Fundamentals of Heat and Mass Transfer
7th Edition
ISBN: 9780470917855
Author: Bergman, Theodore L./
Publisher: John Wiley & Sons Inc
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 4, Problem 4S.2P
A hot pipe is embedded eccentrically as shown in a material of thermal conductivity
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A very thin electrical strip providing heat flux of 909 W/m2 is attached to the plate as shown in the figure. The system is under steady state conditions where the bottom side of the system is perfectly insulated and the top side is exposed to convection and radiation (emissivity and temperature values are shown in the figure). If the top surface temperature of the plate is 348 K calculate the convective heat transfer coefficient in W/m2K.
Round your answer to the nearest integer value and write only the numerical value in the provided box, not the units.
calculate the heat transfer rate per unit length of a cylindrical wall of inner and outer radius as 0.1 m and 0.2 m and thermal conductivity value of 0.1 W/mK. the temperatures of inner and outer surfaces are 100 °C and 50°C respectively.
A cylindrical shape body of length is 1.9 m and diameter is 400 mm is inside a room where the ambient temperature is equal to 300 K. The initial temperature of the body is equal to 350 K. If the heat convective coefficient is equal to 1.3 W/m^2.K. What is the thermal conductivity K.
Chapter 4 Solutions
Fundamentals of Heat and Mass Transfer
Ch. 4 - In the method of separation of variables (Section...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - Consider the two-dimensional rectangular plate of...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - Using the thermal resistance relations developed...Ch. 4 - Free convection heat transfer is sometimes...Ch. 4 - Consider Problem 4.5 for the case where the plate...Ch. 4 - Prob. 4.9PCh. 4 - Based on the dimensionless conduction heat rates...
Ch. 4 - Determine the heat transfer rate between two...Ch. 4 - A two-dimensional object is subjected to...Ch. 4 - An electrical heater 100 mm long and 5 mm in...Ch. 4 - Two parallel pipelines spaced 0.5 m apart are...Ch. 4 - A small water droplet of diameter D=100m and...Ch. 4 - A tube of diameter 50 mm having a surface...Ch. 4 - Pressurized steam at 450K flows through a long,...Ch. 4 - The temperature distribution in laser-irradiated...Ch. 4 - Hot water at 85°C flows through a thin-walled...Ch. 4 - A furnace of cubical shape, with external...Ch. 4 - Laser beams are used to thermally process...Ch. 4 - A double-glazed window consists of two sheets of...Ch. 4 - A pipeline, used for the transport of crude oil,...Ch. 4 - A long power transmission cable is buried at a...Ch. 4 - A small device is used to measure the surface...Ch. 4 - A cubical glass melting furnace has exterior...Ch. 4 - An aluminum heat sink (k=240W/mK), used to cool an...Ch. 4 - Hot water is transported from a cogeneration power...Ch. 4 - A long constantan wire of 1-mm diameter is butt...Ch. 4 - A hole of diameter D=0.25m is drilled through the...Ch. 4 - In Chapter 3 we that, whenever fins are attached...Ch. 4 - An igloo is built in the shape of a hemisphere,...Ch. 4 - Prob. 4.34PCh. 4 - An electronic device, in the form of a disk 20 mm...Ch. 4 - The elemental unit of an air heater consists of a...Ch. 4 - Prob. 4.37PCh. 4 - Prob. 4.38PCh. 4 - Prob. 4.39PCh. 4 - Prob. 4.40PCh. 4 - One of the strengths of numerical methods is their...Ch. 4 - Determine expressionsfor...Ch. 4 - Consider heat transfer in a one-dimensional...Ch. 4 - In a two-dimensional cylindrical configuration,...Ch. 4 - Upper and lower surfaces of a bus bar are...Ch. 4 - Derive the nodal finite-difference equations for...Ch. 4 - Consider the nodal point 0 located on the boundary...Ch. 4 - Prob. 4.48PCh. 4 - Prob. 4.49PCh. 4 - Consider the network for a two-dimensional system...Ch. 4 - An ancient myth describes how a wooden ship was...Ch. 4 - Consider the square channel shown in the sketch...Ch. 4 - A long conducting rod of rectangular cross section...Ch. 4 - A flue passing hot exhaust gases has a square...Ch. 4 - Steady-state temperatures (K) at three nodal...Ch. 4 - Functionally graded materials are intentionally...Ch. 4 - Steady-state temperatures at selected nodal points...Ch. 4 - Consider an aluminum heat sink (k=240W/mK), such...Ch. 4 - Conduction within relatively complex geometries...Ch. 4 - Prob. 4.60PCh. 4 - The steady-state temperatures (°C) associated with...Ch. 4 - A steady-state, finite-difference analysis has...Ch. 4 - Prob. 4.63PCh. 4 - Prob. 4.64PCh. 4 - Consider a two-dimensional. straight triangular...Ch. 4 - A common arrangement for heating a large surface...Ch. 4 - A long, solid cylinder of diameter D=25mm is...Ch. 4 - Consider Problem 4.69. An engineer desires to...Ch. 4 - Prob. 4.71PCh. 4 - Prob. 4.72PCh. 4 - Prob. 4.73PCh. 4 - Refer to the two-dimensional rectangular plate of...Ch. 4 - The shape factor for conduction through the edge...Ch. 4 - Prob. 4.77PCh. 4 - A simplified representation for cooling in very...Ch. 4 - Prob. 4.84PCh. 4 - A long trapezoidal bar is subjected to uniform...Ch. 4 - Consider the system of Problem 4.54. The interior...Ch. 4 - A long furnace. constructed from refractory brick...Ch. 4 - A hot pipe is embedded eccentrically as shown in a...Ch. 4 - A hot liquid flows along a V-groove in a solid...Ch. 4 - Prob. 4S.5PCh. 4 - Hollow prismatic bars fabricated from plain carbon...