
Microelectronics: Circuit Analysis and Design
4th Edition
ISBN: 9780073380643
Author: Donald A. Neamen
Publisher: McGraw-Hill Companies, The
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 8, Problem 8.27P
(a)
To determine
Theexpression for the value of the voltage
(b)
To determine
The value of the maximum output voltage, the values of
Expert Solution & Answer

Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Q2. Figure Q2 shows a block diagram with an input of C(s) and an output R(s).
a)
C(s)
K₁
R(s)
K2
1 + 5s
1+2s
Figure Q2. Block diagram of control system.
Simply the block diagram to get the transfer function of the system C(s)/R(s).
b)
What is the order of the system?
c)
What is the gain of the system?
d) Determine the values of K₁ and K₂ to obtain a natural frequency w of
0.5 rad/s and damping ratio of 0.4.
e) What is the rise time and overshoot of the system with a unit step input?
Q4.
a) A purely derivative controller (i.e. with a zero at the origin only) is defined
by an improper transfer function. Considering its asymptotic behaviour,
explain why a purely derivative controller is difficult to implement in
practice. Relate your explanation to the potential limitations on system
performance.
b) Discuss the potential issues faced by a control system with a large cut-off
frequency. Relate your discussion to the implications on system
performance.
c)
The transfer function of a lag compensator is given by
2
KPID(S) = 2.2++0.2s
S
By using the asymptotic approximation technique:
(i) Obtain the standard form and corner frequency for each individual
component of KPID(S).
(ii) Clearly describe the asymptotic behaviour of each individual
component of KPID(S).
Module Code: EN2058
Q1. a) List the advantages and disadvantages of a closed loop system compared to
an open loop system.
b)
c)
What is the procedure for designing a control system for a bread toaster?
An RC circuit is given in Figure Q1. vi(t) and v(t) are the input and output
voltages.
(i) Derive the transfer function of the circuit.
(ii) With a unit step change vi(t) applied to the circuit, derive and sketch the
time response of the circuit.
R1 R2
v₁(t)
R3 C1
vo(t)
R₁ =R2 = 10 k
R3 = 100 kn C₁ = 100 μF
Figure Q1. RC circuit.
(iii) Assuming zero initial conditions, obtain the impulse and ramp responses
of the circuit from the step response derived in (ii). Sketching is not
needed.
Chapter 8 Solutions
Microelectronics: Circuit Analysis and Design
Ch. 8 - Prob. 8.1EPCh. 8 - Prob. 8.2EPCh. 8 - Prob. 8.3EPCh. 8 - Prob. 8.1TYUCh. 8 - Prob. 8.2TYUCh. 8 - Prob. 8.3TYUCh. 8 - Prob. 8.4EPCh. 8 - Prob. 8.5EPCh. 8 - Prob. 8.7EPCh. 8 - Prob. 8.4TYU
Ch. 8 - Prob. 8.5TYUCh. 8 - Prob. 8.6TYUCh. 8 - A transformercoupled emitterfollower amplifier is...Ch. 8 - Prob. 8.7TYUCh. 8 - Prob. 8.9EPCh. 8 - Prob. 8.11EPCh. 8 - Consider the classAB output stage shown in Figure...Ch. 8 - From Figure 8.36, show that the overall current...Ch. 8 - Prob. 1RQCh. 8 - Describe the safe operating area for a transistor.Ch. 8 - Why is an interdigitated structure typically used...Ch. 8 - Discuss the role of thermal resistance between...Ch. 8 - Define and describe the power derating curve for a...Ch. 8 - Define power conversion efficiency for an output...Ch. 8 - Prob. 7RQCh. 8 - Describe the operation of an ideal classB output...Ch. 8 - Discuss crossover distortion.Ch. 8 - What is meant by harmonic distortion?Ch. 8 - Describe the operation of a classAB output stage...Ch. 8 - Describe the operation of a transformercoupled...Ch. 8 - Prob. 13RQCh. 8 - Sketch a classAB complementary MOSFET pushpull...Ch. 8 - What are the advantages of a Darlington pair...Ch. 8 - Sketch a twotransistor configuration using npn and...Ch. 8 - Prob. 8.1PCh. 8 - Prob. 8.2PCh. 8 - Prob. 8.3PCh. 8 - Prob. 8.4PCh. 8 - Prob. 8.5PCh. 8 - Prob. D8.6PCh. 8 - A particular transistor is rated for a maximum...Ch. 8 - Prob. 8.8PCh. 8 - For a power MOSFET, devcase=1.5C/W , snkamb=2.8C/W...Ch. 8 - Prob. 8.10PCh. 8 - The quiescent collector current in a BiT