What is the Bolt size? (don't worry about the tolerances)

Q: . a. On the part shown, show a angularity specification to orient the angled surface in relation to…

A:

Q: What type of geometric tolerances have no datum features? Profile Tolerances All Tolerances O…

A: Geometrical Tolerancing: The tolerances in any system which allows tolerances to be applied…

Q: I have three parts that I need answered pertaining to the print provided below.   Did the person…

A: Yes, the given print is created by using the cylinder rule. Hence, the option (a) is correct.

Q: n an engine, the piston diameter is 3 1/4 inches, the stroke is 4 7/8 inches, and the piston…

A: For the solution refer below images.

Q: Apply geometric tolerancing to part according to the instructions below. This exercise will provide…

A: The majority of current production techniques and equipment are incapable of producing items that…

Q: I need help matching the parts of the print to the terms.

A: Tolerance block will go with choice E.

Q: Fixing a wheel barrow takes a specific diameter axel of 2.50 inches. Thankfully, the manufacture…

A: It is given that the axle required for fixing the wheel barrow should have a diameter of 2.50…

Q: In the following figure, add the largest equal coordinate tolerances so that if two parts are…

A: Maximum distance between mating hole centers, d = 0.5 mmLets assume the equal coordinate tolerance…

Q: The total positional tolerance equals the sum of the tolerance. O bonus and plus/minus O limit and…

A: According to the given data, we need to fill in the blank part.

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: I need help with question number 15 that is pertaining to the print provided.

A: 15.The unidirectional system is used here for the dimension placing. The unidirectional system is…

Q: 1st image : What is the reading on the micrometer? 2nd image : What is the reading on the…

A:

Q: Study the sheet metal assembly at the top of the image. It consists of two main parts, a flexible…

A: Given : To find : Datum features , tolerances

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance?…

A: Total positional tolerance shows us the maximum allowable deviation of a feature from its true…

Q: For the following thread designation, turns, how far have you advanced the O 083 inches O 417 inches…

A:

Q: The horsepower (hp) that a shaft can safely transmit varies jointly with its speed (in revolutions…

A:

Q: 8. If the limits of size for a hole are .384" and .394" diameter, and the position tolerance is…

A: Write the given data. Minimum limit=0.384"Maximum limit=0.394"Positional tolerance at MMC=0.009"

Q: I need help answering these 3 parts. 1. The size description of an object on the print can best be…

A: The size description of an object on the print can best be described as dimensioning.The correct…

Q: 1. 1. Which part has the longest length? 2. 2. Which part has the smallest tolerance for the outside…

A: As this question contains multiple parts, solution is provided for first three parts as per policy.…

Q: Apply a perpendicularity tolerance that results in a virtual condition of .379" diameter for the…

A: Given data as per the question Diameter of pin =0.375 unit Diameter of hole =0.382 unit

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance? C…

A: Given data as per the question Pin diameter =0.498

Q: There are several failure modes by which gears can fail. Select the true statement from among the…

A:

Q: 7-Either the following text: Standardization is an activity that consists of developing rules…

A: It is asked to generate stick scriptWhat is te role of orientation marker How the inscription…

Q: Sally is making a sine bar, which is used to machine angles on parts (see the given figure). She has…

A:

Q: Dimensions are the linear or angular sizes of a component specified on the part drawing: Group of…

A: Introduction: Engineering drawings are a subset of technical drawings. The goal is to provide all of…

Q: What is the MMC of hole "D"?

A: The maximum material condition (MMC) tells the amount of maximum material of the smallest diameter…

Q: Consider the figure shown below, (enter all answers in this format 0.XXX) 4XØ 255 a 005 O 010 B -50…

A: TOTAL POSITION TOLERANCE The GD&T symbol for location tolerance is position tolerance. The True…

Q: I am going to use a Bolt through the .41 DIA holes to align the parts, answer the following: What…

A:

Q: SPECIFY WHERE DIMENSIONS NEED TO BE PLACED FOR THE FOLLOWING PART NOTE: JUST NOTE WHERE…

A: To mark the letters on the following figure mentioned.

Q: Question 3 The figures (1&2) shows a Hole-Pattern as drawn and as inspected. fill table 1 and…

A:

Q: I need help solving problem numbers 4--15.

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Joining Processes

It is the process of permanent or temporary joining of two metal pieces with the help of heat or pressure. Two metal parts are assembled by applying an energy source for the formation of a single unit. The obtained joined metals cannot be fragmented easily with the application of any force.