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.arrow_forward1.1 On a cold winter day, the outer surface of a 0.2-m-thick concrete wall of a warehouse is exposed to temperature of –5°C, while the inner surface is kept at 20°C. The thermal conductivity of the concrete is 1.2 W/m K. Determine the heat loss through the wall, which is 10-m long and 3-m high. Problem 1.1arrow_forward*** **answer is correct To increase the rate of heat transfer from a device, which has 0.1 m² of exposed surface, you added 500 pin fins of 4 cm length and 2 mm diameter on top of the device's exposed surface. How much (i.e., by what factor) did the rate of total heat transfer rate (from the surface) increase? Assume that the convection coefficient is 42 W/m².K, and the thermal conductivity of the fin material is 240 W/m.K. Neglect radiation. 2:06arrow_forward
- yo lo:ll O %AV L. مرتضی نشط الآن Q5: The piston cylinder device (radius=10 cm) contains a liquid with a pressure 100 kpa and temperature of 20 ° C and has a liquid convection heat coefficient =93 WmK. Connect its fixed side to a cubic piece of aluminum (side length 15 cm) with a thermal conductivity coefficient of aluminum = 239 W mK. At the bottom of the aluminum piece there is a heat source with a temperature of 150 ° C, noting that the heat source is located in a vacuum chamber. Radiation thermal resistance = 3.17 K/W. Calculate the change in piston height during I sec. if you know that there is no change in the internal energy of the piston cylinder device. Note IK Watt 1KJ/s : Aaarrow_forwardElectrical current flows through a cylindrical cable with a diameter of d = 4 mm generating thermal energy at a uniform rate of 1.6x107 W/m3. There is an insulation of t = 3 mm thickness with a conductivity of 0.2 W/mK. The system is exposed to convection as shown in the figure. Be careful, the outer diameter of the system with insulation becomes d + 2t. Calculate the surface temperature, Ts of the cable in °C. Round your answer to the nearest integer value and write only the numerical value in the provided box, not the units.arrow_forwardSolve correctlyarrow_forward
- Calculate the quantity of heat conducted per minute through a duralumin circular disc 127 mm diameter and 19 mm thick when the temperature drop across the thickness of the plate is 5 degrees Celsius. Take the coefficient of thermal conductivity of duralumin as 150 W/(m-K).arrow_forwardA long solid rod of 20 mm diameter was inserted into a furnace while the other end was projecting into atmosphere at 28°C. The temperature at two points 100 mm apart were measured and found to be 125°C and 91°C respectively. Estimate the thermal conductivity of the rod, if heat transfer coefficient is 17.45 W/m?K.arrow_forwardConsider a long bar of square cross section (0.8 m to the side) and of thermal conductivity 2 W/m-K. Three of these sides are maintained at a uniform temperature of 320°C. The fourth side is exposed to a fluid at 100°C for which the convection heat transfer coefficient is 10 W/m2.K. Using an appropriate numerical technique with a grid spacing of 0.2 m, determine the midpoint temperature of the bar, in °C, and heat transfer rate between the bar and the fluid per unit length of the bar, in W/m. Tmid= a'come ! °C ! W/marrow_forward
- A thermometric well is placed in a pipe having diameter of 55 mm. Pipe wall temperature is 100°C and heat transfer coefficient inside the pipe is 300 W/m² K. Thickness of thermowell is 1.2 mm and its length is 50 mm. Thermal conductivity of thermowell material. Is 30 W/mK. If the temperature of the gas flowing through the pipe is recorded by thermometer as 200°C, determine the true temperature of gas. If the error in gas temperature is to be reduced by 80% by increasing the length of thermowell, determine the new length of thermowell. Draw a sketch of this thermowell. Take perimeter to area ratio for thermowell as 1/T (T= thickness).arrow_forwardGiven: Plate thickness: 30 mm k = 45 W/m°C Uniform volumetric heat generation: q = 25 MW/m³ Temperature on the right surface: 450K Temperature on the left surface: 390K Determine the following: (i) The equation for t(x). (ii) The maximum temperature and its location. (iii) The heat flow from each surface of the plate.arrow_forwardWater flows at 67 C inside a 2.5 cm inside diameter tube such that hi = 3500 W/m² .C . The tube has a wall thickness 0.72 mm with a thermal conductivity of 18 W/m.C. The outside of the tube loses heat by free convection with ho= 7.6 W/m².C. Calculate the overall heat transfer coefficient and heat loss per unit length to surrounding air at 15 C.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license