zero tolerance…

A: given = fill in the blanks

Q: For the following part sizes and geometric tolerances, determine the appropriate geometric tolerance…

A: A.    Geometric tolerance = 0.005 + 0.007                                     = 0.007…

Q: 5. If the pin in the figure below were produced at a diameter of 1.004 and toleran the feature…

A: Given  Pin produced at diameter=∅1.004  And∅1.000-1.010

Q: 8. If the limits of size for a hole are .384" and .394" diameter, and the position tolerance is…

A: Write the given data. Minimum limit=0.384"Maximum limit=0.394"Positional tolerance at MMC=0.009"

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance? C…

A: Given data as per the question Pin diameter =0.498

Q: dimension the distance between the holes

A: Bilateral tolerance B = 1.625T = 0.006Bilateral tolerance means that the dimension can vary in both…

Q: Consider the figure shown below, (enter all answers in this format 0.XXX) 4XØ 255 a 005 O 010 B -50…

A: TOTAL POSITION TOLERANCE The GD&T symbol for location tolerance is position tolerance. The True…

Q: Complete feature control frame that controls perpendicularity of the hole to .012" diameter at MMC…

A:

Q: 2.012 2.010 Tol Virtual Feature ø.002 MA Size Zone Size Ø2.012 .002 Ø2.011 .003ØZ.014 02.010 Ø.004…

A:

Q: I need help solving problem numbers 4--15.

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: Chapter 3: 13. What type of geometric tolerance has no datum features? 14. A theoretically exact…

A: subject : engineering drawing

Q: Using the diagram, determine the minimum clearance, in inches. DIA A 0.000 0 -0001 6" BASIC…

A:

Q: Need solution to both questions.

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Limits, Fits, and Tolerances

The maximum or minimum allowable sizes within which the size of component lies are known as limits. The limits are classified into two types: