Dimensions are the linear or angular sizes of a component specified on the part drawing: Group of answer choices true false

Q: Draw the following using the given figure: 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3.…

A: Find 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3. Isometric Drawing

Q: What is the distance between the center of circle A and the corner at B? R3 03 Start a new drawing…

A: According to the given data Horizontal distance between A and B =18 Vertical Distance between A and…

Q: Q3 A car A is travelling along a straight path, while a lorry B is travelling along a circular path…

A: solution; at X=3curvature of car B (RB)=200mspeed of car A (VA)=(150+X) km/h…

Q: The drag forces on objects of different size but similar shape have been measured in a moving fluid.…

A: GivenThe drag force can be calculated using the following formula:Where:D is the drag force.Cd is…

Q: The object shows the center of the whole is three inches from the left surface and one inch from the…

A: we have to determine what kind of dimensions are used in the hole

Q: Determine the range

A: Given data: The magnitude of vertical weight, W = 1200 N. Coefficient of static friction, µs = 0.30…

Q: 400 300 stn 60

A: 400sinθ=500sin60=5003/2=10001.732=578.03

Q: Another name for "SIZE DESCRIPTION is: 37 A Dimensioning B Orthographic projection. C Assembly…

A: Given Engineering drawing To find Size description Leader line Extension line

Q: Draw back the drawing given with the scale 1:1 on the new drawing paper using all the method on…

A: 1. Draw the horizontal reference line using Drafter to a some extent. 2. Draw the vertical…

Q: Draw back the drawing given  with the scale 1:1 on the new drawing paper using all the method on…

A: 1. First off all we need to locate the two points of the given part at distance of 200 mm apart in…

Q: Using the drawing below identify th mistake on dimensioning rules and write the correct method to…

A: According to DG&T standards, there are 5-dimensional mistakes that are highlighted in the fig…

Q: Problem 4: Constrained Modulus A mounting block made of butyl rubber of modulus = 0.0015 GPa is…

A:

Q: The quarter cylindrical gate AB has a radius of 1.5 m and length 3 m perpendicular to the paper. It…

A: Given:Radius of gate, R=1.5 mLength of the gate, L=3 mUnit weight of water, γ=9.80 kN/m3Find:The…

Q: Using the rules of projection find the true length of line AB using a 1:5 METRIC scale.

A: Given condition

Q: Ql: Draw the following views of given object: a. Left Half Section Front View b. Top View C- 80 28…

A: a) Left half section front view of given object can be drawn as

Q: What is the worst-case distance between the bottom surface of the slot and the botto surface of the…

A: Given drawing

Q: Problem 2: Values: FA = 20 N FB = 30 N a = 25° Use the graphical method to determine... a) the…

A:

Q: Question 3) On the  plate in the figure, the length  L  is given as L=72 m . According to this;…

A:

Q: ENTIRE ANSWER IS WRONG

A: Initial velocityFinal velocityInitial angleFinal angleWeight of the basketball

Q: 8 inch radius 8 inch circumference 8 inch all around 8 inch diameter R.70 4x 1.40 B IP 1.00 SECTION…

A: Select the correct statement about the notation circled in green and marked as letter.C. Assume all…

Q: Q1: Use scale (1:1), draw the front, top & side views of shape shown below. (50 M)

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Example 3.6 The gate in figure below is 5 ft wide, is hinged at point B, and rests against a smooth…

A:

Q: R.70 B 4x 1.40 There are 4 arched edges with radius 0.70 inches There are 4 arched edges with…

A:

Q: 9. During a static test of an airplane wing, the strain-gauge readings from a 45° rosette (see…

A: Given data : Gauge A reading () = 530*10-6 Gauge B reading () = 420*10-6 Gauge C reading () =…

Q: The Hardness It can be shown that the surface area of the impression is: D2-d2 2

A:

Q: The below figure shows two views of a bolster block. Draw, using 1 st angle projection and a…

A: (a) the given front elevation;

Q: I. GENERAL INSTRUCTIONS : Show complete formulas, solutions, and figures. Round off to 3 decimal…

A:

Q: List one requirement from each of the following that you may need to consider when completing…

A: Australian standards provide requirements and design practises to guarantee that goods and…

Q: Q1) Create an orthographic projection of the following object. Draw the three standard views-

A:

Q: When no geometric tolerance is specified, the size tolerance controls the well as the size. O form O…

A: Size tolerance and geometric tolerance controls the tolerance of different specification aspects.…

Q: I need these three parts answered (Multiple Choice). If you can not answer all three parts please…

A: Critical dimensions:Many companies want to emphasize the importance of a certain dimension in order…

Q: Question 16 Here is a way we can estimate the distance from the earth to the moon. When the moon is…

A: GIVEN DATA- Arc Length AB=6152 miles The radius of earth R=3960 miles We have to find both point…

Q: 5. Given the following sentence descriptions of the geometric tolerance information, correctly…

A: d. The planer surface must be perpendicular with in five thousandths of an inch tolerance zone…

Q: A point on a thin plate is subjected to the two successive states of stress shown. Determine the…

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.