is ICQ=3A...Ch. 8 - Prob. 8.12PCh. 8 - Prob. 8.13PCh. 8 - Prob. 8.14PCh. 8 - Prob. 8.15PCh. 8 - Prob. 8.16PCh. 8 - Consider the classA sourcefollower circuit shown...Ch. 8 - Prob. 8.18PCh. 8 - Prob. 8.19PCh. 8 - Prob. 8.20PCh. 8 - Prob. 8.21PCh. 8 - Consider an idealized classB output stage shown in...Ch. 8 - Consider an idealized classB output stage shown in...Ch. 8 - Prob. 8.24PCh. 8 - For the classB output stage shown in Figure P8.24,...Ch. 8 - Prob. 8.26PCh. 8 - Prob. 8.27PCh. 8 - Consider the classAB output stage in Figure P8.28....Ch. 8 - Prob. 8.29PCh. 8 - Prob. D8.30PCh. 8 - Prob. 8.31PCh. 8 - Prob. D8.32PCh. 8 - Consider the transformercoupled commonemitter...Ch. 8 - The parameters for the transformercoupled...Ch. 8 - A BJT emitter follower is coupled to a load with...Ch. 8 - Consider the transformercoupled emitter follower...Ch. 8 - A classA transformer-coupled emitter follower must...Ch. 8 - Repeat Problem 8.36 if the primary side of the...Ch. 8 - Consider the circuit in Figure 8.31. The circuit...Ch. 8 - Prob. D8.40PCh. 8 - The value of IBiass in the circuit shown in Figure...Ch. 8 - The transistors in the output stage in Figure 8.34...Ch. 8 - Consider the circuit in Figure 8.34. The supply...Ch. 8 - Prob. 8.44PCh. 8 - Prob. 8.45PCh. 8 - Consider the classAB MOSFET output stage shown in...Ch. 8 - Prob. 8.47PCh. 8 - Consider the classAB output stage in Figure P8.48....Ch. 8 - For the classAB output stage in Figure 8.36, the...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Q3. a) The frequency response method enables the study of the steady-state response of a system G(s). What type of inputs are used for frequency response? If the system is linear and stable, how does the output differ from the input? Compare the main characteristics of two types frequency response plots. b) Consider the control system shown in Figure Q3. Controller E(s) R(s) Desired output C(s) Plant G(s) Y(s) Actual output 3(s + 3) C(s) = k G(s) = = s(s - 1)(s + 10) Figure Q3. Closed-loop system. (i) Considering definitions in the study of bounded-input bounded-output stability, is G(s) stable? Classify the poles and zeros of G(s). (ii) G(s) defined in Figure Q3 is a system completely characterised by its transfer function. Explain why this is the case. (iii) Obtain the closed-loop transfer function P(s) = Y(s)/R(s) of the system. (iv) Based on your result for the previous question [Question 3b)-(iii)], use the Routh-Hurwitz stability criterion to determine suitable values of gain K…arrow_forwardPlease, I want the solution in two ways: Method 1 (without the Smith chart): Method 2 (using the Smith chart): A short circuit stub of length 0.04λ is used to match a 50 Ω lossless line to a load ZL = RL + j30 Ω. Use Smith chart to find:(a) The distance between the stub and the load.(b) The value of RL .arrow_forwardTHE FIRST PAGE OF THIS QUESTION SECTION BELOW IS THE FIRST IMAGE UPLOADED, WHICH SHOWS A digital synchronous sequential circuit and then comes the questions below:1B) Suppose the flip-flops are 74F74 devices and the AND gates are 74F08 devices. Let maxtpd,D=9ns, maxtsu,D=3ns, and maxtpd,AND=6ns. What is the maximum clock frequency at which the circuit can operate reliably? 2) Compare serial transmission and parallel transmission and discuss their advantages and disadvantages. 3) Explain briefly how the slave can protect itself from being overwhelmed by the master in I2 4) A hypothetical logic family has the following specifications. VOH=4.6V VIH=4.0V VOL=0.5V VIL=1.0V IOH=-1mA IIH=50μA IOL=8mA IIL=-0.6mA (4a) What are the noise margins? (4b) What is the fan-out capability?…arrow_forward
- THE FIRST PAGE OF THIS QUESTION SECTION BELOW IS THE FIRST IMAGE UPLOADED, WHICH SHOWS A digital synchronous sequential circuit and then comes the questions below:1B) Suppose the flip-flops are 74F74 devices and the AND gates are 74F08 devices. Let maxtpd,D=9ns, maxtsu,D=3ns, and maxtpd,AND=6ns. What is the maximum clock frequency at which the circuit can operate reliably? 2) Compare serial transmission and parallel transmission and discuss their advantages and disadvantages. 3) Explain briefly how the slave can protect itself from being overwhelmed by the master in I2 4) A hypothetical logic family has the following specifications. VOH=4.6V VIH=4.0V VOL=0.5V VIL=1.0V IOH=-1mA IIH=50μA IOL=8mA IIL=-0.6mA (4a) What are the noise margins? (4b) What is the fan-out capability?…arrow_forwardI need help on this question a) Find y(t) =yh(t) +yp(t) in time domainIs the system over-damped, under-damped, or critical?arrow_forwardGiven f(t)=a sin(ßt) a = 10 & ß = 23 Find the Laplace Transform using the definition F(s) = ∫f(t)e-stdtarrow_forward
- = Calculate Avf, Zif, and Zof for the amplifier circuit,Assume he = 50, hie 1.1k2, and identical transistors? 150kQ Vs 5002 HH +25v 10k +6 · 47ΚΩ 47k2 4.7k0} 33 ΚΩ 4.7ΚΩ 10k w 4.7kQ HH Voarrow_forwardFor the four-pole filter in Fig. (2), determine the capacitance values required to produce a critical frequency of 2680 Hz if all the resistors in the RC low-pass circuits are 1.8 K. Also select values for the feedback resistors to get a Butterworth response. Note: For a Butterworth response, the damping factor must be 1.848 for the first stage and 0.765 for the second stage. (2) Re Res ww " = 11arrow_forwardFor the circuit shown in Fig. 2.20, the transistors are identica' and have the following parameters: hje=50, hie = 1.1K, hr =0, and hoe = 0. Calculate Auf, Rif and Rof. Ans: 45.4; 112 KN; 129N. HH 150k 47k R 25 V 10k 47k 4.7k 5μF 33k 4.7k 50µF 50µF 4.7k 4.7k R₁ Roj R1000arrow_forward
- A triangular wave is applied to the input of Fig. (3). Determine what the output should be and sketch its waveform in relation to the input. 10μs. 0 5μs 15 μs 0.001 μF R₁ w 2.2karrow_forwardA three-phase, 480-V, 60-Hz, 6-pole, Y-connected induction motor has its speed controlled by slip power. The circuit parameters are given: Rs=0.06 ohms, Rr=0.05 ohms, Xs=0.2 ohms, Xr=0.3 ohms and Xm=6 ohms. The turn ratio of the rotor to stator winding is n=0.8. The no-load losses of the motor are equal to 150 W. The rotor and stator cupper losses are equal to 249.21 W. The slip power losses are estimated to 8000W. The load torque is 173.61 N.m. at 700 rpm. The efficiency is equal to: Select one: a. 71.5% b. None of these c. 81.5% d. 91.5% Question 2 Consider a 3-phase, 460-V, 100-hp, 0.88 power factor lagging, 4-pole, 1728 RPM, 60 Hz, Y-connected induction motor. The operating slip is equal to: Select one: a. 0.05 b. 0.01 c. 0.04 d. None of these Question 3 A 3 phase, 10 kW, 1750 rpm, Y- connected 460 V, 60 Hz, 4 poles, Y-connected induction motor has the following parameters: Rs = 0.5 Ohms, Rr = 0.3 Ohms, Xs = 0.9 Ohms, Xr = 0.9 Ohms, Xm = 25 Ohms. The no load…arrow_forwardelectric plants do for hand writingarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSONDelmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage LearningProgrammable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
- Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill EducationElectric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSONEngineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,

Introductory Circuit Analysis (13th Edition)
Electrical Engineering
ISBN:9780133923605
Author:Robert L. Boylestad
Publisher:PEARSON

Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:9781337900348
Author:Stephen L. Herman
Publisher:Cengage Learning

Programmable Logic Controllers
Electrical Engineering
ISBN:9780073373843
Author:Frank D. Petruzella
Publisher:McGraw-Hill Education

Fundamentals of Electric Circuits
Electrical Engineering
ISBN:9780078028229
Author:Charles K Alexander, Matthew Sadiku
Publisher:McGraw-Hill Education

Electric Circuits. (11th Edition)
Electrical Engineering
ISBN:9780134746968
Author:James W. Nilsson, Susan Riedel
Publisher:PEARSON

Engineering Electromagnetics
Electrical Engineering
ISBN:9780078028151
Author:Hayt, William H. (william Hart), Jr, BUCK, John A.
Publisher:Mcgraw-hill Education,