DeGarmo's Materials and Processes in Manufacturing
12th Edition
ISBN: 9781118987674
Author: J. T. Black, Ronald A. Kohser
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 29, Problem 87RQ
What is important about a dual�beam focused ion beam and scanning electron microscope (dual�beam FIB/SEM)?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Suppose NASA sent a robotic craft to explore the deep oceans of Jupiter’s moon, Europa (assume the ocean water has an index of refraction 1.34) . In an attempt to be discrete, NASA applies a coating to the submarine-like craft, to make it indetectable to any creatures in the ocean who can see light with a wavelength of 1200nm. The coating material has anindex of refraction of 1.25.a) Draw a clear physics diagram of the problem.b) Technology only allows for coatings to be 1 micrometer or thicker. What is the thinnest coating that can be applied to the craft to make it invisible at 1200nm.
2. In lithography process, you are asked to deposit nanoparticle in holes. Select the process steps in order.
Resist
A metal
elching
Substrate
After development
SHiping
Nanomaterial
of resist
deposited in holes
wetChem cal)
(a) Striping resist Deposition of nanomaterial -Etching
(b) Etching - Deposition of nanomaterial Striping resist
(c) Deposition of nanomaterial- Striping resist Etching
Cmone
d)Please explain how to distinguish the types of defects that can be detected using X-Rays and AMI.
Chapter 29 Solutions
DeGarmo's Materials and Processes in Manufacturing
Ch. 29 - Over the latter half of the 20th century, what...Ch. 29 - What was the major motivation for developing...Ch. 29 - Prob. 3RQCh. 29 - What is an example of a device feature that is...Ch. 29 - What type of manufacturing technology dominates...Ch. 29 - Name the four categories of miniature systems...Ch. 29 - Give two differences between lab-on-a-chip and...Ch. 29 - What is a scaling law?Ch. 29 - As the primary dimensions of an object decrease,...Ch. 29 - In the design of a water heater, the mean time...
Ch. 29 - Prob. 11RQCh. 29 - Name two conventional manufacturing processes that...Ch. 29 - Prob. 13RQCh. 29 - Why does breadth of scale of a product have an...Ch. 29 - What is the most complicated, expensive, and...Ch. 29 - Name three purposes that a resist mask can play.Ch. 29 - Name four key lithography methods.Ch. 29 - Name two through-mask lithography techniques.Ch. 29 - Name two direct-write lithography techniques.Ch. 29 - List the sequence of steps involved in...Ch. 29 - Of the two major classifications of photoresists,...Ch. 29 - List four requirements of a photoresist.Ch. 29 - What limits the resolution of a photoresist?Ch. 29 - What is meant by resist sensitivity?Ch. 29 - What is one requirement that contributes to the...Ch. 29 - List the three types of exposure methods used in...Ch. 29 - Why is projection printing equipment called a...Ch. 29 - What are typical materials etched during...Ch. 29 - What is etch bias?Ch. 29 - Prob. 30RQCh. 29 - What are some possible defects that can result...Ch. 29 - What are some possible defects that can result...Ch. 29 - List and describe two properties of etchants.Ch. 29 - What is etch anisotropy dependent upon?Ch. 29 - What is the difference between wet and dry?...Ch. 29 - What is dry etching?Ch. 29 - What are the three main categories of dry etching...Ch. 29 - What is the difference between plasma etching and...Ch. 29 - What is deep reactive ion etching?Ch. 29 - What is a benefit of using UV lasers to machine...Ch. 29 - Which type of non-lithographic micromachining...Ch. 29 - What are thin films?Ch. 29 - A) What is the difference between solution...Ch. 29 - What are the two broad categories of vapor...Ch. 29 - List two different types of physical vapor...Ch. 29 - List two advantages of sputtering over...Ch. 29 - What is meant by step coverage with regards to...Ch. 29 - Why is step coverage important?Ch. 29 - Prob. 49RQCh. 29 - What does gettering mean in relation to wafer...Ch. 29 - How are undesirable gas-phase reactions controlled...Ch. 29 - What is the key difference in the reactor designs...Ch. 29 - What are the two types of LPCVD reactor designs?...Ch. 29 - In metallization, what is the difference between a...Ch. 29 - What is the advantage of using plasma-enhanced on...Ch. 29 - A) What is epitaxy? B) is it important for...Ch. 29 - Name four techniques for solution deposition onto...Ch. 29 - Name four roll-to-roll processing techniques for...Ch. 29 - What is a semiconductor?Ch. 29 - Name three common semiconductor materials.Ch. 29 - Give three reasons why silicon is the most popular...Ch. 29 - Prob. 