Materials for Civil and Construction Engineers (4th Edition)
4th Edition
ISBN: 9780134320533
Author: Michael S. Mamlouk, John P. Zaniewski
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 4, Problem 4.11QP
A 3003-H14 aluminum alloy rod with 0.5 in. diameter is subjected to a 2000- lb tensile load. Calculate the resulting diameter of the rod. If the rod is subjected to a compressive load of 2000 lb, what will be the diameter of the rod? Assume that the modulus of elasticity is 10,000 ksi, Poisson’s ratio is 0.33, and the yield strength is 21 ksi.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A 3003-H14 aluminum alloy rod with 0.5 in. diameter is subjected to a 2000- lb tensile load. Calculate the resulting diameter of the rod. If the rod is sub- jected to a compressive load of 2000 lb, what will be the diameter of the rod? Assume that the modulus of elasticity is 10,000 ksi, Poisson’s ratio is 0.33, and the yield strength is 21 ksi.
An aluminum alloy cylinder with a diameter of 76 mm and a height of
150 mm. is subjected to a compressive load of 220 kN. Assume that the mate-rial is within the elastic region and a modulus of elasticity of 75 GPa.
a. What will be the lateral strain if Poisson’s ratio is 0.33?b. What will be the diameter after load application?c. What will be the height after load application?
Pls answer thanks
Chapter 4 Solutions
Materials for Civil and Construction Engineers (4th Edition)
Ch. 4 - Name the two primary factors that make aluminum an...Ch. 4 - Prob. 4.2QPCh. 4 - An aluminum alloy specimen with a radius of 0.28...Ch. 4 - An aluminum alloy bar with a radius of 7 mm was...Ch. 4 - Decode the characteristics of a 6063 T831...Ch. 4 - A round aluminum alloy bar with a 0.6 in. diameter...Ch. 4 - An aluminum alloy bar with a rectangular cross...Ch. 4 - A round aluminum alloy bar with a 0.25-in....Ch. 4 - An aluminum alloy rod has a circular cross section...Ch. 4 - An aluminum alloy cylinder with a diameter of 3...
Ch. 4 - A 3003-H14 aluminum alloy rod with 0.5 in....Ch. 4 - The stressstrain relation of an aluminum alloy bar...Ch. 4 - An aluminum specimen originally 300 mm long is...Ch. 4 - A tension stress of 40 ksi was applied on a 12-in....Ch. 4 - A tension test was performed on an aluminum alloy...Ch. 4 - In Problem 4.15, plot the stressstrain...Ch. 4 - Referring to Figure 4.5, determine approximate...Ch. 4 - Prob. 4.18QPCh. 4 - A tensile stress is applied along the long axis of...Ch. 4 - A cylindrical aluminum alloy rod with a 0.5 in....Ch. 4 - Prob. 4.21QPCh. 4 - Discuss galvanic corrosion of aluminum. How can...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.arrow_forwardThe results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.arrow_forwardA metal rod with 10mm diameter is subjected to 9kN tensile load. Calculate the resulting diameter of the rod after loading. Assume that the modulus of elasticity is70 GPa, Poisson’s ratio is 0.33, and the yield strength is145MPa.arrow_forward
- Part A An aluminum 2014-T4 alloy bar 2.50 inches wide and 0.750 inches in thickness has a 1/4 inch radius hole centered on its width, as shown in the sketch. With an axial load, P = 8650 lbs applied, the maximum axial stress at the edges of the hole was experimentally determined to be 7670 psi What is the stress concentration factor, K, of the hole? 1.33 0.75 1.66 1.50 P 2.50 in. -Radius 1/4 in. P= 8650 lbsarrow_forwardA torsion test shows that the shear modulus of an aluminum specimen is 27.6 GPa. When the same specimen is used in a tensile test, the modulus of elasticity is found to be 73.2 GPa. Find the Poisson's ratio for the specimen.arrow_forwardA tension stress of 70 ksi was applied on a 12-in. long steel specimen. Determine the resultant elongation assuming that the deformation is entirely elastic. Assume a Young’s modulus of 30 * 106 psi.arrow_forward
- A tensile test is performed on a brass specimen 10mm in diameter using a gage lenght of 50mm. When the tensile load P reachers a value of 20kN, the distance between the gage marks has increased by 0.122 mm. What is the modulus of elasticity of the brass.arrow_forwardAn aluminum alloy cylinder with a diameter of 76 mm and a height of150 mm. is subjected to a compressive load of 220 kN. Assume that the material is within the elastic region and a modulus of elasticity of 75 GPa.a. What will be the lateral strain if Poisson’s ratio is 0.33?b. What will be the diameter after load application?c. What will be the height after load application?arrow_forwardA 3003-H14 aluminum alloy rod with 15 mm diameter is subjected to a 9-kNtensile load. Calculate the resulting diameter of the rod. If the rod is subjectedto a compressive load of 9 kN, what will be the diameter of the rod? Assumethat the modulus of elasticity is 70 GPa, Poisson’s ratio is 0.33, and the yieldstrength is 145 MPa.arrow_forward
- Testing a round steel alloy bar with a diameter of 15 mm and a gauge length of 250 mm produced the stress-strain relationship shown in Figure P3.28. Determine a. the elastic modulus b. the proportional limit c. the yield strength at a strain offset of 0.002 d. the tensile strength e. the magnitude of the load required to produce an increase in length of 0.38 mm f. the final deformation, if the specimen is unloaded after being strained by the amount specified in (e) g. In designing a typical structure made of this material, would you expect the stress applied in (e) reasonable? Why? 750 500 250 0.01 0.02 0.03 0.04 Strain, m/m FIGURE P3.28 Stress, MPaarrow_forward7. A solid aluminum cylinder is placed within an ASTM A501 steel tube as shown. Compute the stresses in the two materials with an applied load of 45,000 lbs. 45,000 lbs 3.5"Ø 3.0"Ø Steel Aluminumarrow_forwardA cylindrical specimen of stainless steel having an initial diameter of 12.8?? and initial length of 50.8?? is pulled in tension. Use the data provided below to a) Plot the data as engineering stress versus engineering strain using excel or similar software. b) Compute the modulus of elasticity. c) Determine the yield strength at a strain offset of 0.002. d) Determine the tensile strength of this alloy. e) What is the approximate ductility, in percent elongation? f) Compute the modulus of resilience. Load (?) Length (??) 0 50.800 12,700 50.825 25,400 50.851 38,100 50.876 50,800 50.902 76,200 50.952 89,100 51.003 92,700 51.054 102,500 51.181 107,800 51.308 119,400 51.562 128,300 51.816 149,700 52.832 159,000 53.848 160,400 54.356 159,500 54.864 151,500 55.880 124,700 56.642 Fracturearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Steel Design (Activate Learning with these NEW ti...Civil EngineeringISBN:9781337094740Author:Segui, William T.Publisher:Cengage Learning
Materials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage Learning
Steel Design (Activate Learning with these NEW ti...
Civil Engineering
ISBN:9781337094740
Author:Segui, William T.
Publisher:Cengage Learning
Materials Science And Engineering Properties
Civil Engineering
ISBN:9781111988609
Author:Charles Gilmore
Publisher:Cengage Learning
Material Properties 101; Author: Real Engineering;https://www.youtube.com/watch?v=BHZALtqAjeM;License: Standard YouTube License, CC-BY