Determine the convection heat loss from both the top and the bottom of a flat plate at
Want to see the full answer?
Check out a sample textbook solutionChapter 7 Solutions
Fundamentals of Heat and Mass Transfer
Additional Engineering Textbook Solutions
Engineering Mechanics: Dynamics (14th Edition)
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
Applied Fluid Mechanics (7th Edition)
Manufacturing Engineering & Technology
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
- Evaluate the capillary number for water at 20°C and a velocity of 5 cm/s. For water at 20°C, p = 0.001 kg/m-s and Y= 0.0728 N/m.arrow_forward(a) A space of 25 mm width between two surfaces filled with SAE 30 western lubricating oil at 250C (u = 0.18 Ns/m?). Plot the velocity profile and determine the force which is required to drag a thin plate (speed = 0.4 m/s) of 0.35 m? area located at a distance of 10 mm from the top plate i. If the surfaces are fixed ii. If the top surface is fixed and bottom surface is moving at a constant velocity of 0.1 m/s in the direction of the plate = 4 = iii. If the top surface is fixed and bottom surface is moving at a constant velocity of 0.1 m/s in the opposite direction of the platearrow_forwardA submarine can be treated as an ellipsoid with a diameter of 5 m and a length of 25 m. The submarine is cruising horizontally and steadily at 65 km/h in seawater (p = 1025 kg/m³.p = 0.00108 Ns/m2). Determine: The Reynolds number for the submarine and state whether the flow is in the laminar or turbulent regime. ii. The drag force on the submarine. iii. The power required to overcome the drag force. To surface, a total lift force of 1000 kN is required from a pair of NACA 0012 hydroplanes. Each hydroplane has a chord length of 1 m and a iv. span of 3 m. What angle of attack should be used?arrow_forward
- [1] A Newtonian fluid with a viscosity u and density p, is flowing at a laminar condition on an inclined plate with the length Land width W at a temperature T as shown in the figure. The fluid layer on the plate has a thickness of d. Establish the mass, energy, and momentum balances based on the given system. Draw the velocity and shear stress profiles. H, P AP Øm2arrow_forwardA 20degC water flows to 50cmx60cm flat plate with velocity of 3m/s . The flat plate surface temperature is maintained at 40deg C. The air flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, at what length the flow become turbulent? Round your answer to 2 decimal places.arrow_forwardA 0.5m x 2m flat thin plate is moved at 5m/s on a 2-mm thick layer of SAE 30 oil at 38 degrees Celsius that separates it from a flat surface. The velocity distribution between the plate and the surface is assumed to be linear. What force is required if the plate and surface are horizontal? (μSAE30 = 0.1 N-s/m2)arrow_forward
- -If the velocity distribution for the laminar boundary layer over a flat plate is given by :- 3 2 U x - 4 4 - (2) + 4 - (H) + 4 (2) + 22 X x U∞o Determine the form of the velocity profile by using the necessary boundary conditions. After that by using the Von- Karman integral momentum equation find an expression in terms of the Reynolds number to evaluate 1- Boundary Layer Thickness Force 4- Local and Average Skin Friction Coefficients 6- Momentum Thickness 7- Energy Thickness 2-Wall Shear Stress 3- Drag 5- Displacement Thicknessarrow_forwardOne dimensional flow occurs in the circular tube at the location adequately far from the entrance shown in the figure right. Velocity profile is the laminar and expressed as; U(x) = Umax (1-r/R?) Where R: radius of the tube, r: distance beginning from the center and Umax : maximum velocity (at the center). Drive the expression for the drag force per unit area applied to both plates by the flu id (F/A). If the drag force is 0.565 N, calculate the necessary velocity for the water at 20°C flow through the tube with the radius of 0.08 m and 15 m length (u:0.0010 kg/m. s). R -Umaxarrow_forwardAir is flowing parallel to the plate at U∞=5 m/s and T∞=300 K over the flat plate of length L=0.1 m anddepth of 1 m into the paper, at the atmospheric pressure at the same temperature as the plate. Find;a) Boundary layer thickness at the point x = L of the plateb) Find the total resistance force acting on the two surfaces of the plate.c) The velocities in the hydrodynamic boundary layer are measured by a hot wire anomemeter. Thevelocity at x=0.1 m on the x component is measured as u=3 m/s. Find the distance from the plate and they component of velocity v.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY