Problem 1Design a full wave rectifier to supply a 20 V DC load that draws an average current of 300 mA. If we want tokeep the ripple to less than 3%, determineWhat is the minimum value of the smoothing capacitor? (5 points)What should be the peak value of my 60 Hz AC source? (5 points)

Answered: Image /qna-images/answer/65117444-2042-45d5-9983-f0d047942b66.jpg

Answered: Problem 1 Design a full wave rectifier…

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Question

Problem 1
Design a full wave rectifier to supply a 20 V DC load that draws an average current of 300 mA. If we want to
keep the ripple to less than 3%, determine
What is the minimum value of the smoothing capacitor? (5 points)
What should be the peak value of my 60 Hz AC source? (5 points)

Expert Solution

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

What is the difference between a diode and rectifier?
A three phase full wave rectifier is shown below along with peak phase voltage Vm-169.7V. The load is purely resistive. The rectifier delivers Ipc = 100 A and the source frequency is 60 Hz. The DC output voltage is %3D VDc=280.7V and the output RMS voltage is equal to VRMS=280.93V. The efficiency, FF and RF are respectively equal to: Secondary D D D, R AD. Z D. D, Select one: O a. 99.83%, 100.08%, 4% O b. 99.83%, 55.08%, 4% O C. 99.83%, 100.08%, 16% O d. 87.83%, 100.08%, 4%
A sine wave has a maximum value of 440 V. (a) What is its RMS or "effective" value? (b) What is the average value (assume full-wave rectifier)? (c) At what angle of rotation will the voltage reach a value of 120 V?
For the full wave rectifier circuit shown in Figure 1, calculate: 1) The maximum current through the load. 2) The average current through the load. 3) The average voltage across the load. 4) The rms value of the current. 5) The rectification efficiency. Vms = 280V Vin RL= 12ks2 Vrms = 280V Figure 1
A full-wave rectifier uses 2 diodes. The internal resistance of each diode is 20 02. The transformer RMS secondary voltage from centre tap to each end of the secondary is 50 V and the load resistance is 980 2. Mean load current will be
Question (2) A controlled half-wave rectifier has a 240 V rms 60Hz ac source, The load a is R=30 Ohm resistor (a) Determine the delay angle such that the average load current is 2.5A (b) Determine the power absorbed by the load (c) Determine the power factor.
In the circuit of the following figure, the input voltage Vs is 15 volts rms with a frequency of 60 Hz, R equals 150 Ohms and C equals 100,000 Pico Farads. The diodes are Germanium (Vd = 0.2 volts) and the Zener diode is 12 volts. a) The magnitude of the ripple voltage at Cb) The Magnitude of the Peak Inverse Voltage (PIV) for D1 and D2.
In a full wave bridge rectifier, the input sine wave is 40sin100πt. What will be the average output voltage and ripple frequency?
Consider the full- wave bridge rectifier circuit. The input signal is 120 V (rms) at 60 Hz. The load resistance is R250. The peak output voltage is to be 9 V and the ripple voltage is to be no more than 5 percent. Determine the required turns ratio and the load current. Note please solve within 30 minutes.avoid plagiarism
Please respond to two part question in attached image. Please.
A 60 Hz sinusoidal voltage with an RMS value of 120 V is applied to a single-phase full-wave SCR rectifier. The DC output voltage of the rectifier is 101 V, the firing angle (in degrees) of SCR is would be: O A. 36 O B. 45 O C. None of the other choices are correct O D. 30 O E. 60
A certain unfiltered center-tapped full wave rectifier is powered by a 120 Vrms, 60 Hz power system. The peak value of the output voltage under loaded conditions is 30 V. The capacitance value is 2000 uF, load current of 2A, determine the following: Peak to peak ripple voltage RMŞ ripple voltage 4. а.

SEE MORE QUESTIONS

Recommended textbooks for you

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning