Need a solu 5.7 Design an STS switch for 128 primary TDM signals of the CCITT hierarchy (30voice channels per input). Blocking should be less than 0.002 and the loading is0.2 erlang per channel. How many time slot interchange modules are needed?What is the complexity of the switch?Repeat Problem 5.7 for a TST design.

May this answer helpful to you.

Answered: 5.7 Design an STS switch for 128…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

ChapterS: Safety, Basic Electricity And Ohm's Law

Section: Chapter Questions

Problem 8RQ: What is an MSDS?

See similar textbooks

Similar questions

In MOSFET devices the N-channel type is better than the P - Channel type in the following respects. (a) It has higher power density (b) It is faster (c) It is TTL compatible (d) It has larger carrier effective mass Explain your answer.
03)b) For Noiseless AWGN channel, show that : maximum channel capacity Cmax = 1.44 2 bps?
Explain the QPSK modulation challenges and problems.
Q4. Consider the QPSK digital modulation scheme (a) What does the abbreviation QPSK stand for? (b) Sketch an I-Q constellation diagram for this modulation scheme. (c) State the number of bits per symbol. (d) If the bit rate that is achieved with this modulation scheme is 128 Mbit s-, what is the baud (symbol) rate?
3. a) What does TDMA stand for? What does it mean? Explain or sketch the concept. b) What is PAM? What does it stand for? Explain or sketch how the modulated signal looks like.
4) Describe cell phone standards and systems such as FDMA(AMPS/TACS), TDMA (GSM/IS-54) and CDMA (IS-95).
2. (a), What is the bäsic. limitation of SSB scheme?. How climinated by VSB modulation? is it modulation b) Draw the block diagram of super heterodyne AM réceiver and explain the function of IF amplifier.
c) Draw a block diagram of a typical digital communications system including both transmit and receive paths and describe the nature of the signals generated by each of the blocks. Briefly describe what happens within the Modulator element and explain what is meant by the term 'up-conversion'.
a) What is the advantage of increasing the switching frequency in switching converters (Buck, Boost etc.)and causes disadvantages to arise? b) General characteristics of IGBT and MOSFET, such as the current, voltage and switching frequency they can be producedCompare in terms of values. c) Output current and voltage ripples for a Buck-Boost type power converterWhat variables do (ripples) depend on? Explain.
It's urgent please solve asap.
1- Consider a PCM system for a sinusoidal signal 2 cos2л 2000t. It is desired to represent this signal such that the signal to quantization noise ratio is 20 dB. Determine: (a) Sampling frequency required. (b) The quantizing step size. (c) The number of bits per word (per sample). (d) Bit rate and bit duration. (e) The channel bandwidth needed.
In the clock divider HDL code shown in section 5.8, what should the value for half be in order to generate: a. A 4 Hz output clock from the 50 MHz input clock source? b. A 1 MHz output clock from 50 MHz input clock source?

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS