Fundamentals of Heat and Mass Transfer
7th Edition
ISBN: 9780470917855
Author: Bergman, Theodore L./
Publisher: John Wiley & Sons Inc
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 4, Problem 4.73P
To determine
Heat transfer rate per unit length of the bar between the bar and the fluid and temperature distribution in the bar.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A uniform internal energy generation occurs in a plane wall with a thickness of 60 mm and a constant thermal conductivity of 3W / m. K. For these conditions, the temperature distribution has the form T (x) = a + bx + c x?. The surface at x = 0 has a temperature = T = 110 ° C and experiences convection with a fluid for which To = 25 ° C and h = 300 W / m². K. The surface at x = L is well insulated. For one - dimensional, steady - state conduction (a) calculate the volumetric energy generation rate. (b) determine the coefficients a, b, and c by applying the boundary conditions to the prescribed temperature distribution.
I need answer within 20 minutes please please with my best wishes
Q2. Steam pumped through a long-
insulated pipe at a temperature of
T= 500 K and provides a convection
coefficient of h, = 100 W/m?K at the inner
surface of the pipe. The inner and outer
radius of the pipe and insulation material
are r1 = 10, r2 = 12 and r3 = 17 cm,
respectively. The thermal conductivity of
the pipe is 100 W/mK. The insulation
material is glass fiber and its outer surface
is exposed to ambient air at 300 K. If the ambient air provides a convection coefficient of ho = 20
Internal flow
Ambient air
W/m?K, determine the followings:
a. What are the thermal resistance coefficients for convections and conductions
b. What is the heat transfer rate per unit length of the pipe
c. If the pipe is 30 m long, what will be total heat transfer rate from the pipe.
t00 noints)
Chapter 4 Solutions
Fundamentals of Heat and Mass Transfer
Ch. 4 - In the method of separation of variables (Section...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - Consider the two-dimensional rectangular plate of...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - Using the thermal resistance relations developed...Ch. 4 - Free convection heat transfer is sometimes...Ch. 4 - Consider Problem 4.5 for the case where the plate...Ch. 4 - Prob. 4.9PCh. 4 - Based on the dimensionless conduction heat rates...
Ch. 4 - Determine the heat transfer rate between two...Ch. 4 - A two-dimensional object is subjected to...Ch. 4 - An electrical heater 100 mm long and 5 mm in...Ch. 4 - Two parallel pipelines spaced 0.5 m apart are...Ch. 4 - A small water droplet of diameter D=100m and...Ch. 4 - A tube of diameter 50 mm having a surface...Ch. 4 - Pressurized steam at 450K flows through a long,...Ch. 4 - The temperature distribution in laser-irradiated...Ch. 4 - Hot water at 85°C flows through a thin-walled...Ch. 4 - A furnace of cubical shape, with external...Ch. 4 - Laser beams are used to thermally process...Ch. 4 - A double-glazed window consists of two sheets of...Ch. 4 - A pipeline, used for the transport of crude oil,...Ch. 4 - A long power transmission cable is buried at a...Ch. 4 - A small device is used to measure the surface...Ch. 4 - A cubical glass melting furnace has exterior...Ch. 4 - An aluminum heat sink (k=240W/mK), used to cool an...Ch. 4 - Hot water is transported from a cogeneration power...Ch. 4 - A long constantan wire of 1-mm diameter is butt...Ch. 4 - A hole of diameter D=0.25m is drilled through the...Ch. 4 - In Chapter 3 we that, whenever fins are attached...Ch. 4 - An igloo is built in the shape of a hemisphere,...Ch. 4 - Prob. 4.34PCh. 4 - An electronic device, in the form of a disk 20 mm...Ch. 4 - The elemental unit of an air heater consists of a...Ch. 4 - Prob. 4.37PCh. 4 - Prob. 4.38PCh. 4 - Prob. 4.39PCh. 4 - Prob. 4.40PCh. 4 - One of the strengths of numerical methods is their...Ch. 4 - Determine expressionsfor...Ch. 4 - Consider heat transfer in a