PEARSON ETEXT ENGINEERING MECH & STATS
15th Edition
ISBN: 9780137514724
Author: HIBBELER
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 17, Problem 72P
To determine
The time required to stop the motion and the horizontal and vertical components of force which the member AB exerts on the pin at A during this time.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The body A with a mass of 50 kg is in equilibrium with the help of the pulling force generated in the AB and AC cables in the middle of the inclined plane and the friction force between the curved surface and the object.
The friction force is on the line of motion of body A and develops in the opposite direction to the movement in the direction of the arrow shown in the drawing.
Since the pulling force in AB and AC cables is 15.1 and 22.1 N, respectively, calculate the balancer friction force acting on the object vectorially? (g = 9.81 m / s'2)
Two bodies A and B, each weighing 96.6 lb, are connected by a rigid bar of negligible weight attached to them at their gravity centers. The coefficient of friction at the wall and floor is 0.268 if the bodies start from rest at the given position, determine the acceleration of B at this instant. Simplify the solution by creating dynamic equilibrium and taking a moment summation about the intersection of the wall and floor reactions. Explain why these reactions pass through the gravity center of B and A respectively.
4. The pipe has a mass of 600 kg and is being towed behind a truck. If the angle 0 = 30°,
determine the acceleration of the truck and the tension in the cable. The coefficient of kinetic
friction between the pipe and the ground is Hk = 0.1.
B
45°
Ge
0.4 m
Chapter 17 Solutions
PEARSON ETEXT ENGINEERING MECH & STATS
Ch. 17 - Determine the moment of inertia Iy for the slender...Ch. 17 - The solid cylinder has an outer radius R1 height...Ch. 17 - Determine the moment of inertia of the thin ring...Ch. 17 - Prob. 9PCh. 17 - The pendulum consists of a 4-kg circular plate and...Ch. 17 - Prob. 12PCh. 17 - The wheel consists of a thin ring having a mass of...Ch. 17 - If the large ring, small ring and each of the...Ch. 17 - Determine the moment of inertia about an axis...Ch. 17 - Prob. 16P
Ch. 17 - Determine the location y of the center of mass G...Ch. 17 - Prob. 18PCh. 17 - Prob. 19PCh. 17 - Determine the moment of inertia of the wheel about...Ch. 17 - The pendulum consists of the 3-kg slender rod and...Ch. 17 - Prob. 22PCh. 17 - Determine the moment of inertia of the overhung...Ch. 17 - Prob. 1FPCh. 17 - Prob. 2FPCh. 17 - Prob. 3FPCh. 17 - Prob. 4FPCh. 17 - At the instant shown both rods of negligible mass...Ch. 17 - Prob. 6FPCh. 17 - The door has a weight of 200 lb and a center of...Ch. 17 - The door has a weight or 200 lb and a center of...Ch. 17 - The jet aircraft has a total mass of 22 Mg and a...Ch. 17 - The sports car has a weight of 4500 lb and center...Ch. 17 - The bar has a weight per length w and is supported...Ch. 17 - The smooth 180-lb pipe has a length of 20 ft and a...Ch. 17 - The smooth 180-lb pipe has a length of 20 ft and a...Ch. 17 - Prob. 44PCh. 17 - If the carts mass is 30 kg and it is subjected to...Ch. 17 - Prob. 50PCh. 17 - Prob. 53PCh. 17 - Prob. 54PCh. 17 - The 100-kg wheel has a radius of gyration about...Ch. 17 - Prob. 8FPCh. 17 - Prob. 9FPCh. 17 - Prob. 10FPCh. 17 - Prob. 11FPCh. 17 - Prob. 12FPCh. 17 - The 10-kg wheel has a radius of gyration kA = 200...Ch. 17 - The uniform 24-kg plate is released from rest at...Ch. 17 - The uniform slender rod has a mass m. If it is...Ch. 17 - The tent rod has a mass of 2 kg/m. If it is...Ch. 17 - Disk A has a weight of 5 lb and disk B has a...Ch. 17 - Prob. 66PCh. 17 - The reel of cable has a mass of 400 kg and a...Ch. 17 - Prob. 72PCh. 17 - Cable is unwound from a spool supported on small...Ch. 17 - The 5-kg cylinder is initially at rest when it is...Ch. 17 - Prob. 76PCh. 17 - Disk D turns with a constant clockwise angular...Ch. 17 - Prob. 78PCh. 17 - Prob. 81PCh. 17 - Prob. 85PCh. 17 - The Catherine wheel is a firework that consists of...Ch. 17 - The uniform 60-kg slender bar is initially at rest...Ch. 17 - Prob. 14FPCh. 17 - Prob. 15FPCh. 17 - The 20- kg sphere rolls down the inclined plane...Ch. 17 - The 200-kg spool has a radius of gyration about...Ch. 17 - The 12-kg slender rod is pinned to a small roller...Ch. 17 - If the disk in Fig. 17-19 rolls without slipping,...Ch. 17 - The uniform 150-lb beam is initially at rest when...Ch. 17 - The spool has a mass of 100 kg and a radius of...Ch. 17 - Solve Prob.17-96 if the cord and force P = 50 N...Ch. 17 - The spool has a mass of 100 kg and a radius of...Ch. 17 - A force of F= 10 N is applied to the 10-kg ring as...Ch. 17 - If the coefficient of static friction at C is s =...Ch. 17 - If P = 30 lb, determine the angular acceleration...Ch. 17 - If the coefficient of static friction between the...Ch. 17 - The semicircular disk having a mass