Fundamentals of Heat and Mass Transfer
7th Edition
ISBN: 9780470917855
Author: Bergman, Theodore L./
Publisher: John Wiley & Sons Inc
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 10, Problem 10.15P
To determine
The heat power requirement.
The rate of evaporation.
The ratio of power requirement and critical heat flux.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
In boiling water at 1 atm pressure outside a stainless-steel tube with a surface temperature of 410F, the heat-transfer coefficient h in the absence of radiation is 32 Btu/h*ft^2*F. If the emissivity of the stainless steel is 0.8, will radiation significantly augment the rate of boiling (e.g., by more than 5 percent)? Assume that the vapor film is transparent to radiation and the boiling liquid is opaque.
Saturated, pure steam at a temperature of 170 oC condenses on the outer surface of a vertical tube of outer diameter 2 cm and length 1.5 m. The tube surface is maintained at a uniform temperature of 150 oC.
Calculate:
the local film condensation heat-transfer coefficient at the bottom of the tube.
the average condensation heat-transfer coefficient over the entire length of the tube.
the total condensation rate at the tube surface.
Estimate the interfacial heat transfer coefficient for evaporation of a thin film of
saturated liquid water at atmospheric pressure. The liquid film rests on a flat, solid
surface to which a constant and uniform heat flux of 150 kW/m? is applied. The
accommodation coefficient may be taken to be 0.05. If the liquid film thickness is 0.2
mm, compare the interfacial vaporization resistance with the conduction resistance
through the liquid film.
Chapter 10 Solutions
Fundamentals of Heat and Mass Transfer
Ch. 10 - Show that, for water at 1-atm pressure with...Ch. 10 - The surface of a horizontal. 7-mm-diameter...Ch. 10 - The role of surface tension in bubble formation...Ch. 10 - Estimate the heat transfer coefficient, h,...Ch. 10 - Prob. 10.5PCh. 10 - Prob. 10.6PCh. 10 - Prob. 10.7PCh. 10 - Prob. 10.8PCh. 10 - Calculate the critical heat flux on a large...Ch. 10 - Prob. 10.11P
Ch. 10 - Prob. 10.12PCh. 10 - Prob. 10.13PCh. 10 - Prob. 10.15PCh. 10 - Prob. 10.16PCh. 10 - Consider a gas-fired boiler in which five coiled,...Ch. 10 - Prob. 10.18PCh. 10 - Prob. 10.19PCh. 10 - Prob. 10.20PCh. 10 - Prob. 10.22PCh. 10 - Prob. 10.24PCh. 10 - Prob. 10.25PCh. 10 - A small copper sphere, initially at a uniform,...Ch. 10 - Prob. 10.28PCh. 10 - A disk-shaped turbine rotor is heat-treated by...Ch. 10 - A steel bar, 20 mm in diameter and 200 mm long,...Ch. 10 - Electrical current passes through a horizontal....Ch. 10 - Consider a horizontal. D=1 -mm-diameter platinum...Ch. 10 - Prob. 10.34PCh. 10 - Prob. 10.35PCh. 10 - Prob. 10.36PCh. 10 - Prob. 10.37PCh. 10 - A polished copper sphere of 10-mm diameter,...Ch. 10 - Prob. 10.39PCh. 10 - Prob. 10.40PCh. 10 - Consider refrigerant R-134a flowing in a smooth,...Ch. 10 - Determine the tube diameter associated with p=1...Ch. 10 - Saturated steam at 0.1 bar condenses with a...Ch. 10 - Prob. 10.45PCh. 10 - Prob. 10.46PCh. 10 - Prob. 10.47PCh. 10 - Prob. 10.48PCh. 10 - Prob. 10.50PCh. 10 - Prob. 10.53PCh. 10 - The condenser of a steam power plant consists of...Ch. 10 - Prob. 10.56PCh. 10 - Prob. 10.61PCh. 10 - Prob. 10.62PCh. 10 - A technique for cooling a multichip module...Ch. 10 - Determine the rate of condensation on a 100-mm...Ch. 10 - Prob. 10.66PCh. 10 - Prob. 10.67PCh. 10 - Prob. 10.70PCh. 10 - Prob. 10.71PCh. 10 - Prob. 10.74PCh. 10 - Prob. 10.75PCh. 10 - A thin-walled cylindrical container of diameter D...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- need soon all parts don't copy I will downvotearrow_forwardcan you answer the questionarrow_forwardWater at atmospheric pressure is boiled in a container using a horizontal 8 mm electric wire (ε=0.9) whose temperature is maintained by an electric current at 250oC. Estimate the boiling heat transfer coefficient between the water and the wire surface. Properties of Water, liquid: ρl = 957.9 kg/m3, hfg = 2257 kJ/kg, vapor: ρv = 4.8 kg/m3, Cp,v = 2560 J/kg.K, μv = 14.85*10-6 N.s/m2, kv=0.0331 W/mK. Select one: a. 247 W/m2K b. 440 W/m2K c. 90.7 W/m2K d. 710 W/m2Karrow_forward
