Fundamentals of Heat and Mass Transfer
7th Edition
ISBN: 9780470917855
Author: Bergman, Theodore L./
Publisher: John Wiley & Sons Inc
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 12, Problem 12.110P
Consider the evacuated tube solar collector described in part (d) of Problem 1.87 of Chapter 1. In the interest of maximizing collector efficiency, what spectral radiative characteristics are desired for the outer tube and for the inner tube?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A thin, disk-shaped silicon wafer of diameter D=20 cm on a production line must be maintained at a temperature of 100 deg C. The wafer loses heat to the room by convection and radiation from its upper surface, while heat is supplied at a constant flux from below. The surrounding air is at 20 deg C, while all surrounding surfaces (which can be treated as blackbodies) can be approximated to be isothermal at a temperature of 15 deg C. The wafer-to-air heat transfer coefficient is 30 W/m2-K and the emissivity of the wafer’s surface (which can be approximated to be gray) is 0.85. How much heat (in W) must be supplied to the wafer?
A gray surface has an emissivity at a temperature of 550 K source. If the surface is opaque,
(a) Calculate its reflectivity for black body radiation coming from a 550 K source.
(b) A small 25 mm square hole is made in the thin-walled door of a furnace whose inside walls are at 920 K. if the emissivity of the walls is 0.72, calculate the rate at which radiant energy escapes from the furnace through the hole to the room.
I need the solution in hand writing
Chapter 12 Solutions
Fundamentals of Heat and Mass Transfer
Ch. 12 - Consider an opaque horizontal plate that is well...Ch. 12 - A horizontal, opaque surface at a steady-state...Ch. 12 - The top surface of an L=5mmthick anodized aluminum...Ch. 12 - A horizontal semitransparent plate is uniformly...Ch. 12 - What is the irradiation at surfaces A2 , A3 , and...Ch. 12 - According to its directional distribution, solar...Ch. 12 - Solar radiation incident on the earth’s surface...Ch. 12 - On an overcast day the directional distribution of...Ch. 12 - During radiant heat treatment of a thin-film...Ch. 12 - A small radiant heat source of area A1=2x104m2...
Ch. 12 - Determine the fraction of the total, hemispherical...Ch. 12 - The spectral distribution of the radiation emitted...Ch. 12 - Consider a 5-mm-square, diffuse surface A0 having...Ch. 12 - Assuming blackbody behavior, determine the...Ch. 12 - The dark surface of a ceramic stove top may be...Ch. 12 - The energy flux associated with solar radiation...Ch. 12 - A small flat plate is positioned just beyond the...Ch. 12 - A spherical aluminum shell of inside diameter D=2m...Ch. 12 - The extremely high temperatures needed to trigger...Ch. 12 - An enclosure has an inside area of 100m2 , and its...Ch. 12 - Assuming the earth’s surface is black, estimate...Ch. 12 - A proposed method for generating electricity from...Ch. 12 - Approximations to Planck’s law for the spectral...Ch. 12 - Estimate the wavelength corresponding to maximum...Ch. 12 - A furnace with a long, isothermal, graphite tube...Ch. 12 - Isothermal furnaces with small apertures...Ch. 12 - For materials A and B, whose spectral...Ch. 12 - A small metal object, initially at Ti=1000K ,is...Ch. 12 - The directional total emissivity of nonmetallic...Ch. 12 - Consider the metallic surface of Example 12.7....Ch. 12 - The spectral, directional emissivity of a diffuse...Ch. 12 - Consider the directionally selective surface...Ch. 12 - A sphere is suspended in air in a dark room and...Ch. 12 - Estimate the total, hemispherical emissivity for...Ch. 12 - Sheet steel emerging from the hot roll section of...Ch. 12 - A large body of nonluminous gas at a temperature...Ch. 12 - An opaque surface with the prescribed spectral,...Ch. 12 - The spectral reflectivity distribution for white...Ch. 12 - A diffuse, opaque surface at 700 K has spectral...Ch. 12 - The spectral, hemispherical absorptivity of an...Ch. 12 - The spectral, hemispherical absorptivity of an...Ch. 12 - Consider an opaque, diffuse surface for which the...Ch. 12 - Radiation leaves a furnace of inside surface...Ch. 12 - The spectral transmissivity of a 1-mm-thick layer...Ch. 12 - The spectral transmissivity of plain and tinted...Ch. 12 - Referring to the distribution of the spectral...Ch. 12 - The spectral absorptivity and spectral...Ch. 12 - Consider a large furnace with opaque, diffuse,...Ch. 12 - Four diffuse surfaces having the spectral...Ch. 12 - The spectral transmissivity of a 50m -thick...Ch. 12 - An opaque, horizontal plate has a thickness of...Ch. 12 - Two small surfaces, A and B, are placed inside an...Ch. 12 - Consider an opaque, diffuse surface whose spectral...Ch. 12 - The 50-mm peephole of a large furnace operating at...Ch. 12 - The window of a large vacuum chamber is fabricated...Ch. 12 - A thermograph is a device responding to the...Ch. 12 - A radiation thermometer is a radiometer calibrated...Ch. 12 - A radiation detector has an aperture of area...Ch. 12 - A small anodized aluminum block at 35C is heated...Ch. 12 - Consider the diffuse, gray opaque disk A1 , which...Ch. 12 - A two-color pyrometer is a device that is used to...Ch. 12 - An apparatus commonly used for measuring the...Ch. 12 - A procedure for measuring the thermal conductivity...Ch. 12 - One scheme for extending the operation of gas...Ch. 12 - The equipment for heating a wafer during a...Ch. 12 - Neglecting the effects of radiation absorption,...Ch. 12 - Consider the evacuated tube solar collector...Ch. 12 - Solar flux of 900W/m2 is incident on the top side...Ch. 12 - Consider an opaque, gray surface whose directional...Ch. 12 - A contractor must select a roof covering material...Ch. 12 - It is not uncommon for the night sky temperature...Ch. 12 - Plant leaves possess small channels that connect...Ch. 12 - In the central receiver concept of solar energy...Ch. 12 - Radiation from the atmosphere or sky can be...Ch. 12 - A thin sheet of glass is used on the roof of a...Ch. 12 - Growers use giant fans to prevent grapes from...Ch. 12 - A circular metal disk having a diameter of 0.4 m...Ch. 12 - The neighborhood cat likes to sleep on the roof of...Ch. 12 - The exposed surface of a power amplifier for an...Ch. 12 - Consider a thin opaque, horizontal plate with an...Ch. 12 - The oxidized-aluminum wing of an aircraft has a...Ch. 12 - Two plates, one with a black painted surface and...Ch. 12 - A radiator on a proposed satellite solar power...Ch. 12 - A radiator on a proposed satellite solar power...Ch. 12 - A spherical satellite in near-earth orbit is...Ch. 12 - An annular fin of thickness t is used as a...Ch. 12 - The directional absorptivity of a gray surface...Ch. 12 - Two special coatings are available for application...Ch. 12 - Consider the spherical satellite of Problem...Ch. 12 - A spherical capsule of 3-m radius is fired from a...Ch. 12 - Consider the spherical satellite of Problem...Ch. 12 - A solar panel mounted on a spacecraft has an area...Ch. 12 - It is known that on clear nights a thin layer of...Ch. 12 - A shallow layer of water is exposed to the natural...Ch. 12 - A roof-cooling system, which operates by...Ch. 12 - A wet towel hangs on a clothes line under...Ch. 12 - Our students perform a laboratory experiment to...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
3.3 It is known that a vertical force of 200 lb is required to remove the nail at C from the board. As the nail...
Vector Mechanics for Engineers: Statics, 11th Edition
Assume the following vectors are already defined: V1=[302]V2=[214]V3=[5131]V4=[0.50.10.20.2] For each of the fo...
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
How is the hydrodynamic entry length defined for flow in a pipe? Is the entry length longer in laminar or turbu...
Fluid Mechanics Fundamentals And Applications
Define or describe each type of fluid: (a) viscoelastic fluid (b) pseudoplastic fluid (c) dilatant fluid (d) Bi...
Fluid Mechanics: Fundamentals and Applications
Find the change in length of side AB.
Mechanics of Materials, 7th Edition
A number of common substances are
Some of these materials exhibit characteristics of both solid and fluid beha...
