Fundamentals of Heat and Mass Transfer
7th Edition
ISBN: 9780470917855
Author: Bergman, Theodore L./
Publisher: John Wiley & Sons Inc
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 10, Problem 10.74P
a.
To determine
To find: The chip temperature and power dissipation.
b.
To determine
To find: Tube length required to maintain the required condition.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Analyze the condensation process using both chillers. Provide operating temperatures and pressures entering each component shown in the diagram (at points 1, 2, 3, 4). Indicate which chiller should be chosen based on the economics. See below for details:
-Your work is replacing a chiller that is used as part of a distillation process that condenses methanol (boiling point = 65 °C). Your task is to select the most economical type of system. A conventional chiller will have a lower first cost and will have lower maintenance costs than one that involves enhanced heat transfer surfaces, but the chiller with enhanced surfaces will condense the same amount of alcohol with a lower energy consumption. Select the appropriate chiller by considering the net present value of both systems. That value will involve the first cost of the chiller, and the present value of the maintenance and energy costs. The chiller uses a standard vapor-compression refrigeration cycle with R-22 (see Figure 1). For…
1. Water at atmospheric pressure is to be boiled in polished copper pan. The diameter of the pan is 300
mm and is kept at 111°C. Calculate the following :
() Power of the burner to maintain boiling;
(i) Rate of evaporation in kg/h.
Take the properties of water at 100°C as follows:
P, = 958 kg/m"; p, = 0.597 kg/m²; µ,= 278 × 10ʻ kg/ms; c= 4216 JkgK;
= 2257 kJ/kg ; Pr= 1.723, o = 58.9 x 10-³ N/m
%3D
[Ans. (1) 13.664 kW, (i) 21.8 kg/h]
need soon all parts
don't copy I will downvote
Chapter 10 Solutions
Fundamentals of Heat and Mass Transfer
Ch. 10 - Show that, for water at 1-atm pressure with...Ch. 10 - The surface of a horizontal. 7-mm-diameter...Ch. 10 - The role of surface tension in bubble formation...Ch. 10 - Estimate the heat transfer coefficient, h,...Ch. 10 - Prob. 10.5PCh. 10 - Prob. 10.6PCh. 10 - Prob. 10.7PCh. 10 - Prob. 10.8PCh. 10 - Calculate the critical heat flux on a large...Ch. 10 - Prob. 10.11P
Ch. 10 - Prob. 10.12PCh. 10 - Prob. 10.13PCh. 10 - Prob. 10.15PCh. 10 - Prob. 10.16PCh. 10 - Consider a gas-fired boiler in which five coiled,...Ch. 10 - Prob. 10.18PCh. 10 - Prob. 10.19PCh. 10 - Prob. 10.20PCh. 10 - Prob. 10.22PCh. 10 - Prob. 10.24PCh. 10 - Prob. 10.25PCh. 10 - A small copper sphere, initially at a uniform,...Ch. 10 - Prob. 10.28PCh. 10 - A disk-shaped turbine rotor is heat-treated by...Ch. 10 - A steel bar, 20 mm in diameter and 200 mm long,...Ch. 10 - Electrical current passes through a horizontal....Ch. 10 - Consider a horizontal. D=1 -mm-diameter platinum...Ch. 10 - Prob. 10.34PCh. 10 - Prob. 10.35PCh. 10 - Prob. 10.36PCh. 10 - Prob. 10.37PCh. 10 - A polished copper sphere of 10-mm diameter,...Ch. 10 - Prob. 10.39PCh. 10 - Prob. 10.40PCh. 10 - Consider refrigerant R-134a flowing in a smooth,...Ch. 10 - Determine the tube diameter associated with p=1...Ch. 10 - Saturated steam at 0.1 bar condenses with a...Ch. 10 - Prob. 10.45PCh. 10 - Prob. 10.46PCh. 10 - Prob. 10.47PCh. 10 - Prob. 10.48PCh. 10 - Prob. 10.50PCh. 10 - Prob. 10.53PCh. 10 - The condenser of a steam power plant consists of...Ch. 10 - Prob. 10.56PCh. 10 - Prob. 10.61PCh. 10 - Prob. 10.62PCh. 10 - A technique for cooling a multichip module...Ch. 10 - Determine the rate of condensation on a 100-mm...Ch. 10 - Prob. 10.66PCh. 10 - Prob. 10.67PCh. 10 - Prob. 10.70PCh. 10 - Prob. 10.71PCh. 10 - Prob. 10.74PCh. 10 - Prob. 10.75PCh. 10 - A thin-walled cylindrical container of diameter D...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Carbon dioxide (CO:) is used for the gas cooled reactor in shell and tube heat exchanger type steam generator (shown in Figure 2). 90000 kg/h entered to the exchanger under pressure and temperature of 4 bar and 500 °C respectively. The steam saturation temperature is 250 °C when the carbon dioxide leave the generator at 330°C. Presume the formed steam is saturated and dry. Using 25 mm inner diameter and 2 mm wall thickness, a copper tube is designed for CO; mass flow rate of 350000 kg/m'h. Neglect the thermal resistance of the steam side. (a) Determine number of tubes that should be used (b) Determine the length of the tubes Take the following properties for the carbon dioxide: Cp=1.172 KI/kg °C; u=0.0000298 Ns/m²; k=0.043 w/m °C; p=3.26 kg/m² Take k (Copper) = 384 W/m °C Water in (cold fluid) - 250°C CO, (hot fluid) in (f = 500°C) CO, out (2 - 330°C) Steam out (2 250°C)arrow_forwardAH of vaporization of water is 439.2 cal/g at the normal boing point. Since virus can survive at 404.39 K by forming spores. Most virus spores die at 851.9 K. Hence, autoclaves used to sterilize medical and laboratory instruments are pressurized to raise the boiling point of water to 851.9 K. Find out at what InP (torr) does water boil at 851.9 K? O a. 8460.435 O b. 940.048 c. 1880.097 O d. 2.474arrow_forwardWater is to be boiled at atmospheric pressure in a polished copper pan placed on top of a heating unit. The diameter of the bottom of the pan is 00.2 m. If during 30 minutes the water level is dropped by 0.1 m, calculate the inner surface of the bottom of the pan. Assumptions 1 Steady operating conditions exist. 2 Heat losses from the heater and the pan are negligible 3 The boiling regime is nucleate boiling. Note. Write your answer step by step and clearly explain your work. You need to upload a file.arrow_forward
- A 5.00-ml. sample of blood was treated with trichloroacetic acid to precipitate proteins. Alter centrifugation, the resulting solution was brought to a pH of 3 and was cxtraccd with two 5-mL portions of methyl isobutyl ketone containing the organic lead complexing agent APCD. The extract was aspirated directly into an air-acetylene flame yielding an absorbance of 0.454 at 283.3 nm. Five-milliliter aliquots of standard solutions containing 0.240 and 0.475 ppm Pb were treated in the same way and yielded absorbancc of 0.412 and 0.642. Calculate the concentration Pb (ppm) in the sample assuming that Beer's law is followed.arrow_forward24 Hexane C,H is used for fuel in a CI engine at an air-fuel ratio AF = 25. Hexane has a specific gravity of 0.659 and a midpoint boiling temperature of 69 C. Calculate: (a) Equivalence ratio. (b) Lambda value. (c) Cetane index of hexane.arrow_forwardkindly help me with this problem Enumerate and explain each briefly the FOUR (4) Properties of the Bernoulli Processarrow_forward
- can you answer the questionarrow_forwardSaturated, pure steam at a temperature of 170 oC condenses on the outer surface of a vertical tube of outer diameter 2 cm and length 1.5 m. The tube surface is maintained at a uniform temperature of 150 oC. Calculate: the local film condensation heat-transfer coefficient at the bottom of the tube. the average condensation heat-transfer coefficient over the entire length of the tube. the total condensation rate at the tube surface.arrow_forwarda) the local film condensation heat-transfer coefficient at the bottom of the tube b) the average condensation heat-transfer coefficient over the entire length of the tube c) the total condensation rate at the tube surface.arrow_forward
- An ice plant produces 20 tons of ice per day at -15oC from water at 25 oC. Ifmiscellaneous losses are 12 % of the freezing and chilling load, calculate therefrigeration capacity of the plant, in TR.arrow_forward2. Find: a. hof steam at saturation pressure of 0.015 MPa and temperature of 800 K b. v of subcooled liquid at saturation pressure of 1.44 MPa and temperature of 17.5°C Use the sample table as reference for your solution in number 2 Sample, find the enthalpy of superheated steam at 1.45 MPa and 515°C. Option 1. Identify the value of the blue ones for the first 2 interpolations. Option 2. Identify the value of the green ones for the first 2 interpolations. 1.4 hs00°C,1.4MP h515°C1.4MPa. H520°C.1.4MPa. Saturation Pressure (MPa) 1.45 h500°C.1.45MP h515°C,1,45MP h520°C.1.45MPa. 1.5 hs00°C,1.5MP H515°C,1. 5MPa h520°C.1.5MPa 500 Temperature °C 515 520arrow_forwardQuestion 3 Which statement about vaporization enthalpy and condensation enthalpy is correct? O The condensation enthalpy is equal in magnitude but opposite in sign when compared to the vaporization enthalpy O There is no general relationship between these two quantities and the values depend on the substance involved. O The vaporization enthalpy is always less than the condensation enthalpy. O The vaporization enthalpy is exactly equal to the condensation enthalpy.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Extent of Reaction; Author: LearnChemE;https://www.youtube.com/watch?v=__stMf3OLP4;License: Standard Youtube License