"I need proof in the solution and a supportedsource with the solution.'Choose the correct answer for the following sentencesd. 32.. The 8086 microprocessor has --------- data pin'sa. 8 b. 16 c. 202. The 8086 microprocessor hasa. 16 b. 8 c. 32 d. 203. SP &address pin'sused with stack segment register (SS) to access memory within the stack segmenta. BP b. IP c. SI d. DI4. If CS 002AH and IP- 0023H, the physical address is -----a. 002C3H b. 0023H1 c. 002A1H d. 0023H5. POP instruction used tothe stacka. Read b. Write c. Reset d. Set6. PIC16F877A microcontroller has ------ digital I/O portsa. 2 b.4 c. 5 d. 87. PIC16F877A microcontroller has analog multiplexed portsb. 2 b. 4 c. 5 d. 88. used to control the brightness of LED connected to Arduinoa. Analog input b. analog output c. digital input d. digital output9. The content of SP when execute PUSH instructiona. Increased by 2 b. decreased by 2 c. multiplied by 2 d. divided by 210. If CS-002B & IP-0013, physical address is -----a. 002C3 b. 002CC c. 0022Cd. 00CC2

Here is a detailed explanation for each answer:1. The 8086 microprocessor has __ data pins.Answer:…

Answered: "I need proof in the solution and a…

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

I need expert assistance in solving the choices, providing evidence not through explanations but through images or by illustrating with a diagram of the EMU8086 processor. -1. The Intel 8086 microprocessor can read/write 16 bit data from or to a. I/O device b. register (C, memory d. processor 2. Which unit in the 8086 microprocessor is responsible for pre-fetching instructions from memory? a. EU b. ALU c. BIU 3. The memory of 1M byte size could be divided into a. twenty-one b. thirty-four d. CU Kbyte segments. d. sixty-four c. thirty-three 4. Which of the following programming statements is NOT a valid comparison operator in Arduino? != (not equal to) b. < (less than) c. and (logical AND) d. = (equal to) 5. How many A/D converter inputs pins does port-E in the PIC16F877A? b. 6-Pins c. 4-Pins a. 3-Pins 6. How much the size of the program memory space in the b. 16Kx16 bits c. 8Kx14 bits a. 32Kx8 bits 8-Pins PIC16F877A microcontroller? d. 4Kx14 bits
Include circuit diagram
Q1. (a) Design a stick (layout) diagram for the following static CMOS logic gate, where A, B, C, D are the logic gate inputs and O/P is the output: VDD D-d[Q8 A-Q5 B-Q6 c-d[Q7 O/P CQ3 DQ4 B-Q2 A-Q1 Vss Figure 1 Use dual-well, CMOS technology. Include wells, well-taps, contact cuts, routing of power and GND in your diagram. Use colour coding and/or clear and readable detailed annotations to represent the wires in the different layers.
Q1. (a) Design a stick (layout) diagram for the following static CMOS logic gate, where A, B, C, D are the logic gate inputs and O/P is the output: VDD D-d[Q8 A-Q5 B-Q6 C-d [Q7 O/P CQ3 DQ4 B-Q2 AQ1 Vss Figure 1 Use dual-well, CMOS technology. Include wells, well-taps, contact cuts, routing of power and GND in your diagram. Use colour coding and/or clear and readable detailed annotations to represent the wires in the different layers. (b) The logic gate from (a) needs to drive a capacitive load of 150 fF with a rise-time and fall-time of 1.2 ns. If the length of all transistors is 0.5 μm, calculate the required widths for all P-type and all N-type MOSFETs in the logic gate to achieve the required edge-speeds. Clearly show the calculation steps of your solution. Assume VDD = 5 V, K'n = 50 μA/V², K'p = 20 μA/V²
Q3/(A) False OR True 1- A0-0 and BHE-1 are used as low bank-select signal: 2-AX is 2234 H after executing the following instruction: AAS. If AX-2234H. 3-IP register holds the offset address of the next instruction to be executed. 4- The XLAT instruction in 8086 assembly language is used to perform arithmetic operations between two memory operands. 5- Bus interface unit is responsible form
Can you give me a simple example of each mistake in the Emu8086 program? Registers should be of the same size. One way to reduce memory usage is to use AX or AL. Explain.
q24- The logic gate that will have HIGH or “1” at its output when any one of its inputs is HIGH is a/an …………… gate. a. AND Gate b. OR Gate c. NAND Gate d. NOT Gate Clear my choice
not use ai please don't
Please may you give the solution to this computer science question! Thank you
By using the information given in image below design a BCD Counter. You have to provide all the necessary information needed to design this circuit.
I need the solution, expert, to be correct with clarification. a. Write an 8086-microprocessor program to perform the result of the logical expression: BP (X₁ X2) + (X₁. X2), where X₁-01FFH, X2=AD58H: b. There are 30 data bytes are stored in memory location with offset address 3100H to 311EH. Write 8086 microprocessor program to transfer the block of data to new location with offset address 4201H to 421F
Solve in 8086 microprocessor

SEE MORE QUESTIONS

Recommended textbooks for you

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

SEE MORE TEXTBOOKS