Please, I want the solution in two ways: Method 1 (without the Smith chart): Method 2 (using the Smith chart): A short circuit stub of length 0.04λ is used to match a 50 Ω lossless line to a load ZL = RL + j30 Ω. Use Smith chart to find:(a) The distance between the stub and the load.(b) The value of RL .

Please, I want the solution in two ways: Method 1 (without the Smith chart): Method 2 (using the Smith chart): A short circuit stub of length 0.04λ is used to match a 50 Ω lossless line to a load ZL = RL + j30 Ω. Use Smith chart to find:(a) The distance between the stub and the load.(b) The value of RL .

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.17MCQ

See similar textbooks

Similar questions

4. Two antennas, each of input imdedance Z=73+j0 Q, are fed with lossless lines from a generator. The length of all the lines is 3/8, as shown in the following figure. Determine the input resistance Zin. 31/8 lin 3002 73Ω ww Zc=1502 100 Z0° Ze=3002 31/8 Zc=150 73Ω Zin 3/8
what is expected VSWR for a transmission line with a reflection coefficient of 0.377
The lossless line shown in figure below is operating with å =100 cm. If d = 10 cm, d = 25 cm, and the line is matched to the left of the stub, what is Z, ? Z-3000 Z-3000
I need the answer quickly
Three lossless lines are connected as shown in the figure below. Determine the input impedance. a/2 2/4 3A/4 Z,,= 500 Z= 1000 Zg= 750 Z= 60-j40 Q "03
A coaxial cable is 10 meters long, and is filled with lossless Teflon, having a relative permittivity of 2.1. There is a matched load at the end of the line (this means that there is no reflection at the end, so there is only a signal traveling in the + z direction). At the input of the line, a sawtooth waveform is applied, having a peak voltage of 1.0 [V] and a duration of 1.0 [ns] (the time from the beginning of the waveform until the end). Make a plot (versus time) of what an oscilloscope would read if it were connected to the line at various locations, corresponding to the following values of z: 0.0 [m], 1.0 [m], 5 [m], 10 [m]. Plot out to 50 [ns] 1
5
10 V In the lossless transmission line system shown, the switch S is closed at t = 0. a. Find the reflection coefficient IJ. b. Find the reflection coefficient TL. c. Find the transmission coefficient t+. d. Complete the following reflection diagram in order to determine the total voltages VA, VB, Vc, and VD. 752 201=7522 T VA= 5 em |V₁ = ? |V₂ = ? Figure P6 70₂= Son T V₂=? 4 [V=0] Vc 15022
Name t=0 502 8012 502 COAXIAL CABLE 5000 m A swikh closing at t=0 sends a voltage daun a s000m transmission line with a velocity facter of .8 Calculate : a) The magnitue of the incident voltage traveling to Hhe load. 6) The rellecion coeficient c) The magnikle of the refleckd voltage d) The voltage on the line after all reflections have ceased. e) The time for all reflectias to cease
A 50 transmission line is to be connected to a 72 load through a 1/4 quarter wave matching transformer. (a) What must be the characteristic impedance of the transmission line that is used to form the quarter wave transformer? (b) If the frequency of operation is 7 MHz and the phase velocity through the quarter wave section is 2c/3, what is the length of the quarter wave section? You may assume the transmission line forming the quarter wave section is lossless.
5. Two cascaded lossless transmission lines are terminated by Z₁-2502, as shown below.. a) Calculate the reflection coefficient and the standing wave ratio at the load, i.e., the CC' terminal. b) Determine the characteristic impedance of the quarter-wavelength transformer, Zol, to match the cascaded line to a 6492 generator. B A- A'. Zol 11= 2/4 B' Zo2=75 92 12=32/4 C C ZL=2592
Subject:communication Need answer