Operations and Supply Chain Management, 9th Edition WileyPLUS Registration Card + Loose-leaf Print Companion
9th Edition
ISBN: 9781119371618
Author: Roberta S. Russell
Publisher: Wiley (WileyPLUS Products)
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 3, Problem 47P
Summary Introduction
To draw: The improvement required in the process of manufacturing baseballs to achieve the
Introduction: Statistical process control is a statistical technique used to analyze the functioning of production process. It helps to determine the factors that leads to poor quality in the production process. It also determines the measures that has to be taken in order to correct the production process.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Organic Grains LLC uses statistical process control to ensure that its health-conscious, low-fat, multigrain sandwich loaves have the proper weight.
Based on a previously stable and in-control process, the control limits of the x- and R-charts are:
UCL-4.86, LCL- = 4.52,
UCLR=1.344, LCLR = 0.
Over the past few days, they have taken five random samples of four loaves each and have found the following:
Based on the x-chart, is one or more samples beyond the control limits?
Sample
1
2
3
4
5
Yes
No
Loaf # 1
4.8
4.4
4.5
4.6
5.0
Net Weight
Loaf # 2
4.7
4.8
4.5
4.9
4.8
Loaf # 3
5.0
4.7
4.9
4.7
4.7
Loaf # 4
4.7
4.8
4.6
4.5
4.6
The Road King Tire Company in Birmingham wants to monitor the quality of the tires it manufactures. Each day the company quality-control manager takes a sample of 100 tires, tests them, and determines the number of defective tires. The results of 20 samples have been recorded as follows:
Sample
Number of Defectives
Sample
Number of Defectives
1
14
11
18
2
12
12
10
3
9
13
19
4
10
14
20
5
11
15
17
6
7
16
18
7
8
17
18
8
14
18
22
9
16
19
24
10
17
20
23
Construct a P -chart for this process using 2q limits and describe the variation in the process.
Note:-
Do not provide handwritten solution. Maintain accuracy and quality in your answer. Take care of plagiarism.
Answer completely.
You will get up vote for sure.
Auto pistons at Wemming Chung's plant in Shanghai are produced in a forging process, and the diameter is a critical factor
that must be controlled. From sample sizes of 5 pistons produced each day, the mean and the range of this diameter have
been as follows:
Day
Mean (mm)
Range R (mm)
158
4.3
151.2
4.4
155.7
4.2
153.5
4.8
156.6
4.5
What is the UCL using 3-sigma?(round your response to two decimal places).
1.
2.
4.
Chapter 3 Solutions
Operations and Supply Chain Management, 9th Edition WileyPLUS Registration Card + Loose-leaf Print Companion
Ch. 3.S - Prob. 1QCh. 3.S - Prob. 2QCh. 3.S - Prob. 3QCh. 3.S - Prob. 4QCh. 3.S - Prob. 5QCh. 3.S - Prob. 6QCh. 3.S - Prob. 7QCh. 3.S - The Great Lakes Company, a grocery store chain,...Ch. 3.S - Prob. 2PCh. 3.S - Prob. 3P
Ch. 3.S - The Fast Break Computer Company assembles personal...Ch. 3.S - Prob. 5PCh. 3 - Using Sampling and Statistics to Analyze...Ch. 3 - Prob. 2.1ASCCh. 3 - Prob. 3.1ASCCh. 3 - Prob. 4.1ASCCh. 3 - Prob. 5.1ASCCh. 3 - Prob. 1QCh. 3 - Prob. 2QCh. 3 - Prob. 3QCh. 3 - Prob. 4QCh. 3 - Prob. 5QCh. 3 - Prob. 6QCh. 3 - Prob. 7QCh. 3 - Prob. 8QCh. 3 - Prob. 9QCh. 3 - Prob. 10QCh. 3 - Prob. 11QCh. 3 - Prob. 1PCh. 3 - Prob. 2PCh. 3 - Prob. 3PCh. 3 - Prob. 4PCh. 3 - Prob. 5PCh. 3 - Prob. 6PCh. 3 - Prob. 7PCh. 3 - Prob. 8PCh. 3 - Prob. 9PCh. 3 - Prob. 10PCh. 3 - Prob. 11PCh. 3 - Prob. 12PCh. 3 - Prob. 13PCh. 3 - Prob. 14PCh. 3 - Prob. 15PCh. 3 - Prob. 16PCh. 3 - Prob. 17PCh. 3 - Prob. 18PCh. 3 - Prob. 20PCh. 3 - Prob. 21PCh. 3 - Prob. 22PCh. 3 - Prob. 23PCh. 3 - Prob. 24PCh. 3 - Prob. 25PCh. 3 - Prob. 26PCh. 3 - Prob. 27PCh. 3 - Prob. 28PCh. 3 - Prob. 29PCh. 3 - Prob. 30PCh. 3 - Prob. 32PCh. 3 - Prob. 33PCh. 3 - Prob. 34PCh. 3 - Prob. 36PCh. 3 - Prob. 37PCh. 3 - Prob. 38PCh. 3 - Prob. 39PCh. 3 - Prob. 40PCh. 3 - Elon Corporation manufactures parts for an...Ch. 3 - Prob. 42PCh. 3 - Prob. 44PCh. 3 - Prob. 45PCh. 3 - Prob. 46PCh. 3 - Prob. 47PCh. 3 - Metropolitan General Hospital is a city-owned...Ch. 3 - Prob. 50PCh. 3 - Prob. 51PCh. 3 - The Shuler Motor Mile is a high-volume discount...Ch. 3 - Prob. 1.1CPCh. 3 - Prob. 2.1CPCh. 3 - Improving Service Time at Daves Burgers Daves...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, operations-management and related others by exploring similar questions and additional content below.Similar questions
- 6 of 11 5 3. The manager of a building-supplies company randomly samples incoming lumber to see whether it meets quality specifications. From each shipment, 100 pieces of 2 x 4 lumber are inspected and judged according to whether they are first (acceptable) or second (defective) grade. The proportions of second-grade 2 x 4s recorded for 30 shipments were as follows: a. Construct a control chart for the proportion of second-grade 2 x 4s in samples of 100 pieces of lumber. b. Explain how the control chart can be of use to the manager of the building supplies company. Shipment No. Proportion of second grade 1 0.14 2 0.22 3 0.21 4 0.15 0.19 0.26 7 0.18 8 0.22 9 0.23 10 0.21 11 0.2 12 0.14 13 0.25 14 0.2 15 0.19 16 0.18 17 0.22 18 0.22 19 0.17 20 0.21 21 0.21 22 0.13 23 0.15 24 0.2 25 0.23 26 0.23 27 0.12 28 0.19 29 0.19 30 0.26arrow_forwardA. Choudhury’s bowling ball factory in Illinois makes bowling balls of adult size and weight only. The standard devia-tion in the weight of a bowling ball produced at the factory is known to be 0.12 pounds. Each day for 24 days, the averageweight, in pounds, of nine of the bowling balls produced that dayhas been assessed as follows: a) Establish a control chart for monitoring the average weights of the bowling balls in which the upper and lower control lim-its are each two standard deviations from the mean. What are the values of the control limits?b) If three standard deviations are used in the chart, how do thesevalues change? Why?arrow_forward4. Organic Grains LLC uses statistical process control to ensure that its health-conscious, low-fat, multigrain sandwich loaves have the proper weight. Based on a previously stable and in-control process, the control limits of the x- and R-charts are: UCLx = 5.35, LCLx = 4.93; UCLR = 0.894, LCLR = 0. Over the past few days, they have taken five random samples of four loaves each and have found the following: Net Weight Sample Loaf # 1 Loaf # 2 Loaf # 3 Loaf # 4 1 4.9 5.2 5.1 5.0 2 5.3 5.1 5.2 5.3 3 4.9 5.2 4.9 5.2 4 5.5 5.5 5.3 5.5 5 5.3 5.2 5.3 5.0 Part 2 Based on the x-chart, is one or more samples beyond the control limits? ▼ No Yes .arrow_forward
- C-Spec, Inc., is attempting to determine whether an existing machine is capable of milling an engine part that has a key specification of 3 ± 0.005 inches. After a trial run on this machine, C-Spec has determined that the machine has a sample mean of 3.004 inches with a standard deviation of 0.004 inch. a. Calculate the Cpk for this machine. (Round your answer to 3 decimal places.) Cpkarrow_forwardC-Spec, Inc., is attempting to determine whether an existing machine is capable of milling an engine part that has a key specification of 5 ± 0.006 inches. After a trial run on this machine, C-Spec has determined that the machine has a sample mean of 5.001 inches with a standard deviation of 0.005 inch. Calculate the Cpk for this machine. (Round your answer to 3 decimal places.)arrow_forwardThe objective of statistical process control (SPC) is to: Determine whether a batch of raw materials should be accepted or rejected. Determine whether a batch of finished goods should be accepted or rejected. Detect assignable cause variations versus normal random variations in the process. Identify variable versus attribute measures.arrow_forward
- A process filling small bottles with baby formula has a target of 3ounces ± 0.150 ounce. Two hundred bottles from the process were sampled. The results showed the average amount of formula placed in the bottles to be 3.042 ounces. The standard deviation of the amounts was 0.034 ounce. Determine the value of Cpk. Roughly what proportion of bottles meet the specifications? The process capability index (Cpk) is ?? enter your response here (round your response to three decimal places).▼ Slightly more than 80 , 99.99, 99.73, 9095.45 ?? %of the bottles meet the specifications. Which of the number above is slightly more than?arrow_forwardTwelve samples, each containing five parts, were taken from a process that produces steel rods at Emmanual Kodzi's factory. The length of each rod in the samples was determined. The results were tabulated and sample means and ranges were computed. The results were: Sample Sample Mean (in.) Range (in.) Sample Sample Mean (in.) Range (in.)1 9.700 0.044 7 9.703 0.0212 9.700 0.051 8 9.707 0.0583 9.689 0.042 9 9.695 0.0394 9.706 0.037 10…arrow_forwardDistinguish between a sampling error and a nonsampling error.How can each be reduced?arrow_forward
