A dormitory at a large university, built 50 years ago, has exterior walls constructed of
Want to see the full answer?
Check out a sample textbook solutionChapter 3 Solutions
Fundamentals of Heat and Mass Transfer
- A cylindrical electrical heating element is used to heat up a baking oven. The heating element bears a voltage of 120 V/m, and has an electrical resistance of 1000 Ω/m. A ceramic pipe of inside radius rin = 2 mm, and outside radius rout = 5 mm encases the heating element. Thermal conductivity of the ceramic is k = 0.2 W/m-K. Given that the oven air temperature is T∞ = 180oC and convection coefficient h = 10 W/m2-K, find the temperature on the inside of the ceramic pipe.arrow_forwardA dormitory at a large university, built 50 years ago, has exterior walls constructed of Ls = 25-mm-thick sheathing with a thermal conductivity of ks = 0.1 W/m-K. To reduce heat losses in the winter, the university decides to encapsulate the entire dormitory by applying an L; = 25-mm-thick layer of extruded insulation characterized by k; = 0.029 W/m-K to the exterior of the original sheathing. The extruded insulation is, in turn, covered with an Lg = 5-mm-thick architectural glass with kg the heat flux through the original and retrofitted walls when the interior and exterior air temperatures are Ti = 22°C and T.o -2.5°C, respectively. The inner and outer convection heat transfer coefficients are h; = 5W/m2-K and ho = 1.4 W/m-K. Determine 25 W/m2-K, respectively. The heat flux through the original walls is i W/m?. The heat flux through the retrofitted walls is i W/m?.arrow_forwardA 3 inch schedule 40 pipe is covered with two layers of insulations. The inner layer (k1 = 0.050) is 2 inches thick and the outer layer (k2 = 0.037) is 1(1/4) inches thick. Calculate the heat loss, in Btu/hr per unit length, if the outer surface temperature of the pipe is 670°F and the outer surface temperature of the outer layer of insulation is 100°F.arrow_forward
- QUESTION 2 The wall of a refrigerated truck consists of 1.5mm sheet steel outer surface, 10mm plywood at the inner surface and 20mm of glass wool in between. The inside temperature is -15°C and outside temperature is 240C. Take the thermal conductivities of the materials as follows: - 0,052W/mK = 23,2W/mK k for glass-wool = 0,14W/mK k for plywood k for steel %3D %3D %3D Calculate: 2.1. the rate of heat flow per unit area; 2.2. the interface temperature. If the glass-wool is replaced by a 5mm cork board with a thermal conductivity of 0.043W/mK; 2.3. What percentage change in heat flow is obtained? 2.4. What must be the thickness of the cork board be, to achieve the same heat flow as in (2.1.).arrow_forwardConsider two concentric spheres of radii R1 and R2 (R1<R2). The inner sphere has a temperature of T1=20°C and the outer sphere has a temperature of T2=100°C. The material between the two spheres has a thermal conductivity of k=0.5 W/(m⋅K). Calculate the heat flow from the outer sphere to the inner sphere. Determine the equation of the thermal Ohm's law for this system.arrow_forwardConsider a composite wall of overall height H = 30 mm and thickness L = 40 mm. Section A hasthickness LA = 15 mm and thermal conductivity of 3 W/(m·K). Sections B and C each have heightHB = 15 mm and thickness LB = 25 mm. The thermal conductivity is 1 W/(m·K) in section B and 2W/(m·K) in section C. The temperatures of the left and right faces of the composite wall are T1 =60°C and T2 = 30°C, respectively. The top and bottom of the wall are insulated. A) Draw a thermal circuit based on heat flux for the composite wall shown above.Assume that the temperature is uniform “vertically” in material A. Indicate thetemperatures, thermal resistances, and heat flux in the circuit diagram. Show theequations for the thermal resistances in the circuits. Do NOT need to perform anycalculations in this part.B. Draw a thermal circuit based on heat flux for the composite wall shown above.Assume that the temperature is NOT uniform “vertically” in material A and heat onlyflows along horizontal direction.…arrow_forward
- A thick-walled tube of stainless steel with thermal conductivity k = 19 W/m°C has inner diameter of 10 em and outer diameter of 30 em is covered with 5 cm layer of asbestos insulation with thermal conductivity k = 0.2 W/m°C. If the inside of the pipe and outside of insulator temperature is maintained at 600°C and 106 °C respectively. Determine the heat loss per meter length of pipe and the tube-insulation interface temperature.arrow_forwarda flat wall is covered with a layer of insulation 1.0 in. thick whose thermal conductivity is 0.8 Btu/hr-ft- F. the temperature of the wall on the inside of the insulation is 600F. the wall loses heat to the environment by convection on the surface of the insulation. the average value of the convection heat transfer coefficient on the inslation surface is 950 Btu/hr-ft^2-F. compute the bulk temperature of the environment if the outer surface of the insulation does not exceed 105 F.arrow_forwardX Your answer is incorrect. A dormitory at a large university, built 50 years ago, has exterior walls constructed of L, = 25-mm-thick sheathing with a thermal conductivity of k, = 0.1 W/m-K. To reduce heat losses in the winter, the university decides to encapsulate the entire dormitory by applying an L; = 25-mm-thick layer of extruded insulation characterized by k; = 0.029 W/m-K to the exterior of the original sheathing. The extruded insulation is, in turn, covered with an Lg = 5-mm-thick architectural glass with kg = 1.4 W/m-K. Determine the heat flux through the original and retrofitted walls when the interior and exterior air temperatures are T = 22°C and To = O°C, respectively. The inner and outer convection heat transfer coefficients are h; = 5 W/m?-Kand h, 00, 25 W/m2-K, respectively. The heat flux through the original walls is 1.46 W/m?. The heat flux through the retrofitted walls is 0.92 W/m?.arrow_forward
- Steel pipe (outer diameter 100 mm) is covered with two layers of insulation. The inner layer, 40 mm thick, has a thermal conductivity of 0.07 W / (m K). The outer layer, 20 mm thick, has a thermal conductivity of 0.15 W / (m K). Pipes are used to deliver steam with a pressure of 600 kPa. The temperature on the outer insulation surface is 24 ° C. If the pipe is 8 m long, determine the following: (assuming that the conduction heat transfer resistance of the steel pipe and the vapor convection resistance are negligible). a. Heat loss per hour. = kJ / hour. b. Temperature between insulation layers. = ° Carrow_forwardSteel pipe (outer diameter 100 mm) is covered with two layers of insulation. The inner layer, 40 mm thick, has a thermal conductivity of 0.07 W / (m K). The outer layer, 20 mm thick, has a thermal conductivity of 0.15 W / (m K). Pipes are used to deliver steam with a pressure of 500 kPa. The temperature on the outer insulation surface is 24 ° C. If the pipe is 8 m long, determine the following: (assuming that the conduction heat transfer resistance of the steel pipe and the vapor convection resistance are negligible). a. Heat loss per hour. = Answer kJ / hour. b. Temperature between insulation layers. = Answer ° C.arrow_forwardA steel pipe (outside diameter 100 mm) is covered with two layers of insulation. The inside layer, 40 mm thick, has a thermal conductivity of 0.07 W/(m K). The outside layer, 20 mm thick, has a thermal conductivity of 0.15 W/(m K). The pipe is used to convey steam at a pressure of 600 kPa. The outside temperature of insulation is 24°C. If the pipe is 10 m long, determine the following, assuming the resistance to conductive heat transfer in steel pipe and convective resistance on the steam side are negligible: a. The heat loss per hour. b. The interface temperature of insulation.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY