A 50 transmission line is to be connected to a 72 load through a 1/4 quarter wave matchingtransformer. (a) What must be the characteristic impedance of the transmission line that isused to form the quarter wave transformer? (b) If the frequency of operation is 7 MHz and thephase velocity through the quarter wave section is 2c/3, what is the length of the quarter wavesection? You may assume the transmission line forming the quarter wave section is lossless.

Step 1: Step 2: Step 3: Step 4:

Answered: A 50 transmission line is to be…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.21MCQ

See similar textbooks

Similar questions

We shall study the function of the PN generator in the context of the transmitter (Tx) and receiver (Rx) circuits by means of a simple example.
b) A periodic composite signal with a bandwidth of 2500 Hz is composed of two sine waves. The first one has a frequency of 100 Hz with maximum amplitude of 20 volts; the second one has maximum amplitude of 5 volts. What is the frequency for the second sine waves? Draw the frequency spectrum.
Need Help with parts 11 and 12 please. Thank you
*2. If a 1500-kHz radio wave is modulated by a 2-kHz sine-wave tone, what frequencies are con- tained in the modulated wave (the actual AM signal)?
4.) A transformer has a primary coil with 300 windings, and secondary coil has 400 windings. The input AC power supply is 120 volts (Vrms). A) Is this a step-up or step-down transformer? B) What is the rms voltage across the output terminals (Vrms)? C) What is the peak voltage across the output terminals (Vmax)? Primary Secondary imm ac input
Why is the negative effect of stray capacitance more pronounced in very high frequency circuits?
A sine wave carrier is modulated by a single tone so that Emax = 25 mV and Emin = 10 mV. Calculate the modulation index. a.0.67 b.0.29 c. 0.43 d.0.60
Imagine a two-dimensional system in which a sinusoidal waveform is excited at the exact center of a circular plate. The standing wave pattern is established when the excited wave two-dimensionalwaveforms for a stable equilibrium pattern of constructive and destructive interference with the reflected waves from the edge of the circular plate. Draw what you expect the standing wave patterns to look like in this two-dimensional system for increasing resonant harmonics, n. Explain what characteristics of the oscillating plate affect the value of those resonancefrequencies, and what geometric properties of the plate affect the patterns.
The step down DC chopper uses DC source voltage V(dc) = 200 V and resistive load impedance of 10 ohm. The duty cycle is 0.4 the voltage drop across the switch may be taken as zero, Calculate : (a) Average and RMS value of output voltage. (b) Average and RMS value of output current.
5. What is the wavelength in ft of a 60 Hz ac signal?
Answer is 2.93 hz. Take No. Of poles = 2.
An FM signal has a frequency deviation of 8 kHz and a modulating frequency of 1.2 kHz. The signal-to-noise ratio at the input to the receiver detector is 19.4 dB. Calculate the approximate signal-to-noise ratio (in dB) at the detector output. A sine wave of frequency 7 kHz phase modulates a carrier at 22 MHz. The peak phase deviation is 1 rad. Calculate the maximum frequency deviation in Hz. A phase modulation system operates with a modulation index of 2. What is the maximum phase shift in degrees?

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning