Concept explainers
(a)
The number of non reference nodes.
Answer to Problem 3.35HP
The number of non reference nodes is
Explanation of Solution
Calculation:
The given diagram is shown in Figure 1
The non reference node is anode that is connected between a voltage node and any other element of the circuit.
From the above figure it is clear that there are in total
Conclusion:
Therefore, the number of non-reference nodes is
(b)
The number of unknown node voltage.
Answer to Problem 3.35HP
The number of unknown node voltages is
Explanation of Solution
Calculation:
From the figure shown in Figure 1, the number of unknown node voltages are
Conclusion:
Therefore, the number of unknown node voltages is
(c)
The value of
Answer to Problem 3.35HP
The value of voltage
Explanation of Solution
Calculation:
Mark the values and redraw the circuit.
The required diagram is shown in Figure 2
Apply nodal at
The expression for the voltage across the resistance
Substitute
The expression to calculate the voltage
Substitute
The voltage across the resistance
Substitute
The expression for the voltage
Substitute
The voltage across the resistance
Substitute
The expression to calculate the voltage
Substitute
Conclusion:
Therefore, the value of voltage
Want to see more full solutions like this?
Chapter 3 Solutions
Principles and Applications of Electrical Engineering
- Show handwriting solutions not Aiarrow_forwardMaul Dulde Questio119 819 PREV NEXT In the lab, you have setup a thermocouple and have used a thermistor along with an ice bath and water at various temperatures (confirmed with the thermistor) up to 100 degrees Celsius for calibration. The calibration data is shown in the table below and the full-scale output range is 0-5 mV. You note that there is scatter in your data; however, you must use a linear curve fit to efficiently process the measurements during an automated temperature measurement process. Question 1 100% Question 2 100% Question 3 100% Question 4 100% Question 5 100% Question 6 100% mV The slope of your linear calibration curve for the thermocouple is 0.0334 °C with an offset of -0.07 mV. Question 7 100% Question 8 100% What is the maximum expected linearity error as a percentage of the full-scale output? Question 9 0% Summary -0.08 Thermocouple Calibration Data Temperature (°C) Voltage (in mV) 0 20 20 40 40 60 60 60 80 96 90 0.587 1.314 1.901 2.528 2.782 100 3.055 LIT…arrow_forwardOnly expert should solve itarrow_forward
- What is the high cutoff frequency? What is the low cutoff frequency? What is the bandwidth?arrow_forwardNeed handwritten pen and paper solution do not use chatgpt or AI otherwise downvote. An AC motor with impedance Z₁ = 4.2 + j3.6 ohm is supplied from a source of 220 V at 60 Hz. Find: a) pf, P and Q, b) Determine the capacitor required to connect in parallel with the motor so that the power factor is corrected and equal to 0.98 behind.arrow_forwardNeed handwritten pen and paper solution do not use chatgpt or AI otherwise downvote An AC motor with impedance Z₁ = 4.2 + j3.6 ohm is supplied from a source of 220 V at 60 Hz. Find: a) pf, P and Q, b) Determine the capacitor required to connect in parallel with the motor so that the power factor is corrected and equal to 0.98 behind.arrow_forward
- Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSONDelmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage LearningProgrammable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
- Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill EducationElectric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSONEngineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,