- Twelve samples, each containing five parts, were taken from a process that produces steel rods at Emmanual Kodzi's factory. The length of each rod in the samples was determined. The results were tabulated and sample means and ranges were computed. The results were: Sample Sample Mean (in.) Range (in.) Sample Sample Mean (in.) Range (in.) 1 9.602 0.033 7 9.603 0.041 2 9.602 0.041 8 9.605 0.034 3 9.593 0.034 9 9.597 0.027 4 9.606 0.051 10 9.601 0.029 5 9.599 0.031 11 9.603 0.039 6 9.599 0.036 12 9.606 0.047 Part 2 For the given data, the x double overbarx = (inches (round your response to four decimal places)arrow_forwardTwelve samples, each containing five parts, were taken from a process that produces steel rods at Emmanual Kodzi's factory. The length of each rod in the samples was determined. The results were tabulated and sample means and ranges were computed. The results were: Sample Sample Mean (in.) Range (in.) Sample Sample Mean (in.) Range (in.) 1 9.602 0.033 7 9.603 0.041 2 9.602 0.041 8 9.605 0.034 3 9.593 0.034 9 9.597 0.027 4 9.606 0.051 10 9.601 0.029 5 9.599 0.031 11 9.603 0.039 6 9.599 0.036 12 9.606 0.047 Part 2 For the given data, the x double overbarx = 9.6013 inches (round your response to four decimal places). Part 3 Based on the sampling done, the control limits for 3-sigma x overbarx chart are: Upper Control Limit (UCL Subscript x…arrow_forwardIn a sausage factory, quality managers are studying the compliance of the sausages with the requirements. Any sausage having pin holes, air pockets, deformation or breakage in its casings is counted as defective and total number of such defective sausages alone is noted in each shift. The following data represents the number of defective sausages in samples of 200 sausages taken from 10 shifts. Sample Defectives Percent Defective 1 40 20% 2 28 14% 3 15 8% 4 23 (a) 5 20 10% 6 21 11% 7 19 10% 8 15 8% 9 16 8% 10 17 9% Calculate the value for (a) in the table above. Calculate p-bar based on the samples above. What is the UCL and LCL for a p chart based on the data provided and a desired control level of 99.74%? Use your control limits from part b along with the data provided to draw a p-chart. Is the process in control? Why or why not? If not in control, suggest some potential reasons.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Practical Management ScienceOperations ManagementISBN:9781337406659Author:WINSTON, Wayne L.Publisher:Cengage,
Operations ManagementOperations ManagementISBN:9781259667473Author:William J StevensonPublisher:McGraw-Hill Education
Operations and Supply Chain Management (Mcgraw-hi...Operations ManagementISBN:9781259666100Author:F. Robert Jacobs, Richard B ChasePublisher:McGraw-Hill Education
Purchasing and Supply Chain ManagementOperations ManagementISBN:9781285869681Author:Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. PattersonPublisher:Cengage Learning
Production and Operations Analysis, Seventh Editi...Operations ManagementISBN:9781478623069Author:Steven Nahmias, Tava Lennon OlsenPublisher:Waveland Press, Inc.
Practical Management Science
Operations Management
ISBN:9781337406659
Author:WINSTON, Wayne L.
Publisher:Cengage,
Operations Management
Operations Management
ISBN:9781259667473
Author:William J Stevenson
Publisher:McGraw-Hill Education
Operations and Supply Chain Management (Mcgraw-hi...
Operations Management
ISBN:9781259666100
Author:F. Robert Jacobs, Richard B Chase
Publisher:McGraw-Hill Education
Purchasing and Supply Chain Management
Operations Management
ISBN:9781285869681
Author:Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. Patterson
Publisher:Cengage Learning
Production and Operations Analysis, Seventh Editi...
Operations Management
ISBN:9781478623069
Author:Steven Nahmias, Tava Lennon Olsen
Publisher:Waveland Press, Inc.