Introduction to Heat Transfer
6th Edition
ISBN: 9780470501962
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 4, Problem 4.81P
Spheres A and B arc initially at 800 K, and they are simultaneously quenched in large constant temperature baths, each having a temperature of 320 K. The following parameters are associated with each of the spheres and their cooling processes.
(a) Show in a qualitative manner, on
(b) Calculate the time required for the surface of each sphere to reach 415 K.
(c) Determine the energy that has been gained by each of the baths during the process of the spheres cooling to 415 K.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The nuclear fuel in cylindrical shape of length L at radius R is covered with aluminum shell at
radius RC. The heat energy (Sn) that emerges as a result of splitting in nuclear fuel is per unit volume
and is in the form of a parabolic function. Determine the temperature distribution in both regions
for the steady state by taking the outer surface temperature of the cylinder.
1/2
Sn = Sn. [a + b(r)]
"d
5.
RC
(cal/cm³ s)
To
Don’t use Heissler charts to answer this question
Heat sterilization of lumber, timbers, and pallets is used to kill insects to prevent their transfer between countries in international trade. This is analogous to food sterilization by heat. A typical requirement here is that the slowest heating point of any woodconfiguration be held at 56 °C for 30 minutes. Consider hot air heating of wooden boards that maintains their surface temperature at 70 °C. The boards are stacked outside and in the winter time they can be considered to be at 0 °Cwhen theyare brought in for heating. The thermal diffusivity of the wood is 9*10-8m2/s.
a.Calculate the time from the start of heating for a 2.5 cm thick board to reach a sterilization temperature of 56 °C at its slowest heating point
.b.Calculate the heating time when four such boards are stacked together.
c.Calculate the ratio of the two heating times (for a single board versus when they are stacked), and explain the ratio.
Note: You’re free to…
Hi, kindly solve this problem and show the solution. Thank you
Chapter 4 Solutions
Introduction to Heat Transfer
Ch. 4 - In the method of separation of variables (Section...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - Consider the two-dimensional rectangular plate...Ch. 4 - A two-dimensional rectangular plate is subjected...Ch. 4 - Prob. 4.5PCh. 4 - Prob. 4.6PCh. 4 - Free convection heat transfer is sometimes...Ch. 4 - Prob. 4.8PCh. 4 - Radioactive wastes are temporarily stored in a...Ch. 4 - Based on the dimensionless conduction heat rates...
Ch. 4 - Prob. 4.11PCh. 4 - A two-dimensional object is subjected to...Ch. 4 - Prob. 4.13PCh. 4 - Two parallel pipelines spaced 0.5 m apart are...Ch. 4 - A small water droplet of diameter D=100m and...Ch. 4 - Prob. 4.16PCh. 4 - Pressurized steam at 450 K flows through a long,...Ch. 4 - Prob. 4.19PCh. 4 - A furnace of cubical shape, with external...Ch. 4 - Prob. 4.21PCh. 4 - Prob. 4.22PCh. 4 - A pipeline, used for the transport of crude oil,...Ch. 4 - A long power transmission cable is buried at a...Ch. 4 - Prob. 4.25PCh. 4 - A cubical glass melting furnace has exterior...Ch. 4 - Prob. 4.27PCh. 4 - An aluminum heat sink k=240W/mK, used to coolan...Ch. 4 - Hot water is transported from a cogeneration power...Ch. 4 - Prob. 4.30PCh. 4 - Prob. 4.31PCh. 4 - Prob. 4.32PCh. 4 - An igloo is built in the shape of a hemisphere,...Ch. 4 - Consider the thin integrated circuit (chip) of...Ch. 4 - Prob. 4.35PCh. 4 - The elemental unit of an air heater consists of a...Ch. 4 - Prob. 4.37PCh. 4 - Prob. 4.38PCh. 4 - Prob. 4.39PCh. 4 - Prob. 4.40PCh. 4 - Prob. 4.41PCh. 4 - Determine expressions for...Ch. 4 - Prob. 4.43PCh. 4 - Prob. 4.44PCh. 4 - Prob. 4.45PCh. 4 - Derive the nodal finite-difference equations for...Ch. 4 - Prob. 4.47PCh. 4 - Prob. 4.48PCh. 4 - Consider a one-dimensional fin of uniform...Ch. 4 - Prob. 4.50PCh. 4 - Prob. 4.52PCh. 4 - Prob. 4.53PCh. 4 - Prob. 4.54PCh. 4 - Prob. 4.55PCh. 4 - Prob. 4.56PCh. 4 - Steady-state temperatures at selected nodal points...Ch. 4 - Prob. 4.58PCh. 4 - Prob. 4.60PCh. 4 - The steady-state temperatures C associated with...Ch. 4 - A steady-state, finite-difference analysis has...Ch. 4 - Prob. 4.64PCh. 4 - Consider a long bar of square cross section (0.8 m...Ch. 4 - Prob. 4.66PCh. 4 - Prob. 4.67PCh. 4 - Prob. 4.68PCh. 4 - Prob. 4.69PCh. 4 - Consider Problem 4.69. An engineer desires to...Ch. 4 - Consider using the experimental methodology of...Ch. 4 - Prob. 4.72PCh. 4 - Prob. 4.73PCh. 4 - Prob. 4.74PCh. 4 - Prob. 4.75PCh. 4 - Prob. 4.76PCh. 4 - Prob. 4.77PCh. 4 - Prob. 4.78PCh. 4 - Prob. 4.79PCh. 4 - Prob. 4.80PCh. 4 - Spheres A and B arc initially at 800 K, and they...Ch. 4 - Spheres of 40-mm diameter heated to a uniform...Ch. 4 - To determine which parts of a spiders brain are...Ch. 4 - Prob. 4.84P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Recent studies show that the major energy consumption in Fijian villages is wood which is used for cooking on open fires. Typical consumption of wood is 1 kg/person/day. (a) Estimate the heat energy required to boil a 2 litre pot full of water. Assuming this to be the cooking requirement of each person, compare this with the heat content of the wood, and thus estimate the thermal