one-dimensional...Ch. 4 - In a two-dimensional cylindrical configuration,...Ch. 4 - Upper and lower surfaces of a bus bar are...Ch. 4 - Derive the nodal finite-difference equations for...Ch. 4 - Consider the nodal point 0 located on the boundary...Ch. 4 - Prob. 4.48PCh. 4 - Prob. 4.49PCh. 4 - Consider the network for a two-dimensional system...Ch. 4 - An ancient myth describes how a wooden ship was...Ch. 4 - Consider the square channel shown in the sketch...Ch. 4 - A long conducting rod of rectangular cross section...Ch. 4 - A flue passing hot exhaust gases has a square...Ch. 4 - Steady-state temperatures (K) at three nodal...Ch. 4 - Functionally graded materials are intentionally...Ch. 4 - Steady-state temperatures at selected nodal points...Ch. 4 - Consider an aluminum heat sink (k=240W/mK), such...Ch. 4 - Conduction within relatively complex geometries...Ch. 4 - Prob. 4.60PCh. 4 - The steady-state temperatures (°C) associated with...Ch. 4 - A steady-state, finite-difference analysis has...Ch. 4 - Prob. 4.63PCh. 4 - Prob. 4.64PCh. 4 - Consider a two-dimensional. straight triangular...Ch. 4 - A common arrangement for heating a large surface...Ch. 4 - A long, solid cylinder of diameter D=25mm is...Ch. 4 - Consider Problem 4.69. An engineer desires to...Ch. 4 - Prob. 4.71PCh. 4 - Prob. 4.72PCh. 4 - Prob. 4.73PCh. 4 - Refer to the two-dimensional rectangular plate of...Ch. 4 - The shape factor for conduction through the edge...Ch. 4 - Prob. 4.77PCh. 4 - A simplified representation for cooling in very...Ch. 4 - Prob. 4.84PCh. 4 - A long trapezoidal bar is subjected to uniform...Ch. 4 - Consider the system of Problem 4.54. The interior...Ch. 4 - A long furnace. constructed from refractory brick...Ch. 4 - A hot pipe is embedded eccentrically as shown in a...Ch. 4 - A hot liquid flows along a V-groove in a solid...Ch. 4 - Prob. 4S.5PCh. 4 - Hollow prismatic bars fabricated from plain carbon...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- = Consider a large plane wall of thickness L=0.3 m, thermal conductivity k = 2.5 W/m.K, and surface area A = 12 m². The left side of the wall at x=0 is subjected to a net heat flux of ɖo = 700 W/m² while the temperature at that surface is measured to be T₁ = 80°C. Assuming constant thermal conductivity and no heat generation in the wall, (a) express the differential equation and the boundary equations for steady one- dimensional heat conduction through the wall, (b) obtain a relation for the variation of the temperature in the wall by solving the differential equation, and (c) evaluate the temperature of the right surface of the wall at x=L. Ti до L Xarrow_forwardplease provide answers with step-by-step calculations and explanationarrow_forwardExample : A steel tube having k =46 W/m °C has an inside diameter of 3.0 cm and a tube wall thickness of 2 mm. A fluid flows on the inside of the tube producing a convection coefficient of 1500 W/m2 ° C on the inside surface, while a second fluid flows across the outside of the tube producing a convection coefficient of 197 W/m °C on the outside tube surface. The inside fluid temperature is 223 °C while the outside fluid temperature is 57 °C. Calculate the heat lost by the tube per meter of length.arrow_forward
- ANSWER THE QUESTION STEP BY STEP WITH FULL SOLUTION. NO CALCULATOR SHORTCUTS PLEASE.arrow_forward2. A steel plate of k=50W/mK and thickness 10cm passes a heat flux by conduction of 25kW/m2. If the temperature of hot surface of plate is 100 C, then what is the temperature of the cooler side of plate? 1. 30 C 2. 40 C 3. 50 C 4. 60 Carrow_forwardShown in the figure below is an insulated copper block that receives energy at a rate of 200 W from an embedded resistor. The temperature of the resistor is 34°C above the temperature of the copper block. Insulation Δt = Resistor 5000000000000000000000 oooooooooooooo....... Copper block If the block has a volume of 10-3 m³ and an initial temperature of 20°C, how long would it take, in minutes, for the temperature to reach 88°C? -V=10-³ m³ T₁ = 20°C minarrow_forward