62RQCh. 29 - What is a silicon boule?Ch. 29 - Prob. 64RQCh. 29 - What are some geometric concerns involved with...Ch. 29 - What is meant by the term doping?Ch. 29 - What is the difference between n�type and...Ch. 29 - Name three methods for doping a silicon wafer.Ch. 29 - Prob. 69RQCh. 29 - Prob. 70RQCh. 29 - Prob. 71RQCh. 29 - Why are rapid thermal processing technologies...Ch. 29 - What are two ways in which silicon dioxide is...Ch. 29 - Give two reasons why wet oxidation is better...Ch. 29 - What is a p�n junction? \What can it be used...Ch. 29 - Prob. 76RQCh. 29 - Assuming an n�doped substrate is clean, list the...Ch. 29 - What is planarization and why is it needed?Ch. 29 - What is meant by the term ULSI?Ch. 29 - In general, what technological breakthroughs were...Ch. 29 - What drives the increase in component density and...Ch. 29 - Why are clean rooms so important to...Ch. 29 - What is the advantage of electron microscopy over...Ch. 29 - What is the collective advantage of...Ch. 29 - Why do samples analyzed in an electron microscopes...Ch. 29 - What are two differences between a scanning...Ch. 29 - What is important about a dual�beam focused ion...Ch. 29 - Why is white light normally preferred for...Ch. 29 - What is one advantage of an atomic force...Ch. 29 - What is the breadth of scale of an automotive...Ch. 29 - What is the breadth of scale of a computer...Ch. 29 - Which has a larger breadth of scale, the...Ch. 29 - Prob. 4PCh. 29 - A piece of silicon has an integrated resistor...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Write down the correct miller index notation for any direction that is perpendicular to the direction [110]arrow_forwardMagnetic resonance imaging (MRI) is a medical imaging technique that located in hospitals and radiology centers. MRI uses a strong magnetic field and radio waves to create detailed images of the organs and tissues within the body. (i) MRI system operators must make sure not to carry any metallic objects when they enter the room that house the MRI, even when the machine is not operating. Give the reason. (ii) What happens if a magnet was hitted with a hammer repeatedly? Explain your answer. Robots are used in automobile industries to weld two components at specific locations. Thus, the end position of the robot arms must be determined accurately in order to weld the components at the precise position. In selecting a proper material for the robot arms design, identify the factors must be considered for this application.arrow_forwardAnswer each of the following questions in one to three sentences. (a) What is lithography field? (b) What is misalignment in lithography? (e) What is selectivity in an etching process? (d) What is end-point detection in an etching process?arrow_forward
- 4. Poly-Si of the following structure is to be etched using a completely anisotropic dry-etch process, to remove poly-Si at a rate of 0.1 mm /min. However, this etching process has poor selectivities: selectivity to SiO₂ is 5; selectivity to photoresist is 2. (a) Sketch the cross-section after 5 minutes of etching. (b) Calculate the angle of the SiO₂ sidewalls after 5 minutes of etching. 0.lum oxide 1 um 0.7um Poly-Si I photoresist 0.5 umarrow_forwardIs this true or false pleasearrow_forwardi need the answer quicklyarrow_forward
- Don't Use Chat GPT Will Upvote And Give Handwritten Solution Pleasearrow_forwardMultiple choice questions, please help thank you!! 1. The chemical potential (μ) of smaller size clusters is bigger than that of bigger size clusters because of (a) their small size (b) the fewer number of atoms in them (c) surface area is smaller (d) their surface is more curved 2. Which of these characteristics would you associate with SEM: A surface imaging tool Maintained under vacuum Provides imaging and compositional data Uses a scanned electron beam All of the above 3. Secondary electrons (SE) are best described as Low energy electrons from the sample surface High energy electrons from the sample surface Low energy primary beam electrons High energy primary beam electrons 4. Atomic force microscopy (AFM) is the most widely used form of scanning probe microscopes for the characterization of nanomaterials since it require: (a) electrically conductive and optically transparent samples (b) neither electrically conductive nor optically transparent samples (c) electrically…arrow_forwardSolve it correctly please. Iarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Material Properties 101; Author: Real Engineering;https://www.youtube.com/watch?v=BHZALtqAjeM;License: Standard YouTube License, CC-BY