Bending Beams
If you bend a rod down, it compresses the lower side of the rod and stretches the top, resulting in a restoring force. Figure I.4 shows a
FIGURE 1.4
beam of length L, width w, and thickness t fixed at one end and free to move at the other. Deflecting the end of the beam causes a restoring force F at the end of the beam. The magnitude of the restoring force F depends on the dimensions of the beam, the Young’s modulus Y for the material, and the deflection d. For small values of the deflection, the restoring force is
This is similar to the formula for the restoring force of a spring, with the quantity in brackets playing the role of the spring constant k.
When a 70 kg man stands on the end of a springboard (a type of diving board), the board deflects by 4.0 cm.
If the board is replaced by one that is half the length but otherwise identical, how much will it deflect when a 70 kg man stands on the end?
A. 0.50 cm
B. 1.0 cm
C. 2.0 cm
D. 4.0 cm
Want to see the full answer?
Check out a sample textbook solutionChapter P Solutions
College Physics: A Strategic Approach (3rd Edition)
Additional Science Textbook Solutions
Life in the Universe (4th Edition)
Essential University Physics: Volume 1 (3rd Edition)
University Physics Volume 1
An Introduction to Thermal Physics
The Cosmic Perspective
College Physics: A Strategic Approach (4th Edition)
- A uniform rod of mass M and length L is attached to a pivot with negligible friction as shown. The pivot is attached to a wall and the bar starts oriented Pivot horizontally. Use the given variables and the acceleration of gravity, g, to.answer the questions symbolically. L.arrow_forwardA board of mass mand length l is attached to a wall and a rope that makes an angle of theta, as shown. A block of mass M hangs from the right end of the board. 1. Using variables, write Newton’s 2nd law in the x-direction.Hint: You can leave the hinge force as Fhinge x. 2. Using variables, write Newton’s 2nd law in the x-direction.Hint: You can leave the hinge force as Fhinge y.arrow_forwardA heavy crate needs to be moved. A crane can provide the force F at the mounting point shown. a.) Determine the moment about point A due to the force F. Enter your answer in Cartesian components with units of ft-lbs. Round to 3 significant digits. F = (100 i + 2453) lb A x α α Values for dimensions on the figure are given in the table below. R. Variable Value 39 in 35° a. MA = X F î+ k) ft-lbarrow_forward
- A force of 80 N acts on the handle of the paper cutter at A as shown in the figure below. What is the moment created by this force about the hinged at O if 0 = 60°. a) b) At what angle 0 should the force be applied so that the moment it creates about point O is a maximum? c) What is the maximum moment of force at point A? F = 80 N. 10 mm 400 mm 30°arrow_forwardA force of 50 N is applied at the end of a wrench handle that is 24 cm long. The force is applied in a direction perpendicular to the handle.a. What is the torque applied to the nut by the wrench?b. What would the torque be if the force were applied half way up the handle instead of at the end? Use the correct formula to get the correct answer.arrow_forwardDetermine the second moment of area (Ixx) about the centroidal x-axis for the solid homogeneous beam section shown below, where the dimensions are b = 5.25 mm and d= 12.75 mm. Give your answer in mm4 to two decimal places. %3Darrow_forward
- A uniform disk of mass 500 kg and radius 0.25 m is mounted on frictionless bearings so it can rotate freely around a vertical axis through its center (see the following figure). A cord is wrapped around the rim fo the disk and pulled with a force of 10 N. (a) How much work has the force done at the instant the disk has completed three revolutions, starting from rest? (b) Determine the torque due to the force, then calculate the work done by this torque at the instant the disk has completed three revolutions? (c) What is the angular velocity at the instant? (d) What is the power output of the force at that instant?arrow_forwardPlease write the unitsarrow_forwardForces are applied on the beam as shown on the figure at right: a. Find the torque about point P produced by each of the three forces. b. Find the net torque about point P. c. A fourth force is applied to the beam at a distance of 0.30 m to the right of point P. What must the magnitude 15 N 0.25m P 0.15m 0.2m and direction of this force be to make 20 N 5 N the beam in rotational equilibrium?arrow_forward
- 1. Do you think the radius and length of the wire would change the rigidity modulus? Explain your answer. Rectangular Snip 2. How the moment of inertia of the cylindrical mass would change? 3. Do you think we would the similar results if we use a circular disc instead of cylindrical mass? Explain your answer.arrow_forwardEll. Two forces are applied to a merry-go-round with a radius of 1.2 m as shown in the diagram below. One force has a magnitude of 80 N and the other a magnitude of 50 N. a. What is the torque about the axle of the merry-go-round due to the 80-N force? b. What is the torque about the axle due to the 50-N force? c. What is the net torque acting on the merry-go-round?arrow_forwardTwo boys with masses of 40 kg and 60 kg stand on a horizontal frictionless surface holding the ends of a light 10-m long rod. The boys pull themselves together along the rod. When they meet the 40-kg boy will have moved what distance? O a. 5 m O b. need to know the forces they exert O d. 10 m O e. 6 marrow_forward
- University Physics Volume 1PhysicsISBN:9781938168277Author:William Moebs, Samuel J. Ling, Jeff SannyPublisher:OpenStax - Rice UniversityGlencoe Physics: Principles and Problems, Student...PhysicsISBN:9780078807213Author:Paul W. ZitzewitzPublisher:Glencoe/McGraw-Hill