DeGarmo's Materials and Processes in Manufacturing

12th Edition

ISBN: 9781118987674

Author: J. T. Black, Ronald A. Kohser

Publisher: WILEY

See similar textbooks

Videos

Textbook Question

Chapter 29, Problem 50RQ

What does gettering mean in relation to wafer production?

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 29, Problem 49RQ

Chapter 29, Problem 51RQ

Students have asked these similar questions

Does Czochralski crystal growth the only method for Si wafer production? What is the max. pull rate to obtain a 12-inch diameter Ge wafer

Write in detail following terminologies according to wafer fabrication processes: a. Diffusion and Ion Implantation b. Metallization c. Etching

For a given 40 cm diameter wafer, and a die that is 1.5 cm x 2 cm, determine the cost of a die. Wafer cost is $5800, wafer yield is 100%, and defects per unit area is 0.09/sq. cm.

Chapter 29 Solutions

DeGarmo's Materials and Processes in Manufacturing

Ch. 29 - Over the latter half of the 20th century, what...Ch. 29 - What was the major motivation for developing...Ch. 29 - Prob. 3RQ Ch. 29 - What is an example of a device feature that is...Ch. 29 - What type of manufacturing technology dominates...Ch. 29 - Name the four categories of miniature systems...Ch. 29 - Give two differences between lab-on-a-chip and...Ch. 29 - What is a scaling law?Ch. 29 - As the primary dimensions of an object decrease,...Ch. 29 - In the design of a water heater, the mean time...

Ch. 29 - Prob. 11RQ Ch. 29 - Name two conventional manufacturing processes that...Ch. 29 - Prob. 13RQ Ch. 29 - Why does breadth of scale of a product have an...Ch. 29 - What is the most complicated, expensive, and...Ch. 29 - Name three purposes that a resist mask can play.Ch. 29 - Name four key lithography methods.Ch. 29 - Name two through-mask lithography techniques.Ch. 29 - Name two direct-write lithography techniques.Ch. 29 - List the sequence of steps involved in...Ch. 29 - Of the two major classifications of photoresists,...Ch. 29 - List four requirements of a photoresist.Ch. 29 - What limits the resolution of a photoresist?Ch. 29 - What is meant by resist sensitivity?Ch. 29 - What is one requirement that contributes to the...Ch. 29 - List the three types of exposure methods used in...Ch. 29 - Why is projection printing equipment called a...Ch. 29 - What are typical materials etched during...Ch. 29 - What is etch bias?Ch. 29 - Prob. 30RQ Ch. 29 - What are some possible defects that can result...Ch. 29 - What are some possible defects that can result...Ch. 29 - List and describe two properties of etchants.Ch. 29 - What is etch anisotropy dependent upon?Ch. 29 - What is the difference between wet and dry?...Ch. 29 - What is dry etching?Ch. 29 - What are the three main categories of dry etching...Ch. 29 - What is the difference between plasma etching and...Ch. 29 - What is deep reactive ion etching?Ch. 29 - What is a benefit of using UV lasers to machine...Ch. 29 - Which type of non-lithographic micromachining...Ch. 29 - What are thin films?Ch. 29 - A) What is the difference between solution...Ch. 29 - What are the two broad categories of vapor...Ch. 29 - List two different types of physical vapor...Ch. 29 - List two advantages of sputtering over...Ch. 29 - What is meant by step coverage with regards to...Ch. 29 - Why is step coverage important?Ch. 29 - Prob. 49RQ Ch. 29 - What does gettering mean in relation to wafer...Ch. 29 - How are undesirable gas-phase reactions controlled...Ch. 29 - What is the key difference in the reactor designs...Ch. 29 - What are the two types of LPCVD reactor designs?...Ch. 29 - In metallization, what is the difference between a...Ch. 29 - What is the advantage of using plasma-enhanced on...Ch. 29 - A) What is epitaxy? B) is it important for...Ch. 29 - Name four techniques for solution deposition onto...Ch. 29 - Name four roll-to-roll processing techniques for...Ch. 29 - What is a semiconductor?Ch. 29 - Name three common semiconductor materials.Ch. 29 - Give three reasons why silicon is the most popular...Ch. 29 - Prob. 62RQ Ch. 29 - What is a silicon boule?Ch. 29 - Prob. 64RQ Ch. 29 - What are some geometric concerns involved with...Ch. 29 - What is meant by the term doping?Ch. 29 - What is the difference between nâ€�type and...Ch. 29 - Name three methods for doping a silicon wafer.Ch. 29 - Prob. 69RQ Ch. 29 - Prob. 70RQ Ch. 29 - Prob. 71RQ Ch. 29 - Why are rapid thermal processing technologies...Ch. 29 - What are two ways in which silicon dioxide is...Ch. 29 - Give two reasons why wet oxidation is better...Ch. 29 - What is a pâ€�n junction? \What can it be used...Ch. 29 - Prob. 76RQ Ch. 29 - Assuming an nâ€�doped substrate is clean, list the...Ch. 29 - What isÂ planarizationÂ and why is it needed?Ch. 29 - What is meant by the term ULSI?Ch. 29 - In general, what technological breakthroughs were...Ch. 29 - What drives the increase in component density and...Ch. 29 - Why are clean rooms so important to...Ch. 29 - What is the advantage of electron microscopy over...Ch. 29 - What is the collective advantage of...Ch. 29 - Why do samples analyzed in an electron microscopes...Ch. 29 - What are two differences between a scanning...Ch. 29 - What is important about a dualâ€�beam focused ion...Ch. 29 - Why is white light normally preferred for...Ch. 29 - What is one advantage of an atomic force...Ch. 29 - What is the breadth of scale of an automotive...Ch. 29 - What is the breadth of scale of a computer...Ch. 29 - Which has a larger breadth of scale, the...Ch. 29 - Prob. 4P Ch. 29 - A piece of silicon has an integrated resistor...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.