efficiency of the open fire. (b) How much timber has to be felled each year to cook for a village of 200 people ? Assuming systematic replanting, what area of crop must the village therefore set aside for fuel use if it is not to make a net deforestation ?arrow_forwardAn underwater sonar that maps the ocean bathymetry is encapsulated in a sphere with a diameter of 85 mm. During operation, the sonar generates heat at a rate of 300W. What is the sonar surface temperature when it’s located in a water column where the temperature is 15o C and the water current is 1 m/sec? The sonar was pulled out of the water without turning it off, thus, it was still working. The air temperature was 15o C and the air speed was 3 m/sec. What was the sonar surface temperature? Was there any reason for concern?arrow_forwardVacuum furnaces are used in manufacturing for metal heating in brazing and sintering processes, as well as for heat treatment of steel alloys. The vacuum, and absence of air/oxygen, facilitates a low contamination process and prevents detrimental surface oxidisation. Heat is often provided in these furnaces by electrical heating elements, and their thermal design is critical to the effective operation of the furnace. In one such case, this element is modelled as a long, cylindrical electrically heated rod, 20 mm in diameter installed in a vacuum furnace as shown. The surface of the heating rod has an emissivity of 0.9 and is maintained at 1000 K, while the interior walls of the furnace are black and are at 800 K. Calculate the net rate at which heat is lost from the rod per unit length.arrow_forward
- A brass plate has a circular hole whose diameter is slightly smaller than the diameter of an aluminum ball. Ifthe ball and the plate are always kept at the same temperature,(a) should the temperature of the system be increased or decreasedin order for the ball to fit through the hole? (b) Choose the bestexplanation from among the following:I. The aluminum ball changes its diameter more with temperature than the brass plate, and therefore the temperatureshould be decreased.II. Changing the temperature won’t change the fact that the ballis larger than the hole.III. Heating the brass plate makes its hole larger, and that willallow the ball to pass through.arrow_forwardcan you please work this out step by step please and do everythingarrow_forwardHi, kindly help me with this and show the complete solution. Thank youarrow_forward
- Please quicklyarrow_forwardConsider a solid sphere of radius R with a fixed surface temperature, TR. Heat is generated within the solid at a rate per unit volume given by q = ₁ + ₂r; where ₁ and ₂ are constants. (a) Assuming constant thermal conductivity, use the conduction equation to derive an expression for the steady-state temperature profile, T(r), in the sphere. (b) Calculate the temperature at the center of the sphere for the following parameter values: R=3 m 1₁-20 W/m³ TR-20 °C k-0.5 W/(m K) ₂-10 W/m³arrow_forwardStainless steel (AISI 304) ball bearings, which have been uniformly heated to 850°C, are hardened by quenching them in an oil bath that is maintained at 40°C. The ball diameter is 12.5 mm, and the convection coefficient associated with the oil bath is 1000 W/m².K. (a) If quenching is to occur until the surface temperature of the balls reaches 100°C, how long, in s, must the balls be kept in the oil? What is the center temperature, in °C, at the conclusion of the cooling period? (b) If 10,000 balls are to be quenched per hour, what is the rate at which energy must be removed, in kW, by the oil bath cooling system in order to maintain its temperature at 40°C? Evaluate the properties of the stainless steel (AISI 304) at 500 K. Part A If quenching is to occur until the surface temperature of the balls reaches 100°C, how long, in s, must the balls be kept in the oil? What is the center temperature, in °C, at the conclusion of the cooling period? t = T₁ = i i S °℃arrow_forward
- 8. The shown 2-D plate is in contact with a heat source at its upper edge, which supplies heat at a constant flux, qo, per unit length. -- a. Derive a finite-difference relationship to express the steady-state temperature at the shown boundary point TP, in terms of the temperatures at the surrounding points (TE, Tw, Ts) and the other quantities in the problem (e.g., k, qo, etc.). Follow the methodology outlined in the class notes (i.e., use energy balance). Assume Ax = Ay. y 90 b. Modify the relationship for the case when the upper edge is perfectly insulated (without heat addition).arrow_forwardPlease solve only part 3. This is a 3-part question involving heat transfer. Part 1 and 2 are correct, but I need help how to find part 3. Thank you.arrow_forwardNUMBER 4 A food product wants to be produced in a small round shape (pellet) by freezing it in a water blast freezer freezer. Air freezer operates at -30 ° C. The initial product temperature is 25 ° C. The pellet has a diameter of 0.5 cm, and a density of 980 kg / m³. The initial freezing temperature is -2.5 ° C. The latent heat of freezing of the product is 280 kJ / kg. The thermal conductivity of the frozen product is 1.9 W / (m ° C). The convective heat transfer coefficient is 50 W / (m² K). Calculate the freeze time. t f = hour.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license