of 10 leg is...Ch. 17 - The circular concrete culvert rols with an angular...Ch. 17 - The uniform disk of mass m is rotating with an...Ch. 17 - The uniform disk of mass m is rotating with an...Ch. 17 - The uniform beam has a weight W. If it is...Ch. 17 - The 500-lb beam is supported at A and B when it is...Ch. 17 - Prob. 1RPCh. 17 - Prob. 2RPCh. 17 - Prob. 3RPCh. 17 - Prob. 4RPCh. 17 - Prob. 5RPCh. 17 - Prob. 6RPCh. 17 - Prob. 7RPCh. 17 - Prob. 8RP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Determine the steady-state angle a if the constant force P = 195 N is applied to the cart of mass M = 16 kg. The cart travels on the slope of angle 0 = 25° The pendulum bob has mass m = 4 kg and the rigid bar of length L = 1.1 m has negligible mass. Ignore all friction. P M L marrow_forwardPlease solve this question in dynamicsarrow_forwardDetermine the steady-state angle α if the constant force P = 180 N is applied to the cart of mass M = 9 kg. The cart travels on the slope of angle θ = 16°. The pendulum bob has mass m = 3 kg and the rigid bar of length L = 1.2 m has negligible mass. Ignore all friction.arrow_forward
- The position of the small 0.68-kg blocks in the smooth radial slots in the disk which rotates about a vertical axis at O is used to activate a speed-control mechanism. If each block moves from r = 162 mm to r = 200 mm while the speed of the disk changes slowly from 272 rev/min to 382 rev/min, design the spring by calculating the spring constant k of each spring. The springs are attached to the inner ends of the slots and to the blocks.arrow_forwardThe 15-kg bar is released from rest while in the position shown and its end rollers travel in the vertical-plane slot shown. If the speed of roller A is 3.23 m/s as it passes point C, determine the work done by friction on the system over this portion of the motion. The bar has a length /= 775 mm. Assume 8 = 34° 0 Barrow_forwardThe flat circular disk rotates about a vertical axis through O with a slowly increasing angular velocity w. Prior to rotation, each of the 0.52-kg sliding blocks has the position x = 28 mm with no force in its attached spring. Each spring has a stiffness of 430 N/m. Determine the value of x for each spring for a steady speed of 279 rev/min. Also calculate the normal force N exerted by the side of the slot on the block. The force N is positive if it pushes from the side labeled A. Neglect any friction between the blocks and the slots, and neglect the mass of the springs. (Hint: Sum forces along and normal to the slot.) Answers: X = wwwwwwww N = i i -74-74- mm mm mm Narrow_forward
- A package of mass m is placed inside a drum that rotates in the verticalplane at the constant angular speed ˙ θ = 1.36 rad/s. If the package reaches the position θ = 45◦ before slipping, determine the static coefficient of friction between the package and the drum.arrow_forwardQ5: The 15 kg cylinder rotates with an angular velocity of 40 rad/s. If a force F = 6 N is applied to the AB bar, as indicated, determine the time required to stop rotation. The coefficient of kinetic friction between the bar and the cylinder is 0.4. Disregard the thickness of the bar. F = 6N 400 mm- 500 mm B 150 mm-arrow_forwardThe 40-kg disk is rotating at e = 100 rad/s. When the force Pis applied to the brake as indicated by the graph. If the cocfficient of kinetic friction at B is pe= 0.3, determine the time t needed to stay the disk from rotating. Neglect the thickness of the brake.arrow_forward
- The spring-mounted 0.62-kg collar A oscillates along the horizontal rod, which is rotating at the constant angular rate ở = 6.3 rad/s. At a certain instant, ris increasing at the rate of 630 mm/s. If the coefficient of kinetic friction between the collar and the rod is 0.46, calculate the friction force F exerted by the rod on the collar at this instant. Vertical Answer: F = i Narrow_forwardQ1: The 2-Mg truck achieves a speed of 15 m/s with a constant acceleration after it has traveled a distance of 100 m, starting from rest. Determine the normal force exerted on each pair of front wheels B and rear driving wheels A. Also, find the traction force on the pair of wheels at A. The front wheels are free to roll. Neglect the mass of the wheels Ans.: NB = 10729.3 N, NA = 8890.71 N traction force FA = 2250 N 0.75 m 2 m 1.5 m- $3 Barrow_forwardThe homogeneous, solid cylinder with mass m = 4.8 kg and radius r = 0.24 m rolls along the inclined surface without slipping. If the initial angular velocity is w, = 2 rad/s (counterclockwise), and after a certain time lapse the angular velocity is w2 = 2.2 rad/s (clockwise), determine the magnitude of the linear impulse due to the frictional force during this time period. Let 0 = 46°.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Dynamics - Lesson 1: Introduction and Constant Acceleration Equations; Author: Jeff Hanson;https://www.youtube.com/watch?v=7aMiZ3b0Ieg;License: Standard YouTube License, CC-BY