A force of 80 N acts on the handle of the paper cutter at A as shown in the figure below. What is the moment created by this force about the hinged at O if 0 = 60°. a) b) At what angle 0 should the force be applied so that the moment it creates about point O is a maximum? c) What is the maximum moment of force at point A? F = 80 N, 10 mm 400 mm 30°

A force of 80 N acts on the handle of the paper cutter at A as shown in the figure below. What is the moment created by this force about the hinged at O if 0 = 60°. a) b) At what angle 0 should the force be applied so that the moment it creates about point O is a maximum? c) What is the maximum moment of force at point A? F = 80 N, 10 mm 400 mm 30°

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Sl units of bending moment is kN^2 O kN.m km O kN
Problem#4: А thin and light rod with 7-ft length is resting horizontally on a pivot through a point 2.5 ft from the left end. To maintain the balance and avoid a rotational motion of the rod, a 23 is hung is applied the right end downwards at the left end. Calculate the force applied at the left end lbs block at and another force and the normal force exerted by the pivot on the rod.
4.0 m A 7.0 m 3.0 m B+ C Two forces can be replaced by an equivalent force R acting at point B on the beam. Determine the moment of the force R at point A.(Hint: The combined moment of the two forces about any point is equal to the moment of R about the same point.) * O E MA = P (15 m) O E MA = -P (15 m) Ο ΣΜΑ=P(12 m) Ο ΣΜΑ=-P (12 m)
0.20 L 0.40 L 3. The foot of a ladder rests against a wall and its top is held by a tie rope, as shown in the figure. The ladder weighs 100 N, & its center of gravity is 0.40 of its length from the foot. A 150 N child hangs from the rung that is 0.20 of the length from the top. Determine the tension in the tie rope and the components of the force on the foot of the ladder. Tie rope IS0 N 37 100 N
A uniform solid plastic sphere and a hollow metal ball having equal external radius R are released from rest in a vacuum chamber at the same time and height. When each has fallen 1m from their initial position, they both have the same: A. speed (v) B. moment of inertia (1) C. momentum (p) D. change in potential energy (AU)
Suppose you start an antique car by exerting a force of 350 N on its crank for 0.16 s.Randomized Variablesf = 350 Nt = 0.16 sd = 0.22 m What angular momentum is given to the engine if the handle of the crank is 0.22 m from the pivot and the force is exerted to create maximum torque the entire time?
40 m 120 mm 40 mm 40 min 40 mm 40 mm Determine the distance x to the centroid of the beam's cross-sectional area, then find the moment of inertia about y' axis.
Problem 10: A long uniform-density beam has a mass M and a length L. It is hinged to a wall at its left end. A cable is attached to the middle of the rod as shown. A point mass m is attached to the far end. m. What is the correct N2L torque equation for this configuration? MultipleChoice : 1) T sin 0 – migL – M85 = 0 2) T sin 0 – m1gL – Mg = 0 L 3) T cos 0 - mīgL – Mg = 0 4) T cos 0 + m¡gL+ Mg¬ = 0 5) T sin 0 + mgL+ MgL = 0
Calculate the moment of inertia (mm) of the composite area about the yo axis Take t=36 mm. 100 mm t mm t/2 mm 140 mm t mm t mm 100 mm
The crew on peg leg Petes' ship have mutinied. Now Pete finds himself walking the plank. The plank is 4.5m long and has a mass of 13kg. 3.6 meters of the plank extend out over the waters. The plank pivots on a small rail at the edge of the ship, this is the only point of the plank in direct contact with the ship. The remaining meter of the plank is held in place over the deck by the metal bar. The bar is .6m from the pivot. If Pete has a mass of 111kg, what is the torque provided by the bar when Pete is at the end of the plank?
A metal plate is fixed at point B. Several forces are loaded onto the plate Question 5 as shown. Calculate the total moment about point B due to these loads. FA = 20 N FB = 30 N Fc = 20 N FD = 30 N 0 = 30°
Q) A simplified model as shown in figure below of a planar robotic am. You may assume that each segment has length 1.5 m, and the applied force is 250 N. 0, = 35" and 02 = 0; = 20°. Calculate the moment that the force, F, exerts about the point A. F 0: A