Fox and McDonald's Introduction to Fluid Mechanics
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 11.31 A large slab of steel 0.1 m thick contains a 0.1 -m-di- ameter circular hole whose axis is normal to the surface. Considering the sides of the hole to be black, specify the rate of radiative heat loss from the hole. The plate is at 811 K, and the surroundings are at 300 K.arrow_forwardA tungsten filament is heated to 2700 K. At what wavelength is the maximum amount of radiation emitted? What fraction of the total energy is in the visible range (0.4to0.75m)? Assume that the filament radiates as a graybody.arrow_forwardTwo large parallel plates with surface conditions approximating those of a blackbody are maintained at 816C and 260C, respectively. Determine the rate of heat transfer by radiation between the plates in W/m2 and the radiative heat transfer coefficient in W/m2K.arrow_forward
- Light from an ideal spherical blackbody 15.0 cm in diameteris analyzed by using a diffraction grating that has 3850 lines/cm.When you shine this light through the grating, you observe that thepeak-intensity wavelength forms a first-order bright fringe at +-14.4 from the central bright fringe. (a) What is the temperature of the blackbody?(b) How long will it take this sphere to radiate 12.0 MJ of energyat constant temperature?arrow_forward3. A star has a surface temperature of 5,500K. Determine the radiative heat transfer received by planet Z in Petawatts with diameter of 2100 km, temperature of surface of 300K and mean absorptivity of 0.8. Radiative energy loss due to radiation dispersion on outer space is 99%.arrow_forwardTwo infinite black plates (ɛ,=1.0) at 800-C and 300-C exchange heat by radiation. Calculate the heat transfer per unit area.(Hint use q/A= E: o(T:* – T), convert to Kelvin before substituting)arrow_forward
- A typical car's exterior consists of a thin layer of silica (SiO2) over an opaque painted metal panel. Silica is transparent in the visible wavelengths but offers high reflectance in the near- to mid- infrared wavelengths. The plot on the next page depicts the diffuse spectral reflectivity (pa) of the car's surface: Spectral reflectivity, P₂ 0.8 0.6 0.4 ལ 0.2 0 0.1 1 1 10 Wavelength, λ(μm) 100 If the car's exterior temperature is T₁ = 77°C, determine both the total absorptivity (a) and the total emissivity (a) of the silica-covered panel. Assume that the Sun's temperature is Tsun = 5800 K.arrow_forward6.4 Two large diffuse parallel plates are maintained at temperatures T₁ = 1400 K and T₂ = 700 K. The plates are made from the same metal, and their spectral emissivities as a function of wavelength, &, are approximated as shown by two constant values joined by a linear decrease with wavelength. Compute the net radiant energy flux being transferred from plate 1 to plate 2. What is the energy flux if both plates are assumed gray with an approximate average emissiv- ity of 0.5 applied over the entire spectral range? 91 T₁ = 1400 K, Ex T₂ = 700 K, EX 92-91 0.85 Ex 0.15 0 Answer: q₁106,850 W/m²; 91.gray = 68,070 W/m². 2 λ (μm) 7arrow_forwardA drying oven consists of a long semicircular duct of diameter D=1 m. Materials to be dried cover the base of the oven while the wall is maintained at 1200 K. Length of the oven (into paper direction) is 1 m. Water coated material is maintained at 325 K. Assume both the wall and the material to be blackbodies. (1) What is heat transfer rate? (2) Given at temperature 325 K, water needs heat 2.378 × 106 J/kg in order to be dried (from liquid water to steam). How much water can be dried per second based on the heat transfer rate from (1)? T₁ = 1200 K T₂ = 325 K — D = 1 m D= m→arrow_forward
- An engineered passive radiative cooler coating is placed under the Sun. Provided the following simplified spectral emissivity/absorptivity plot below, calculate the total diffuse emissivity and absorptivity if its uniform surface temperature is a Ts=20°C. Assume the Sun's irradiation onk Earth is Gsun=1380 W/m2 and its blackbody temperature is Tsun= 5800K. Ignore the radiation from the atmosphere (surroundings).arrow_forwardThe last portion asks you for "net radiant heat flux to the surface", meaning that positive net radiative heat flux means in and negative net radiative heat flux means out. This is opposite the typical sign convention - be aware of thisarrow_forwardPravinbhaiarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Understanding Thermal Radiation; Author: The Efficient Engineer;https://www.youtube.com/watch?v=FDmYCI_xYlA;License: Standard youtube license