- A long rod with a thermal conductivity of 1 W / m · K is subjected to the boundary conditions given in the figure. Find the temperature distribution in the steady state with the energy balance method for ∆x = ∆y = 0.2m. Also calculate the heat transfer between rod and fluid per unit length.arrow_forwardA section of a composite wall with the dimensions shown below has uniformtemperatures of 200°C and 50°C over the left and right surfaces, respectively. If the thermal conductivities of the wall materials are: kA = 70 W/(m K), kB = 60 W/(m K), kc = 40 W/(m K) and kD = 20 W/(m K), determine the rate of heat transfer through this section of the wall and the temperatures at the interfaces.arrow_forwardYou are asked to estimate the maximum human body temperature if the metabolic heat produced in your body could escape only by tissue conduction and later on the surface by convection. Simplify the human body as a cylinder of L=1.8 m in height and ro= 0.15 m in radius. Further, simplify the heat transfer process inside the human body as a 1-D situation when the temperature only depends on the radial coordinater from the centerline. The governing dT +q""=0 dr equation is written as 1 d k- r dr r = 0, dT dr =0 dT r=ro -k -=h(T-T) dr (k-0.5 W/m°C), ro is the radius of the cylinder (0.15 m), h is the convection coefficient at the skin surface (15 W/m² °C), Tair is the air temperature (30°C). q" is the average volumetric heat generation rate in the body (W/m³) and is defined as heat generated per unit volume per second. The 1-D (radial) temperature distribution can be derived as: T(r) = q"¹'r² qr qr. + 4k 2h + 4k +T , where k is thermal conductivity of tissue air (A) q" can be calculated…arrow_forward
- If the rate of heat flow through a furnace wall is 0.94 kW/m². The wall consisting of 0.20 m thick inner layer of chrome brick, a center layer of kaolin brick of 10.0 cm and an outer layer of masonry brick 100 mm thick, having a thermal conductivity of 1.25 W/m°C , 0.74x10ª kW/m°C_and 0.555x10³ kW/m°C respectively. The unit surface conductance at the inner surface is 74 W/m2 °C and the outer surface temperature is 70 °C . The temperature of the gases inside the furnace is 1670 °C , assume steady heat flow, Calculate the following: 1- The temperatures of the gases inside the furnace. 2- The interior surface temperature of the inner and outer layers.arrow_forwardThe nodal diagram shown is of a section of a flat plate with thermal conductivity of 51 W/m K. The left side and top side are exposed to the same convection environment at 35°C and 46.3 W/m² K. The divisions used have Ax = Ay = 11 cm. At steady state, the temperature at 1 is T₁ = 51.1°C, at 3 is T3 = 85.0°C, at 5 is T5 = 114.3°C, at 7 is T7 = 121.4°C, and 8 is Tg = 130.4°C. What is the temperature at 4, T4? Express your answer in °C. Too h 8 3 7 Ax = Ay Too h S 8arrow_forwardA plane wall of thickness 2L = 2*33 mm and thermal conductivity k = 7 W/m-K experiences uniform volumetric heat generation at a rate q˙, while convection heat transfer occurs at both of its surfaces (x = −L, + L), each of which is exposed to a fluid of temperature T∞ = 31°C. Under steady-state conditions, the temperature distribution in the wall is of the form T(x) = a + bx + cx2 where a = 85°C, b = −-218°C/m, c = −-23,942°C/m2, and x is in meters. The origin of the x-coordinate is at the midplane of the wall. (a) Sketch the temperature distribution and identify significant physical features. (b) What is the volumetric rate of heat generation q˙ in the wall? (c) Obtain an expression for the heat flux distribution qx″(x). Is the heat flux zero at any location? Explain any significant features of the distribution. (d) Determine the surface heat fluxes, qx″(−L) and qx″(+L). How are these fluxes related to the heat generation rate? (e) What are the convection coefficients…arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license