- A horizontal pipe of 125-mm-diamter and 1 m long with a surface temperature of 95 ℃ is used to condense saturated steam at 1 atm. Determine the heat transfer rate for the condensation process. Properties of Water, vapor (1 atm): Tsat = 100℃, ρv = 0.596 kg/m3, hfg = 2257 kJ/kg; Water, liquid (Tf = 370K): ρl = 960.6 kg/m3, Cpl = 4214 J/kg.K, μl = 289*10^-6 N.s/m2, kl = 0.679 W/m.K.arrow_forwardA horizontal pipe of 100-mm-diamter and 1 m long with a surface temperature of 94 ℃ is used to condense saturated steam at 1 atm. Determine the heat transfer rate for the condensation process. Properties of Water, vapor (1 atm): Tsat = 100℃, ρv = 0.596 kg/m3, hfg = 2257 kJ/kg;Water, liquid (Tf = 370K): ρl = 960.6 kg/m3, Cpl = 4214 J/kg.K, μl = 289*10^-6 N.s/m2, kl = 0.679 W/m.K. Select one: a. 28567 W b. 18254 W c. 19076 W d. 22552 Warrow_forwardlarge dry air is flowing over a surface from which benzene is evaporating with 1 atm absolute pressure as total pressure. The partial pressure of benzene at the surface is the vapor pressure at 298 K which is (0.42 atm). The Ke has been estimated to be (6.5*10s kmol / s.m'. mol vol.). Calculate the vaporizing rate benzene, and the individual mass transfer coefficient Ky? (R=0.000082)arrow_forward
- An open tank, 6 mm in diameter, contains 1 mm deep layer of benzene (Mol wt = 78) at its bottom. The vapour pressure of benzene in the tank is 13.15 kN/m2 and its diffusion takes place through a stagnant air film 2.5 mm thick, At the operating temperature of 20°C, the diffusivity of benzene in the tank is 8.0 x 10-6 m2/s. If the benzene has a density of 880 kg/m³, calculate the time taken for the entire benzene to evaporate. Take atmospheric pressure as 101.3 kN/m² and neglect any resistance to diffusion of benzene beyond the air film. %3Darrow_forwardExplain the cooling effect of evaporation in terms of latent heat of evaporation.arrow_forwardWater is to be boiled at atmospheric pressure in a polished copper pan placed on top of a heating unit. The diameter of the bottom of the pan is 00.2 m. If during 30 minutes the water level is dropped by 0.1 m, calculate the inner surface of the bottom of the pan. Assumptions 1 Steady operating conditions exist. 2 Heat losses from the heater and the pan are negligible 3 The boiling regime is nucleate boiling. Note. Write your answer step by step and clearly explain your work. You need to upload a file.arrow_forward
- Analyze the condensation process using both chillers. Provide operating temperatures and pressures entering each component shown in the diagram (at points 1, 2, 3, 4). Indicate which chiller should be chosen based on the economics. See below for details: -Your work is replacing a chiller that is used as part of a distillation process that condenses methanol (boiling point = 65 °C). Your task is to select the most economical type of system. A conventional chiller will have a lower first cost and will have lower maintenance costs than one that involves enhanced heat transfer surfaces, but the chiller with enhanced surfaces will condense the same amount of alcohol with a lower energy consumption. Select the appropriate chiller by considering the net present value of both systems. That value will involve the first cost of the chiller, and the present value of the maintenance and energy costs. The chiller uses a standard vapor-compression refrigeration cycle with R-22 (see Figure 1). For…arrow_forwardThe wear resistance of a steel gear is to be improved by hardening its surface. This is to be accomplished by increasing the carbon content within an outer surface layer as a result of case-hardening. The carbon is to be supplied from an external carbon-rich gaseous atmosphere at an elevated and constant temperature. The initial carbon content of the steel is kept as a constant and is 0.20 wt%. The surface concentration is to be maintained at 1.00 wt%. For this treatment to be effective, (a) What diffusion process can be assumed in this situation? (b) What type of solid solution is it for the steel after diffusion? (c) What is the diffusion coefficient of carbon in steel if the heat treatment is conducted at 800 ℃? (d) How long will it take to achieve a carbon content of 0.60wt% at a position 0.75 mm below the surface at 1050 ℃?arrow_forwardDetermine the evaporation rate when a container contains hot water and the surface temperature of the container is 75◦C is placed in an air stream that has a mass fraction of water equal to 0.25. For the water over pan If the average mass transfer coefficient is gm,H2O = 0.370 kg/m2·s and the container has a surface area of 0.16 m2 Please make it fast , if not sure skip ,don't give wrong , may downvotearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license