Consider an opaque, gray surface whose directional absorptivity is 0.8 for 0 ≤ θ ≤ 60 ∘ and θ > 60 ∘ . The surface is horizontal and exposed to solar irradiation comprised of direct and diffuse components. (a) What is the surface absorptivity to direct solar radiation that is incident at an angle of 45 ∘ C from the normal? What is the absorptivity to diffuse irradiation? (b) Neglecting convection heat transfer between the surface and the surrounding air, what would be the equilibrium temperature of the surface if the direct and diffuse components of the irradiation were 600 and 100 W / m 2 , respectively? The back side of the surface is insulated.
Consider an opaque, gray surface whose directional absorptivity is 0.8 for 0 ≤ θ ≤ 60 ∘ and θ > 60 ∘ . The surface is horizontal and exposed to solar irradiation comprised of direct and diffuse components. (a) What is the surface absorptivity to direct solar radiation that is incident at an angle of 45 ∘ C from the normal? What is the absorptivity to diffuse irradiation? (b) Neglecting convection heat transfer between the surface and the surrounding air, what would be the equilibrium temperature of the surface if the direct and diffuse components of the irradiation were 600 and 100 W / m 2 , respectively? The back side of the surface is insulated.
Solution Summary: The author explains the absorptivity of an opaque, gray surface to direct solar radiation and to diffuse irradiation.
Consider an opaque, gray surface whose directional absorptivity is 0.8 for
0
≤
θ
≤
60
∘
and
θ
>
60
∘
. The surface is horizontal and exposed to solar irradiation comprised of direct and diffuse components.
(a) What is the surface absorptivity to direct solar radiation that is incident at an angle of
45
∘
C
from the normal? What is the absorptivity to diffuse irradiation?
(b) Neglecting convection heat transfer between the surface and the surrounding air, what would be the equilibrium temperature of the surface if the direct and diffuse components of the irradiation were 600 and
100
W
/
m
2
, respectively? The back side of the surface is insulated.
A piston–cylinder device contains 50 kg of water at 250 kPa and 25°C. The cross-sectional area of the piston is 0.1 m2. Heat is now transferred to the water, causing part of it to evaporate and expand. When the volume reaches 0.26 m3, the piston reaches a linear spring whose spring constant is 100 kN/m. More heat is transferred to the water until the piston rises 20 cm more.
NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.
Determine the work done during this process.
The work done during this process is kJ.
A 4-m × 5-m × 7-m room is heated by the radiator of a steam-heating system. The steam radiator transfers heat at a rate of 10,000 kJ/h, and a 100-W fan is used to distribute the warm air in the room. The rate of heat loss from the room is estimated to be about 5000 kJ/h. If the initial temperature of the room air is 10°C, determine how long it will take for the air temperature to rise to 25°C. Assume constant specific heats at room temperature. The gas constant of air is R = 0.287 kPa·m3/kg·K (Table A-1). Also, cv = 0.718 kJ/kg·K for air at room temperature (Table A-2).
Steam enters the radiator system through an inlet outside the room and leaves the system through an outlet on the same side of the room. The fan is labeled as W sub p w. The heat is given off by the whole system consisting of room, radiator and fan at the rate of 5000 kilojoules per hour.
It will take 831 Numeric ResponseEdit Unavailable. 831 incorrect.s for the air temperature to rise to 25°C.
A piston–cylinder device contains 50 kg of water at 250 kPa and 25°C. The cross-sectional area of the piston is 0.1 m2. Heat is now transferred to the water, causing part of it to evaporate and expand. When the volume reaches 0.26 m3, the piston reaches a linear spring whose spring constant is 100 kN/m. More heat is transferred to the water until the piston rises 20 cm more.
NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.
Determine the final pressure and temperature.
The final pressure is kPa.
The final temperature is ºC.
Find the work done during the process
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.